ImageVerifierCode 换一换
格式:PDF , 页数:2 ,大小:53.52KB ,
资源ID:286825      下载积分:5000 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
注意:如需开发票,请勿充值!
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【http://www.mydoc123.com/d-286825.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: 微信登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(ASTM D2943 - 02(2012) Standard Test Method for Aluminum Scratch of 1,1,1-Trichloroethane to Determine Stability (Withdrawn 2017).pdf)为本站会员(李朗)主动上传,麦多课文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文库(发送邮件至master@mydoc123.com或直接QQ联系客服),我们立即给予删除!

ASTM D2943 - 02(2012) Standard Test Method for Aluminum Scratch of 1,1,1-Trichloroethane to Determine Stability (Withdrawn 2017).pdf

1、Designation: D2943 02 (Reapproved 2012)Standard Test Method forAluminum Scratch of 1,1,1-Trichloroethane to DetermineStability1This standard is issued under the fixed designation D2943; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revisio

2、n, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This is a screening test method to determine if sufficientinhibitors are present in 1,1,1-trichloroetha

3、ne to provide atleast minimal stability in the presence of aluminum.1.2 Solvent passing this test method may not be stable forall applications.1.3 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standar

4、d to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use. A specific hazardstatement is given in Section 6.2. Summary of Test Method2.1 A cleaned, degreased, dry metal coupon of aluminumalloy is immersed in inhibited 1,1,1-trichl

5、oroethane andscratched while in the solvent. After sufficient time has elapsedto allow any reaction to occur, the presence or absence ofbubbling, solvent discoloration, or dark resinous material isnoted. The 1,1,1-trichloroethane is sufficiently inhibited only ifnone of these conditions is observed.

6、3. Significance and Use3.1 The degradation of insufficiently stabilized 1,1,1-trichloroethane, in the presence of aluminum, results in theformation of hydrochloric acid and polymeric residue. Thus, ifsuch degradation is allowed to continue, the aluminum will becorroded and the 1,1,1-trichloroethane

7、rendered unusable. Thepresence of free water invalidates this test method.3.2 This test method can be used to determine if 1,1,1-trichloroethane is sufficiently stabilized to inhibit reaction withaluminum or aluminum alloys. Solvent passing this testmethod still may not be stable for all application

8、s. Consult aproducer for use applications.3.3 Aluminum should not be used as a material of construc-tion for pumps, tanks, pipelines, valves, spray equipment, orother handling equipment used for chlorinated solvents. Prop-erly stabilized halogenated solvents are, however, commonlyused in cleaning al

9、uminum and other sensitive metals.4. Apparatus4.1 Aluminum Sheet Metal, designated ASTM Alloy 1100(UNS No. A91100),20.016 to 0.040 in. (0.4 to 1 mm) thick.4.2 Mild Steel Metal Object, such as an ice pick sharpenedto lead pencil-sized point.5. Preparation of Aluminum Coupon5.1 Degrease an aluminum co

10、upon, 1 by 1 in., (2.5 by 2.5cm) by rinsing in a commercial grade of solvent such asperchloroethylene, trichloroethylene, or 1,1,1-trichloroethane.Hand-sand both sides of the aluminum coupon lightly with afine emery cloth, and rinse the coupon again. The surfaceshould be bright and free of haze.6. H

11、azards6.1 This test method should be performed in a fume hood.Insufficiently inhibited solvent can react with aluminum toform hydrogen and hydrogen chloride gases. Solvent vaporsare also present. Their release to the atmosphere must beminimized.7. Procedure7.1 Conduct this test method at room temper

12、ature. Measure50 mL of inhibited 1,1,1-trichloroethane into a clean solvent-rinsed glass beaker. Place a freshly prepared aluminum couponin the solvent sample in a horizontal position on the bottom ofthe beaker. Scratch (Note 1) the top surface of the submergedaluminum coupon with a sharply pointed

13、mild steel instrument.Make three scratches approximately equally spaced and 0.005in. (0.1 mm) deep in one direction. Then make three additionalscratches at right angles to the original three (Note 2). Observethe aluminum coupon after 10 min and again after1hhaselapsed. In the event that continued de

14、composition occurs after1This test method is under the jurisdiction of ASTM Committee D26 onHalogenated Organic Solvents and Fire Extinguishing Agents and is the directresponsibility of Subcommittee D26.04 on Test Methods.Current edition approved March 1, 2012. Published May 2012. Originallyapproved

15、 in 1971 as D294371 T. Last previous edition approved in 2007 as D294302 (2007). DOI: 10.1520/D2943-02R12.2Annual Book of ASTM Standards, Vol 02.02.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesNOTICE: This standard has either been s

16、uperseded and replaced by a new version or withdrawn.Contact ASTM International (www.astm.org) for the latest information11 h, add water to stop the reaction, remove the aluminumcoupon, and discard the solvent in a solvent container toprevent evaporation.NOTE 1The scratch should be a lateral scrape

17、rather than a verticalperforation.NOTE 2Scratches are to appear as follows:8. Report8.1 For each test method, report observations as follows:8.1.1 Passes/no reaction.8.1.2 Fails/the appearance of gas bubbles, color formation,or metal corrosion at the edge of the scratch marks are evidenceof failure

18、to pass the test method.8.2 The solvent should be considered sufficiently stabilizedfor many uses in the presence of aluminum or aluminum alloysonly if no reaction occurs. The absence of reactivity in this testmethod may not indicate stability for all applications.9. Precision and Bias9.1 Only visua

19、l observations are reported. No precision andbias statements can be made.10. Keywords10.1 aluminum; aluminum scratch test; inhibitors; stabilitytest; 1,1,1-trichloroethaneASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedi

20、n this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and mu

21、st be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of th

22、eresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C70

23、0, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).D2943 02 (2012)2

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1