NSF 336-2018 Sustainability Assessment for Commercial Furnishings Fabric.pdf

1、NSF International Standard / American National StandardNSF/ANSI 336 - 2018Sustainability Assessment for Commercial Furnishings FabricNSF International, an independent, not-for-profit, non-governmental organization, is dedicated to being the leading global provider of public health and safety-based r

2、isk management solutions while serving the interests of all stakeholders. This Standard is subject to revision. Contact NSF to confirm this revision is current. Users of this Standard may request clarifications and interpretations, or propose revisions by contacting: Chair, Joint Committee on Sustai

3、nable Textiles c/o NSF International 789 North Dixboro Road, P. O. Box 130140 Ann Arbor, Michigan 48113-0140 USA Phone: (734) 769-8010 Telex: 753215 NSF INTL FAX: (734) 769-0109 E-mail: infonsf.org Web: http:/www.nsf.orgi NSF/ANSI 3362018 NSF International Standard/ American National Standard for Su

4、stainability Sustainability assessment for commercial furnishings fabric Standard Developer NSF International Designated as an ANSI Standard February 7, 2018 American National Standards Institute ii Prepared by The NSF Joint Committee on Sustainable Textiles Recommended for Adoption by The NSF Counc

5、il of Public Health Consultants Adopted March 2011 Revised February 2018 Published by NSF International P.O. Box 130140, Ann Arbor, Michigan 48113-0140, USA For ordering copies or for making inquiries with regard to this Standard, please reference the designation “NSF/ANSI 336 - 2018.” Copyright 201

6、8 NSF International Previous editions 2011 Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from NSF International. Printed in the United St

7、ates of America. iii Disclaimers1NSF, in performing its functions in accordance with its objectives, does not assume or undertake to discharge any responsibility of the manufacturer or any other party. The opinions and findings of NSF represent its professional judgment. NSF shall not be responsible

8、 to anyone for the use of or reliance upon this Standard by anyone. NSF shall not incur any obligation or liability for damages, including consequential damages, arising out of or in connection with the use, interpretation of, or reliance upon this Standard. NSF Standards provide basic criteria to p

9、romote sanitation and protection of the public health. Provisions for mechanical and electrical safety have not been included in this Standard because governmental agencies or other national standards-setting organizations provide safety requirements. Participation in NSF Standards development activ

10、ities by regulatory agency representatives (federal, local, state) shall not constitute their agencys endorsement of NSF or any of its Standards. Preference is given to the use of performance criteria measurable by examination or testing in NSF Standards development when such performance criteria ma

11、y reasonably be used in lieu of design, materials, or construction criteria. The illustrations, if provided, are intended to assist in understanding their adjacent standard requirements. However, the illustrations may not include all requirements for a specific product or unit, nor do they show the

12、only method of fabricating such arrangements. Such partial drawings shall not be used to justify improper or incomplete design and construction. Unless otherwise referenced, the annexes are not considered an integral part of NSF Standards. The annexes are provided as general guidelines to the manufa

13、cturer, regulatory agency, user, or certifying organization. 1The information contained in this Disclaimer is not part of this American National Standard (ANS) and has not been processed in accordance with ANSIs requirements for an ANS. Therefore, this Disclaimer may contain material that has not be

14、en subjected to public review or a consensus process. In addition, it does not contain requirements necessary for conformance to the Standard. This page is intentionally left blank.v Contents 1 General 1 1.1 Purpose 1 1.2 Scope 1 1.3 Alternate products or materials 2 1.4 Sustainability measurement .

15、 2 1.5 Conformance 3 1.6 Frequency of evaluation . 3 2 Normative references and tools 4 2.1 Normative references . 4 2.2 Informational references 5 3 Definitions 6 4 Defining product process boundaries . 10 5 Fiber sourcing . 11 5.1 Purpose 11 5.2 Scope 11 5.3 Prerequisite credits 11 5.4 Optional cr

16、edits 11 6 Safety of materials 17 6.1 Purpose 17 6.2 Scope 17 6.3 Inventory 17 6.4 Prerequisite credits 17 7 Water conservation . 22 7.1 Purpose 22 7.2 Scope 22 7.3 Water balance 22 7.4 Prerequisite credits 22 7.5 Optional credits 23 8 Water quality . 25 8.1 Purpose 25 8.2 Scope 25 8.3 Prerequisite

