PC37.237D0.8, Apr 2018 - IEEE Draft Standard Requirements for Time Tags Created by Intelligent Electronic Devices - COMTAG(TM) .pdf

1、PC37.237/D0.8, April 2018 Draft Standard for Requirements for Time Tags Created by Intelligent Electronic DevicesCOMTAG PC37.237/D0.8 1 Draft Standard for Requirements for 2 Time Tags Created by Intelligent 3 Electronic DevicesCOMTAG 4 Sponsor 5 6 Power System Relaying Committee and the Substations

2、Committee 7 of the 8 IEEE Power and Energy Society 9 10 11 Approved 12 13 IEEE-SA Standards Board 14 15 Copyright 2016 by The Institute of Electrical and Electronics Engineers, Inc. 16 Three Park Avenue 17 New York, New York 10016-5997, USA 18 All rights reserved. 19 This document is an unapproved d

3、raft of a proposed IEEE Standard. As such, this document is subject to 20 change. USE AT YOUR OWN RISK! IEEE copyright statements SHALL NOT BE REMOVED from draft 21 or approved IEEE standards, or modified in any way. Because this is an unapproved draft, this document 22 must not be utilized for any

4、conformance/compliance purposes. Permission is hereby granted for officers 23 from each IEEE Standards Working Group or Committee to reproduce the draft document developed by 24 that Working Group for purposes of international standardization consideration. IEEE Standards 25 Department must be infor

5、med of the submission for consideration prior to any reproduction for 26 international standardization consideration (stds.iprieee.org). Prior to adoption of this document, in 27 whole or in part, by another standards development organization, permission must first be obtained from 28 the IEEE Stand

6、ards Department (stds.iprieee.org). When requesting permission, IEEE Standards 29 Department will require a copy of the standard development organizations document highlighting the use 30 of IEEE content. Other entities seeking permission to reproduce this document, in whole or in part, must 31 also

7、 obtain permission from the IEEE Standards Department. 32 IEEE Standards Department 33 445 Hoes Lane 34 Piscataway, NJ 08854, USA 35 36PC37.237/D0.8, April 2018 Draft Standard for Requirements for Time Tags Created by Intelligent Electronic DevicesCOMTAG Abstract: Common requirements for associating

8、 time tags with data items recorded or 1 transmitted by Intelligent Electronic Devices (IEDs) are established in this standard. The standard 2 specifies time-tag attributes and requirements for describing time-tag accuracy. 3 4 Keywords: COMTAG, IED, IEEE PC37.237, IRIG-B, time stamp, time synchroni

9、zation, 5 time tag 6 7 8The Institute of Electrical and Electronics Engineers, Inc. 3 Park Avenue, New York, NY 10016-5997, USA Copyright 2016 by The Institute of Electrical and Electronics Engineers, Inc. All rights reserved. Published . Printed in the United States of America. IEEE is a registered

10、 trademark in the U.S. Patent fitness 19 for a particular purpose; non-infringement; and quality, accuracy, effectiveness, currency, or completeness 20 of material. In addition, IEEE disclaims any and all conditions relating to: results; and workmanlike effort. 21 IEEE standards documents are suppli

11、ed “AS IS” and “WITH ALL FAULTS.” 22 Use of an IEEE standard is wholly voluntary. The existence of an IEEE standard does not imply that there 23 are no other ways to produce, test, measure, purchase, market, or provide other goods and services related 24 to the scope of the IEEE standard. Furthermor

12、e, the viewpoint expressed at the time a standard is approved 25 and issued is subject to change brought about through developments in the state of the art and comments 26 received from users of the standard. 27 In publishing and making its standards available, IEEE is not suggesting or rendering pr

13、ofessional or other 28 services for, or on behalf of, any person or entity nor is IEEE undertaking to perform any duty owed by any 29 other person or entity to another. Any person utilizing any IEEE Standards document, should rely upon his 30 or her own independent judgment in the exercise of reason

14、able care in any given circumstances or, as 31 appropriate, seek the advice of a competent professional in determining the appropriateness of a given 32 IEEE standard. 33 IN NO EVENT SHALL IEEE BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, 34 EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING

