IEEE C57 12.10-2017 Requirements for Liquid-Immersed Power Transformers《液体侵入式电力变压器用要求》.pdf

1、IEEE Standard Requirements for Liquid-Immersed Power Transformers IEEE Std C57.12.10-2017 (Revision of IEEE Std C57.12.10-2010) IEEE Power and Energy Society Sponsored by the Transformers Committee IEEE 3 Park Avenue New York, NY 10016-5997 USAIEEE Std C57.12.10-2017 (Revision of IEEE Std C57.12.10-

2、2010) IEEE Standard Requirements for Liquid-Immersed Power Transformers Sponsor IEEE Transformers Committee of the IEEE Power and Energy Society Approved 6 December 2017 IEEE-SA Standards BoardAbstract: This voluntary consensus standard sets forth the requirements for power transformer application.

3、This standard is intended to be used as a basis for performance, interchangeability, and safety of the equipment covered, and to assist in the proper selection of such equipment. This document is a product standard that covers certain electrical, dimensional, and mechanical characteristics of 50 Hz

4、and 60 Hz, liquid-immersed power transformers and autotransformers. Such power transformers may be remotely or integrally associated with either primary switchgear or substations, or both, for step-down or step-up purposes and base rated as follows: 833 kVA and above single-phase, 750 kVA and above

5、three-phase.This standard applies to all liquid-immersed power transformers and autotransformers that do not belong to the following types of apparatus: instrument transformers, step voltage and induction voltage regulators, arc-furnace transformers, rectifier transformers, specialty transformers, g

6、rounding transformers, mobile transformers, and mine transformers. Keywords: dimensional characteristics, electrical characteristics, IEEE C57.12.10, jacking, lifting, mechanical characteristics, on-load tap changer, power transformer, single-phase, three-phase The Institute of Electrical and Electr

7、onics Engineers, Inc. 3 Park Avenue, New York, NY 10016-5997, USA Copyright 2018 by The Institute of Electrical and Electronics Engineers, Inc. All rights reserved. Published 27 April 2018. Printed in the United States of America. IEEE is a registered trademark in the U.S. Patent fitness for a parti

8、cular purpose; non-infringement; and quality, accuracy, effectiveness, currency, or completeness of material. In addition, IEEE disclaims any and all conditions relating to: results; and workmanlike effort. IEEE standards documents are supplied “AS IS” and “WITH ALL FAULTS.” Use of an IEEE standard

9、is wholly voluntary. The existence of an IEEE standard does not imply that there are no other ways to produce, test, measure, purchase, market, or provide other goods and services related to the scope of the IEEE standard. Furthermore, the viewpoint expressed at the time a standard is approved and i

10、ssued is subject to change brought about through developments in the state of the art and comments received from users of the standard. In publishing and making its standards available, IEEE is not suggesting or rendering professional or other services for, or on behalf of, any person or entity nor

11、is IEEE undertaking to perform any duty owed by any other person or entity to another. Any person utilizing any IEEE Standards document, should rely upon his or her own independent judgment in the exercise of reasonable care in any given circumstances or, as appropriate, seek the advice of a compete

12、nt professional in determining the appropriateness of a given IEEE standard. IN NO EVENT SHALL IEEE BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO: PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS;

13、 OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE PUBLICATION, USE OF, OR RELIANCE UPON ANY STANDARD, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE AND REGARDL

14、ESS OF WHETHER SUCH DAMAGE W AS FORESEEABLE.4 Copyright 2018 IEEE. All rights reserved. Translations The IEEE consensus development process involves the review of documents in English only. In the event that an IEEE standard is translated, only the English version published by IEEE should be conside

15、red the approved IEEE standard. Official statements A statement, written or oral, that is not processed in accordance with the IEEE-SA Standards Board Operations Manual shall not be considered or inferred to be the official position of IEEE or any of its committees and shall not be considered to be,