17、credits (all facilities) . 25 8.4 Optional credits 26 9 Energy 27 9.1 Purpose 27 9.2 Scope 27 9.3 Prerequisite credits 27 9.4 Optional credits 27 10 Air quality 28 10.1 Purpose . 28 10.2 Scope . 28 10.3 Prerequisite credits 28 10.4 Optional credits 29 11 Recycling practices in manufacturing and end

18、of use 29 11.1 Purpose . 29 11.2 Scope . 29 11.3 Prerequisite credits 29 11.4 Optional credits 30 12 Social accountability . 33 12.1 Purpose . 33 12.2 Scope . 33 12.3 Prerequisite credits 33 12.4 Optional credits 34 Annex A Guidance document 37 Annex B Point structure 57 Annex C Processing subcatego

19、ries in table 7.1 . 63 Annex D Example boundary map . 65 vii Foreword2 This American National Standard, NSF/ANSI 336 Sustainability Assessment for Commercial Furnishings Fabric, has been developed as part of the ongoing efforts of a number of interested parties to document and improve the sustainabi

20、lity profile of commercial fabric products using established and/or advanced scientific principles, practices, materials, and standards. Stakeholders involved in developing the Stand-ard included textile mills, suppliers, end users such as interior design professionals, state agencies re-sponsible f

21、or environmentally preferable product procurement practices, academics, and non-governmental organizations. The purpose of the Sustainability Assessment for Commercial Furnishings Fabric Standard is to establish consistent requirements for sustainable commercial fabric products. These requirements a

22、re intended to form the basis of conformity assessment programs, such as third-party certification or registration. The Sustainability Assessment for Commercial Furnishings Fabric Standard has been designed, in part, to satisfy the following criteria: increase the economic value of sustainable texti

23、les throughout the supply chain by enhancing market demand for sustainable textile products provide information that enables specifiers to sort out the complex information on sustainable at-tributes identify other consensus based standards and sustainable textiles educate and instruct all stakeholde

24、rs in the textiles supply chain encourage competition between the various aspects of the supply chain to seek out or develop environmentally preferable processes, practices, power sources, and materials. engender confidence in the various stakeholders (manufacturers, suppliers, regulators, and consu

25、mers) that products labeled with a third party certification mark consistently meet the requirements of this program. encourage participation by all manufacturers of commercial furnishings fabric to maximize impact reductions and enhance environmental accomplishments. This edition of the Standard co

26、ntains the following revisions: Issue 2 Normative references were updated. This Standard was developed by the NSF Joint Committee on Sustainable Textiles using the consensus process described by the American National Standards Institute. Suggestions for improvement of this Standard are welcome. This

27、 Standard is maintained on a Continuous Maintenance schedule and can be opened for comment at any time. Comments should be sent to Chair, Joint Committee on Sustainable Textiles, NSF International, National Center for Sustainability Standards at ncssnsf.org, or P.O. Box 130140, Ann Arbor, Michigan 4

28、8113-0140, USA. 2The information contained in this Foreword is not part of this American National Standard (ANS) and has not been processed in accordance with ANSIs requirements for an ANS. Therefore, this Foreword may contain material that has not been subjected to public review or a consensus proc

29、ess. In addition, it does not contain requirements necessary for conformance to the Standard. This page is intentionally left blank.1 2018 NSF NSF/ANSI 336 2018 NSF/ANSI Standard for Sustainability Sustainability assessment for commercial furnishings fabric 1 General 1.1 Purpose This voluntary asses

30、sment tool is to provide guidance to suppliers, manufacturers, purchasers, fabricators, product specifiers, and users to assess the level of sustainability of commercial furnishings fabric. This Standard sets levels of conformance for commercial furnishings fabric to address environmental, economic

31、and social responsibility elements of sustainability. This Standard may be applied throughout select aspects of the commercial furnishings fabric supply chain as the scope of each sustainability parameter allows. 1.2 Scope This Standard provides pathways toward sustainability by establishing measura

32、ble criteria for multiple levels of achievement. It allows manufacturers flexibility in methods for conformance and certification. This Standard assesses product characteristics in the areas of material and component inputs, water and energy use, recycling practices and social accountability. This v