15、, BUT NOT LIMITED TO: 35 PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; 36 OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, 37 WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR 38 OTHERWISE) ARISING IN ANY WAY OUT OF THE PUBL

16、ICATION, USE OF, OR RELIANCE 39 UPON ANY STANDARD, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE AND 40 REGARDLESS OF WHETHER SUCH DAMAGE WAS FORESEEABLE. 41 Translations 42 The IEEE consensus development process involves the review of documents in English only. In the event 43 that an IEEE stan

17、dard is translated, only the English version published by IEEE should be considered the 44 approved IEEE standard. 45 46PC37.237/D0.8, April 2018 Draft Standard for Requirements for Time Tags Created by Intelligent Electronic DevicesCOMTAG Official statements 1 A statement, written or oral, that is

18、not processed in accordance with the IEEE-SA Standards Board 2 Operations Manual shall not be considered or inferred to be the official position of IEEE or any of its 3 committees and shall not be considered to be, or be relied upon as, a formal position of IEEE. At lectures, 4 symposia, seminars, o

19、r educational courses, an individual presenting information on IEEE standards shall 5 make it clear that his or her views should be considered the personal views of that individual rather than the 6 formal position of IEEE. 7 Comments on standards 8 Comments for revision of IEEE Standards documents

20、are welcome from any interested party, regardless of 9 membership affiliation with IEEE. However, IEEE does not provide consulting information or advice 10 pertaining to IEEE Standards documents. Suggestions for changes in documents should be in the form of a 11 proposed change of text, together wit

21、h appropriate supporting comments. Since IEEE standards represent a 12 consensus of concerned interests, it is important that any responses to comments and questions also receive 13 the concurrence of a balance of interests. For this reason, IEEE and the members of its societies and 14 Standards Coo

22、rdinating Committees are not able to provide an instant response to comments or questions 15 except in those cases where the matter has previously been addressed. For the same reason, IEEE does not 16 respond to interpretation requests. Any person who would like to participate in revisions to an IEE

23、E 17 standard is welcome to join the relevant IEEE working group. 18 Comments on standards should be submitted to the following address: 19 Secretary, IEEE-SA Standards Board 20 445 Hoes Lane 21 Piscataway, NJ 08854 USA 22 Laws and regulations 23 Users of IEEE Standards documents should consult all

24、applicable laws and regulations. Compliance with 24 the provisions of any IEEE Standards document does not imply compliance to any applicable regulatory 25 requirements. Implementers of the standard are responsible for observing or referring to the applicable 26 regulatory requirements. IEEE does no

25、t, by the publication of its standards, intend to urge action that is not 27 in compliance with applicable laws, and these documents may not be construed as doing so 28 Copyrights 29 IEEE draft and approved standards are copyrighted by IEEE under U.S. and international copyright laws. 30 They are ma

26、de available by IEEE and are adopted for a wide variety of both public and private uses. These 31 include both use, by reference, in laws and regulations, and use in private self-regulation, standardization, 32 and the promotion of engineering practices and methods. By making these documents availab

27、le for use and 33 adoption by public authorities and private users, IEEE does not waive any rights in copyright to the 34 documents. 35 Photocopies 36 Subject to payment of the appropriate fee, IEEE will grant users a limited, non-exclusive license to 37 photocopy portions of any individual standard

28、 for company or organizational internal use or individual, 38 non-commercial use only. To arrange for payment of licensing fees, please contact Copyright Clearance 39 Center, Customer Service, 222 Rosewood Drive, Danvers, MA 01923 USA; +1 978 750 8400. Permission 40 to photocopy portions of any indi

29、vidual standard for educational classroom use can also be obtained 41 through the Copyright Clearance Center. 42PC37.237/D0.8, April 2018 Draft Standard for Requirements for Time Tags Created by Intelligent Electronic DevicesCOMTAG Updating of IEEE Standards documents 1 Users of IEEE Standards docum