16、 or be relied upon as, a formal position of IEEE. At lectures, symposia, seminars, or educational courses, an individual presenting information on IEEE standards shall make it clear that his or her views should be considered the personal views of that individual rather than the formal position of IE

17、EE. Comments on standards Comments for revision of IEEE Standards documents are welcome from any interested party, regardless of membership affiliation with IEEE. However, IEEE does not provide consulting information or advice pertaining to IEEE Standards documents. Suggestions for changes in docume

18、nts should be in the form of a proposed change of text, together with appropriate supporting comments. Since IEEE standards represent a consensus of concerned interests, it is important that any responses to comments and questions also receive the concurrence of a balance of interests. For this reas

19、on, IEEE and the members of its societies and Standards Coordinating Committees are not able to provide an instant response to comments or questions except in those cases where the matter has previously been addressed. For the same reason, IEEE does not respond to interpretation requests. Any person

20、 who would like to participate in revisions to an IEEE standard is welcome to join the relevant IEEE working group. Comments on standards should be submitted to the following address: Secretary, IEEE-SA Standards Board 445 Hoes Lane Piscataway, NJ 08854 USA Laws and regulations Users of IEEE Standar

21、ds documents should consult all applicable laws and regulations. Compliance with the provisions of any IEEE Standards document does not imply compliance to any applicable regulatory requirements. Implementers of the standard are responsible for observing or referring to the applicable regulatory req

22、uirements. IEEE does not, by the publication of its standards, intend to urge action that is not in compliance with applicable laws, and these documents may not be construed as doing so Copyrights IEEE draft and approved standards are copyrighted by IEEE under US and international copyright laws. Th

23、ey are made available by IEEE and are adopted for a wide variety of both public and private uses. These include both use, by reference, in laws and regulations, and use in private self-regulation, standardization, and the promotion of engineering practices and methods. By making these documents avai

24、lable for use and adoption by public authorities and private users, IEEE does not waive any rights in copyright to the documents.5 Copyright 2018 IEEE. All rights reserved. Photocopies Subject to payment of the appropriate fee, IEEE will grant users a limited, non-exclusive license to photocopy port

25、ions of any individual standard for company or organizational internal use or individual, non-commercial use only. To arrange for payment of licensing fees, please contact Copyright Clearance Center, Customer Service, 222 Rosewood Drive, Danvers, MA 01923 USA; +1 978 750 8400. Permission to photocop

26、y portions of any individual standard for educational classroom use can also be obtained through the Copyright Clearance Center. Updating of IEEE Standards documents Users of IEEE Standards documents should be aware that these documents may be superseded at any time by the issuance of new editions o

27、r may be amended from time to time through the issuance of amendments, corrigenda, or errata. An official IEEE document at any point in time consists of the current edition of the document together with any amendments, corrigenda, or errata then in effect. Every IEEE standard is subjected to review

28、at least every 10 years. When a document is more than 10 years old and has not undergone a revision process, it is reasonable to conclude that its contents, although still of some value, do not wholly reflect the present state of the art. Users are cautioned to check to determine that they have the

29、latest edition of any IEEE standard. In order to determine whether a given document is the current edition and whether it has been amended through the issuance of amendments, corrigenda, or errata, visit the IEEE Xplore at http:/ ieeexplore .ieee .or g/ or contact IEEE at the address listed previous

30、ly. For more information about the IEEE-SA or IEEEs standards development process, visit the IEEE-SA Website at http:/ standards .ieee .or g. Errata Errata, if any, for all IEEE standards can be accessed on the IEEE-SA Website at the following URL: http:/ standards .ieee .org/ findstds/ errata/ inde

31、x .html. Users are encouraged to check this URL for errata periodically. Patents Attention is called to the possibility that implementation of this standard may require use of subject matter covered by patent rights. By publication of this standard, no position is taken by the IEEE with respect to t