33、ersion of the Standard does not include specific criteria for calculating carbon footprint nor does it cover transportation. This Standard is applicable to commercial fabrics commonly used in public occupancy settings, such as office, hospitality, healthcare, and institutional interiors. These inclu

34、de but are not limited to upholstery, vertical fabric (furniture system, wall, drapery, and cubicle), and top of the bed fabrics. Fabrics may be formed by combining yarns, fibers, or filaments in a variety of ways including but not limited to woven, non-woven, knitted, bonded, felted, and composite

35、materials. This Standard is applicable to fabrics manufactured in one or multiple facilities, in one or multiple countries. While this Standard may be useful for applications beyond the commercial furnishings here outlined, the Standard is not intended to address fabrics developed for automotive, ap

36、parel, bedding, napery, toweling, military, medical or technical textiles applications. A fabric in its final form is assessed according to this Standard. Any alterations made after the point of assessment, for example after-market treatments, will nullify the certification. This Standard assumes co

37、mpliance with all applicable laws and regulations. Some criteria in the Standard address activities that are also subject to regulation by local, state, or federal authorities. However, the standard does not change the regulatory requirements nor does it prescribe how compliance is to be achieved. D

38、ocumentation of compliance with certain key regulations may be included in some sections of the Standard, but this in no way changes the underlying regulatory requirements. 2018 NSF NSF/ANSI 336 2018 2 1.3 Alternate products or materials While specific materials are stipulated in this Standard, prod

39、ucts or components that incorporate alternate materials shall be acceptable when it is verified that the product or component meets the applicable requirements of the Standard based on its end use. 1.4 Sustainability measurement 1.4.1 Terminology for sustainability parameters, credits, and points Cr

40、iteria for assessing a fabrics sustainability are defined for fiber sourcing, safety of material inputs, water conservation and quality, energy, air quality, recycling practices, and social accountability. These divisions are referred to as sustainability parameters. Within each of these parameters,

41、 there are prerequisite and/or optional credits, and within each credit, points are awarded as a measure of conformance. 1.4.2 Pre-requisite and optional credits Each sustainability parameter has pre-requisite and/or optional credits. All pre-requisites shall be met in order for a product to conform

42、 with the standard. Optional credits provide the manufacturer with additional means for further recognizing a fabrics sustainability. 1.4.3 Relative importance of sustainability parameters The maximum number of points that can be awarded to a fabric is 100. Half of the maximum points are based on th

43、e fabric composition, and half are based on how the fabric is made. The maximum number of points for each sustainability parameter is as follows: Fabric composition (50%): 20 pts Fiber Sourcing 30 pts Safety of Materials How the fabric is made (50%): 12 pts Water Conservation and Water Quality 12 pt

44、s Energy 2 pts Air Quality 12 pts Recycling Practices in Manufacturing 12 pts Social Accountability 1.4.4 Levels of achievement There are four levels of achievement to reflect increasing movement toward sustainability: Compliant, Silver, Gold, and Platinum. The level of achievement is based on a fab

45、rics total point value. A products total point value is the sum of points awarded for all sustainability parameters. The table below identifies the levels, with the associated credit points needed to achieve each level. 2018 NSF NSF/ANSI 336 2018 3 Table 1.1 Achievement levels Level Points required

46、Compliant 16 Silver 37 Gold 58 Platinum 79 maximum points 100 1.4.5 Measuring inputs from multiple sources Because multiple entities are commonly involved in the scope of manufacturing a commercial fabric, credits can apply to multiple entities; thus, points can be awarded for inputs throughout the

47、supply chain. The decision of whether to include suppliers and processes when calculating points depends upon the written scope for each sustainability parameter. Each applicable process that is listed in the scope shall be accounted for during the evaluation of a fabric. The awarding of points is w

48、eighted according to the relative importance of the inputs. For example, if multiple yarns are supplied from different suppliers then points for each yarn are awarded based on each yarns weight as a percentage of the finished fabric weight. 1.4.6 Instructions for rounding points Because the nature o

49、f fabric production commonly includes multiple suppliers and processes, fractions of points (or decimals) will be awarded for each credit. The following guidelines shall be used to minimize rounding errors: for each credit, the resulting point value should be expressed as a decimal. Do not round (For never-ending values, round to the thousandth place). for each sustainability parameter, the resulting point value should be expressed as a decimal rounded to the tenths place. Rounding is acceptable (e.g. round 10.05 to 10.1; 10.