ASTM F2673 - 08 Standard Safety Specification for Special Tip-Resistant Movable Soccer Goals (Withdrawn 2017).pdf

1、Designation: F2673 08Standard Safety Specification forSpecial Tip-Resistant Movable Soccer Goals1This standard is issued under the fixed designation F2673; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision.

2、A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers safety requirements aimed atproviding for safer use of soccer goals and reducing injuriesand fatalities.1.2

3、 This specification addresses the risk of accidental tipover or pull over of soccer goals.1.3 This specification applies only to movable goals whoseinside measurements are 612 to 8 ft (2 to 2.4 m) high and 18 to24 ft (5.5 to 7.3 m) wide.1.4 This specification applies only to movable goals meet-ing a

4、ll criteria in Guide F1938 and Safety and PerformanceSpecification F2056 and, in addition, meets criteria for tipresistance before installation.1.5 This specification covers special tip-resistant goals thatare intended to complement standard goals meeting GuideF1938 and Safety and Performance Specif

5、ication F2056. Thesegoals are designed to provide some additional degree of safetyif, by accident, they are not tied down or tied down incorrectly.1.6 This specification simulates two boys up to twelve yearsof age swinging together from the X-bar.NOTE 1Injury data supplied to the committee indicates

6、 that approxi-mately 75 % (74 %) of the fatalities (1979-2003) were three to twelveyears of age.1.7 The values stated in inch-pound units are to be regardedas standard. The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considere

7、d standard.1.8 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. R

8、eferenced Documents2.1 ASTM Standards:2F1938 Guide for Safer Use of Movable Soccer GoalsF2056 Safety and Performance Specification for SoccerGoals3. Terminology3.1 DefinitionsSee Guide F1938 and Safety and Perfor-mance Specification F2056 for definitions.4. Safety Requirements4.1 Soccer goals shall

9、be subjected to the test outline inSection 5 and shall neither tilt over nor refuse to return to itsoriginal vertical position.4.2 Tests shall be applied to soccer goals in their originalunrestrained (no tie-down) condition.4.3 Tests shall be repeated three times.4.4 Tests shall be applied only to m

10、ovable goals.4.5 Soccer goals shall then meet all testing criteria,instructions, and labeling listed in Safety and PerformanceSpecification F2056 including anchoring.5. Stability Test5.1 Goals shall be set upon a flat, outdoor (earth) surface.5.2 Two weights shall be placed 1.5 ft (0.46 m) on each s

11、ideof the center of the X-bar of the goal (Fig. 1).5.3 The weights shall be composed of bags of sand weigh-ing 110 6 2lb(506 1 kg) each.NOTE 2The weights (5.3) are selected to simulate two twelve-year-oldboys. (Physical characteristics of children as related to death and injury forconsumer product s

12、afety design and use, 95th percentile, twelve-year-oldmale, 109 lb (49 kg).)5.4 The weighed bags shall be tied firmly to the X-bar with12-in. (1.3-cm) ropes.5.5 Weights shall dangle from the rope and each bag spaced(vertically downward) so that the center of the bag is 12 6 1in. (30.5 6 2.5 cm) from

13、 the X-bar.1This specification is under the jurisdiction of ASTM Committee F15 onConsumer Products and is the direct responsibility of Subcommittee F15.43 onSoccer Goal Safety.Current edition approved Feb. 1, 2008. Published February 2008. DOI: 10.1520/F2673-08.2For referenced ASTM standards, visit

14、the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959.

15、 United StatesNOTICE: This standard has either been superseded and replaced by a new version or withdrawn.Contact ASTM International (www.astm.org) for the latest information15.6 Weights shall be simultaneously displaced at a 30 anglefrom the vertical position (perpendicular to the cross-bar) withro

16、pe extended, held for 10 6 2 s, released, and allowed toswing freely (Fig. 2).5.7 The test shall be repeated with the weights swung froma 30 angle on the opposite side.6. Labels6.1 No product covered by this specification and producedafter the approval date shall, by label, marking, or other means,i

17、ndicate compliance unless it conforms to all requirementsherein.6.2 Soccer goals meeting this specification shall be labeled“Special Tilt-Resistant Goal Meeting ASTM F2673.”7. Keywords7.1 soccer goal; tilt-resistant goalFIG. 1 Two Weights Applied at the Center of the X-Bar of the Goal and Spaced 3 f

18、t (0.9 m) ApartFIG. 2 Weights Simultaneously Displaced at a 30 Angle from the Vertical Position, Held for 10 6 2 s, Released, and Allowed to SwingFreelyF2673 082ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this sta

19、ndard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be revi

20、ewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsib

21、le technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Co

22、nshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 083