32、he existence or validity of any patent rights in connection therewith. If a patent holder or patent applicant has filed a statement of assurance via an Accepted Letter of Assurance, then the statement is listed on the IEEE- SA Website at http:/ standards .ieee .or g/ about/ sasb/ patcom/ patents .ht

33、ml. Letters of Assurance may indicate whether the Submitter is willing or unwilling to grant licenses under patent rights without compensation or under reasonable rates, with reasonable terms and conditions that are demonstrably free of any unfair discrimination to applicants desiring to obtain such

34、 licenses. Essential Patent Claims may exist for which a Letter of Assurance has not been received. The IEEE is not responsible for identifying Essential Patent Claims for which a license may be required, for conducting inquiries into the legal validity or scope of Patents Claims, or determining whe

35、ther any licensing terms or conditions provided in connection with submission of a Letter of Assurance, if any, or in any licensing agreements are reasonable or non-discriminatory. Users of this standard are expressly advised that determination of the validity of any patent rights, and the risk of i

36、nfringement of such rights, is entirely their own responsibility. Further information may be obtained from the IEEE Standards Association.6 Copyright 2018 IEEE. All rights reserved. Participants At the time this IEEE standard was completed, the Power Transformer Subcommittee Working Group had the fo

37、llowing membership: Gary Hoffman, Chair Brian Penny, Vice Chair Scott Digby, Secretary Hamid Abdelkamel Javier Arteaga Christopher Baumgartner Myron Bell Jeffrey Benach Neeraj Bhatia Wallace Binder William Boettger Arup Chakraborty Craig Colopy Marcos Ferreira Hugo Flores Anthony Franchitti George F

38、rimpong Rainer Frotscher Eduardo Garcia David Geibel Jeffrey Golarz Bill Griesacker Joshua Herz Joseph Holleran Jill Holmes Marion Jaroszewski John K. John Kurt Kaineder Ken Kampshoff Weijun Li Kumar Mani Robert Mayer Susan McNelly Emilio Morales-Cruz Ryan Musgrove Paul Mushill Shankar Nambi Anthony

39、 Natale Alan Peterson Oscar Pinon Donald Platts Zoilo Roldan Rodrigo Ronchi Amitabh Sarkar Roderick Sauls Ewald Schweiger Mark Shem-Tov Christopher Slattery Sanjib Som Thomas Spitzer Craig Stiegemeier Roy Su Kevin Sullivan Mark Tostrud Jason V arnell Rogerio V erdolin Dharam Vir Richard von Gemminge

40、n Sukhdev Walia Joe Watson Matthew Weisensee Trenton Williams Kipp Y ule Peter Zhao Waldemar Ziomek The following members of the individual balloting committee voted on this standard. Balloters may have voted for approval, disapproval, or abstention. Samuel Aguirre David Aho Stephen Antosz I. Antwei

41、ler Donald A yers Peter Balma Thomas Barnes Christopher Baumgartner Barry Beaster Robert Beavers Thomas Beckwith W.J. (Bill) Bergman Enrique Betancourt Steven Bezner Wallace Binder Thomas Bishop Thomas Blackburn Thomas Blair William Bloethe William Boettger Clarence Bradley Stephan Brauer Jeffrey Br

42、ogdon Derek Brown Demetrio Bucaneg Jr. William Byrd Paul Cardinal Michael Champagne Michael Chirico C. Clair Claiborne Kurt Clemente Craig Colopy Randall Crellin John Crouse Randall Cunico Willaim Darovny Glenn Davis Frank Decesaro Scott Digby Dieter Dohnal Gary Donner Ahmed El Sherbieny Namal Ferna

43、ndo Joseph Foldi Bruce Forsyth Dale Fredrickson George Frimpong Shawn Galbraith Ali Ghafourian Ramsis Girgis Jalal Gohari Edwin Goodwin James Graham Stephen Grier Randall Groves Bal Gupta Attila Gyore John Harley J. Harlow Jeffrey Hartenberger Roger Hayes Joshua Herz Werner Hoelzl Gary Hoffman Jill Holmes