30、ents should be aware that these documents may be superseded at any time 2 by the issuance of new editions or may be amended from time to time through the issuance of amendments, 3 corrigenda, or errata. An official IEEE document at any point in time consists of the current edition of the 4 document

31、together with any amendments, corrigenda, or errata then in effect. 5 Every IEEE standard is subjected to review at least every ten years. When a document is more than ten 6 years old and has not undergone a revision process, it is reasonable to conclude that its contents, although 7 still of some v

32、alue, do not wholly reflect the present state of the art. Users are cautioned to check to 8 determine that they have the latest edition of any IEEE standard. 9 In order to determine whether a given document is the current edition and whether it has been amended 10 through the issuance of amendments,

33、 corrigenda, or errata, visit the IEEE-SA Website at 11 http:/ieeexplore.ieee.org/xpl/standards.jsp or contact IEEE at the address listed previously. For more 12 information about the IEEE SA or IEEEs standards development process, visit the IEEE-SA Website at 13 http:/standards.ieee.org. 14 Errata

34、15 Errata, if any, for all IEEE standards can be accessed on the IEEE-SA Website at the following URL: 16 http:/standards.ieee.org/findstds/errata/index.html. Users are encouraged to check this URL for errata 17 periodically. 18 Patents 19 Attention is called to the possibility that implementation o

35、f this standard may require use of subject matter 20 covered by patent rights. By publication of this standard, no position is taken by the IEEE with respect to 21 the existence or validity of any patent rights in connection therewith. If a patent holder or patent applicant 22 has filed a statement

36、of assurance via an Accepted Letter of Assurance, then the statement is listed on the 23 IEEE-SA Website at http:/standards.ieee.org/about/sasb/patcom/patents.html. Letters of Assurance may 24 indicate whether the Submitter is willing or unwilling to grant licenses under patent rights without 25 com

37、pensation or under reasonable rates, with reasonable terms and conditions that are demonstrably free of 26 any unfair discrimination to applicants desiring to obtain such licenses. 27 Essential Patent Claims may exist for which a Letter of Assurance has not been received. The IEEE is not 28 responsi

38、ble for identifying Essential Patent Claims for which a license may be required, for conducting 29 inquiries into the legal validity or scope of Patents Claims, or determining whether any licensing terms or 30 conditions provided in connection with submission of a Letter of Assurance, if any, or in

39、any licensing 31 agreements are reasonable or non-discriminatory. Users of this standard are expressly advised that 32 determination of the validity of any patent rights, and the risk of infringement of such rights, is entirely 33 their own responsibility. Further information may be obtained from th

40、e IEEE Standards Association 34PC37.237/D0.8, April 2018 Draft Standard for Requirements for Time Tags Created by Intelligent Electronic DevicesCOMTAG Copyright 2016 IEEE. All rights reserved. This is an unapproved IEEE Standards Draft, subject to change. vi Participants 1 At the time this draft sta

41、ndard was completed, the H4/C4 Working Group had the following membership: 2 Bill Dickerson, Chair, Power System Relaying Committee H3 3 Jim Hackett, Vice Chair, Power System Relaying Committee H3 4 Marc Lacroix, Chair, Substations Committee C4 5 6 Participant1 7 Participant2 8 Participant3 9 Partic

42、ipant4 10 Participant5 11 Participant6 12 Participant7 13 Participant8 14 Participant9 15 16 The following members of the balloting committee voted on this standard. Balloters 17 may have voted for approval, disapproval, or abstention. 18 To be supplied by IEEE 19 Balloter1 20 Balloter2 21 Balloter3

43、 22 Balloter4 23 Balloter5 24 Balloter6 25 Balloter7 26 Balloter8 27 Balloter9 28 29 When the IEEE-SA Standards Board approved this standard on , it had the following 30 membership: 31 To be supplied by IEEE 32 , Chair 33 , Vice Chair 34 , Past Chair 35 Konstantinos Karachalios, Secretary 36 SBMember1 37 SBMember2 38 SBMember3 39 SBMember4 40 SBMember5 41 SBMember6 42 SBMember7 43 SBMember8 44 SBMember9 45 *Member Emeritus 46 47