IEC 62505-3-2-2009 Railway applications - Fixed installations - Particular requirements for a c switchgear - Part.3-2 Measurement control and protection devices.pdf

1、 IEC 62505-3-2 Edition 1.0 2009-03 INTERNATIONAL STANDARD NORME INTERNATIONALE Railway applications Fixed installations Particular requirements for a.c. switchgear Part 3-2: Measurement, control and protection devices for specific use in a.c. traction systems Single-phase current transformers Applic

2、ations ferroviaires Installations fixes Exigences particulires pour appareillage courant alternatif Partie 3-2: Dispositifs de mesure, de commande et de protection pour usage spcifique dans les systmes de traction courant alternatif Transformateurs de courant monophass IEC 62505-3-2:2009 THIS PUBLIC

3、ATION IS COPYRIGHT PROTECTED Copyright 2009 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing f

4、rom either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further informati

5、on. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de la CEI ou du Comit national d

6、e la CEI du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de la CEI de votre pays de rsidence. IEC Central Office 3, rue de Varemb CH-1

7、211 Geneva 20 Switzerland Email: inmailiec.ch Web: www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publications The t

8、echnical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Catalogue of IEC publications: www.iec.ch/searchpub The IEC on-line Catalogue enables you to search by a variety o

9、f criteria (reference number, text, technical committee,). It also gives information on projects, withdrawn and replaced publications. IEC Just Published: www.iec.ch/online_news/justpub Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. A

10、vailable on-line and also by email. Electropedia: www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions in English and French, with equivalent terms in additional languages. Also known as the International Elect

11、rotechnical Vocabulary online. Customer Service Centre: www.iec.ch/webstore/custserv If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service Centre FAQ or contact us: Email: csciec.ch Tel.: +41 22 919 02 11 Fax: +41 22 919 03 00 A propos

12、 de la CEI La Commission Electrotechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications CEI Le contenu technique des publications de

13、 la CEI est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Catalogue des publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm Le Catalogue en-ligne de la CEI vous permet deffectuer des recherches en utilisant di

14、ffrents critres (numro de rfrence, texte, comit dtudes,). Il donne aussi des informations sur les projets et les publications retires ou remplaces. Just Published CEI: www.iec.ch/online_news/justpub Restez inform sur les nouvelles publications de la CEI. Just Published dtaille deux fois par mois les

15、 nouvelles publications parues. Disponible en-ligne et aussi par email. Electropedia: www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 20 000 termes et dfinitions en anglais et en franais, ainsi que les termes quivalents dans le

16、s langues additionnelles. Egalement appel Vocabulaire Electrotechnique International en ligne. Service Clients: www.iec.ch/webstore/custserv/custserv_entry-f.htm Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions, visitez le FAQ du Service clients ou cont

17、actez-nous: Email: csciec.ch Tl.: +41 22 919 02 11 Fax: +41 22 919 03 00 IEC 62505-3-2 Edition 1.0 2009-03 INTERNATIONAL STANDARD NORME INTERNATIONALE Railway applications Fixed installations Particular requirements for a.c. switchgear Part 3-2: Measurement, control and protection devices for specif

18、ic use in a.c. traction systems Single-phase current transformers Applications ferroviaires Installations fixes Exigences particulires pour appareillage courant alternatif Partie 3-2: Dispositifs de mesure, de commande et de protection pour usage spcifique dans les systmes de traction courant altern

19、atif Transformateurs de courant monophass INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE J ICS 45.060 PRICE CODE CODE PRIX ISBN 2-8318-1030-8 Registered trademark of the International Electrotechnical Commission Marque dpose de la Commission Electrotechnique Int

20、ernationale 2 62505-3-2 IEC:2009 CONTENTS FOREWORD.3 INTRODUCTION.5 1 Scope.6 2 Normative references6 3 Terms and definitions .6 4 Service conditions.7 5 Characteristics and use 7 6 Rating and design requirements7 7 Short circuit conditions on the primary side .7 8 Particular design and construction

21、 characteristics .7 8.1 Pollution 7 8.2 Floating potentials and earthing .8 8.3 Electromagnetic compatibility.8 8.4 Connections 8 8.5 Information to be given by the purchaser8 8.6 Information to be given by the supplier.8 9 Other requirements.9 62505-3-2 IEC:2009 3 INTERNATIONAL ELECTROTECHNICAL COM

22、MISSION _ RAILWAY APPLICATIONS FIXED INSTALLATIONS PARTICULAR REQUIREMENTS FOR AC SWITCHGEAR Part 3-2: Measurement, control and protection devices for specific use in a.c. traction systems Single-phase current transformers FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwid

23、e organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activ

24、ities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject

25、dealt with may participate in this preparatory work. International, governmental and non- governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determ

26、ined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committ

27、ees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which t

28、hey are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication

29、 and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment declared to be in conformity with an IEC Publication. 6) All users should ensure that t

30、hey have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature

31、 whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced p

32、ublications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International

33、 Standard IEC 62505-3-2 has been prepared by IEC technical committee 9: Electrical equipment and systems for railways. This standard is based on EN 50152-3-2. The text of this standard is based on the following documents: FDIS Report on voting 9/1222/FDIS 9/1235/RVD Full information on the voting fo

34、r the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. 4 62505-3-2 IEC:2009 A list of all parts of IEC 62505 series, under the general title Railway applications Fixed ins

35、tallations Particular requirements for a.c. switchgear, can be found on the IEC website. The committee has decided that the contents of this publication will remain unchanged until the maintenance result dateindicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the speci

36、fic publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. 62505-3-2 IEC:2009 5 INTRODUCTION Part 3 of IEC 62505 series, “Railway applications Fixed installations Particular requirements for a.c. switchgear“, concerning the measurement,

37、control and protection devices for specific use in a.c. traction systems, comprises: IEC 62505-3-1: Application guide (informative document) IEC 62505-3-2: Single-phase current transformers (normative document) IEC 62505-3-3: Single-phase inductive voltage transformers (normative document) This Inte

38、rnational Standard applies when the equipment is concerned with the specified characteristics. The requirements contained in this standard complement those given in IEC 60044-1:1996, Amendment 1 (2000), Amendment 2 (2002). 6 62505-3-2 IEC:2009 RAILWAY APPLICATIONS FIXED INSTALLATIONS PARTICULAR REQU

39、IREMENTS FOR AC SWITCHGEAR Part 3-2: Measurement, control and protection devices for specific use in a.c. traction systems Single-phase current transformers 1 Scope This part of IEC 62505 gives particular requirements for current transformers used in a.c. single-phase railway applications, fixed ins

40、tallations. This International Standard applies to current transformers used at traction voltages and frequencies according to IEC 60850. The main uses of these current transformers are: measurement; protection. 2 Normative references The following referenced documents are indispensable for the appl

41、ication of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60044-1:1996, Instrument transformers Part 1: Current transformers Amendment 1 (2000), Amendment 2 (2002) IEC

42、60529:2001, Degrees of protection provided by enclosures (IP Code) IEC 60850, Railway applications Supply voltages of traction systems IEC 62236 (all parts), Railway applications Electromagnetic compatibility IEC 62497-1, Railway applications Insulation coordination Part 1: Basic requirements Cleara

43、nces and creepage distances for all electrical and electronic equipment IEC 62505 (all parts), Railway applications Fixed installations Particular requirements for a.c. switchgear 3 Terms and definitions For the purposes of this document, the terms and definitions given in IEC 62505-1 and in IEC 600

44、44-1 apply. 62505-3-2 IEC:2009 7 4 Service conditions Where the equipment described in this part of the standard is mounted on circuit-breakers according to IEC 62505-1, then the service conditions of that standard apply. Where they are separately mounted and are used in association with switchgear

45、then the same service conditions as the switchgear apply. 5 Characteristics and use The current transformer shall be: a) either mounted inside the circuit-breaker specified in IEC 62505-1 and accommodated within special bushings on the circuit-breaker; technical requirements of this IEC 62505-3-2 ap

46、ply together with the construction and test requirements (as applicable) of IEC 62505-1; b) or separately mounted free standing; technical requirements of this IEC 62505-3-2 apply. 6 Rating and design requirements Clauses 4 and 5 of IEC 60044-1:1996 apply with the following exceptions: In Subclause

47、4.2 the words “but the preferred value is 5 A.” shall be replaced by “but the preferred values are 1 A or 5 A.” In Clause 5 the entire Subclause 5.1.1 shall be replaced by: 5.1.1 Rated insulation levels for the primary winding Current transformers covered by this standard shall have the same insulat

48、ion ratings and test values as the equipment into which they are installed. See Table 1 of IEC 62505-1 and IEC 62505-2. Free standing current transformers shall meet the same requirements. Subclause 5.1.6 of IEC 60044-1 is valid unless inconsistent with 8.1 of this Standard. 7 Short circuit conditio

49、ns on the primary side The following requirements, additional to those of IEC 60044-1:1996, apply: Current transformers shall have a rated short time withstand current for a duration of 1 s, with a peak value of 2,5 p.u. in accordance with the requirements of IEC 60044-1:1996. NOTE These events occur often and special attention should be paid to