ASTM D6787 D6787M-02(2017) Standard Specification for Repositionable Note Pad.pdf

1、Designation: D6787/D6787M 02 (Reapproved 2017)Standard Specification forRepositionable Note Pad1This standard is issued under the fixed designation D6787/D6787M; the number immediately following the designation indicates theyear of original adoption or, in the case of revision, the year of last revi

2、sion. A number in parentheses indicates the year of lastreapproval. A superscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S. Department of Defense.1. Scope1.1 This specification covers pads of reposit

3、ionable,colored, note paper. Each sheet has a strip of pressure-sensitiveadhesive on the back side.1.2 The values stated in either SI or inch-pound units are tobe regarded separately as standard. The values stated in eachsystem are not exact equivalents; therefore, each system mustbe used independen

4、tly, without combining values in any way.1.3 The following safety hazards caveat pertains only toSection 14, Performance Requirements. This standard does notpurport to address all of the safety concerns, if any, associatedwith its use. It is the responsibility of the user of this standardto establis

5、h appropriate safety and health practices anddetermine the applicability of regulatory requirements prior touse.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of

6、International Standards, Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade (TBT) Committee.2. Referenced Documents2.1 ASTM Standards:2D3715/D3715M Practice for Quality Assurance of Pressure-Sensitive TapesD3951 Practice for Commercial PackagingD4332 Practi

7、ce for Conditioning Containers, Packages, orPackaging Components for Testing2.2 TAPPI Test Methods:3T 410 Grammage of Paper and Paperboard (Weight per UnitArea)T411Thickness (caliper) of Paper, Paper Board, and Com-bined Board2.3 Executive Orders:4Executive Order 13101 Greening the Government Throug

8、hWaste Prevention, Recycling, and Federal Acquisition,September 16, 19982.4 Federal Specification:5Code of Federal Regulations, 16 CFR Part 1500.3 Defini-tions of Toxic and Hazardous MaterialsU.S. Government CID A-A-2546 Pad, Writing Paper (Repo-sitionable)2.5 ISO Standard:ISO 9002 Quality Systems M

9、odel for Quality Assurance inProduction and Installation62.6 Other Standards:Coalition of Northeastern Governors (CONEG) Model Tox-ics Legislation73. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 flaggingthe lifting of an edge of a repositionablenote from paper when the note an

10、d paper are wrapped arounda cylinder.3.1.2 multiple liftthe condition in which removal of thetop sheet on a pad of notes causes the unintentional removal ofa second sheet.1This specification is under the jurisdiction of ASTM Committee D10 onPackaging and is the direct responsibility of Subcommittee

11、D10.14 on Tape andLabels.Current edition approved Sept. 1, 2017. Published September 2017. Originallyapproved in 2002. Last previous edition approved in 2012 as D6787/D6787M 02 (2012)1. DOI: 10.1520/D6787_D6787M-02R17.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact AS

12、TM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from Technical Association of the Pulp and Paper Industry (TAPPI),15 Technology Parkway South, Norcross, GA 30092, http:/www.tappi.o

13、rg.4Available from The White House Publications Office, New Executive OfficeBuilding, White House, Washington, DC 20500, Att: Publications.5Available from U.S. Government Printing Office Superintendent of Documents,732 N. Capitol St., NW, Mail Stop: SDE, Washington, DC 20401, http:/www.access.gpo.go

14、v.6Available from American National Standards Institute (ANSI), 25 W. 43rd St.,4th Floor, New York, NY 10036, http:/www.ansi.org.7Available from the Toxins in Packaging Clearinghouse, c/o the Council of StateGovernments, 2760 Research Park Drive, P.O. Box 11910, Lexington, KY405781910.Copyright ASTM

15、 International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Stand

16、ards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.13.1.3 postconsumer materialsa material or finished prod-uct that has served its intended use and has been discarded fordisposal or recovery, having completed its life as a consumerite

17、m. Postconsumer material is a part of the broader category ofrecovered material (see U.S. Executive Order 13101, section203).3.1.4 recovered materialswaste materials and by-productsthat have been recovered or diverted from solid waste, but suchterm does not include those materials and by-products ge

18、ner-ated from, and commonly reused within, an original manufac-turing process (see U.S. Executive Order 13101, section 205).4. Significance and Use4.1 Repositionable note pads consist of individual sheets ofpaper with an adhesive strip on one edge. The adhesive willtemporarily hold the note to anoth

19、er sheet of paper, a file, orother surface without damaging or otherwise modifying thesurface of the sheet or file. The notes display a written messageor reminder.4.2 This specification is based on the U.S. Government CIDA-A-2546, which was cancelled in 1999.5. Apparatus5.1 Roller, Hand-operated:5.1

20、.1 Asteel roller 85 6 2.5 mm (3.25 6 0.1 in.) in diameterand 45 6 1.5 mm (1.75 6 0.005 in.) in width, covered withrubber approximately 6 mm (0.25 in.) in thickness, having aShore scale A durometer hardness of 80 6 5. The surface shallbe a true cylinder void of any convex or concave deviations.The ma

21、ss of the roller shall be 2040 6 45 g (4.5 6 0.1 lb).5.1.2 No part of the apparatus shall increase the mass of theroller during use. The roller shall move either mechanically orby hand at the rate of 10 6 0.5 mm/s (24 6 0.5 in./min).5.2 Cylindrical Mandrel for Flagging Test:5.2.1 The mandrel shall b

22、e a smooth cylinder, 51 mm (2 in.)in diameter and a minimum of 20 cm (8 in.) long. Suitablematerials include wood, plastic, and aluminum. The mandrelmay be a solid cylinder or a hollow tube.6. Test Materials6.1 Multi-purpose Copy PaperHammermill Fore DP,Multi-Function Paper, White #10326-7 or equiva

23、lent.6.2 Double-coated pressure sensitive adhesive tape, withpermanent adhesive on both sides of the tape.7. Conditioning7.1 Condition the pads of repositionable notes in the stan-dard conditioning atmosphere as described in Practice D4332for a period of not less than 24 h.7.2 Conduct tests in an at

24、mosphere of 50 6 2 % relativehumidity and 23.0 6 2.0C.8. Classification8.1 The size of the pads shall be as listed in Table 1. Theadhesive stripe is located on the top of the horizontal dimen-sion of the pad.9. Ordering Information9.1 The inquiry or order shall include the following:9.1.1 ASTM desig

25、nation and date of issue,9.1.2 Type required (see 8.1),9.1.3 Recycled paper content for government purchase (see19.1),9.1.4 When testing and inspection certification is required(see Section 21),9.1.5 Packaging and marking (see 10.1), and9.1.6 Color of paper and graphics, if any (see 11.1).10. Packag

26、ing and Package Marking10.1 Packaging and package marking shall be as specified inthe contract or order.11. Color and Graphics11.1 The color and graphics of the repositionable note padsshall conform to those commercially available.12. Materials and Manufacture12.1 ConstructionA minimum average of 10

27、0 sheets ofpaper shall be assembled in the form of a pad. No individualpad shall contain fewer than 97 sheets. The pad of paper and abacking sheet shall be securely fastened together by means ofthe repositionable, pressure-sensitive adhesive coating.13. Physical Properties13.1 Paper:13.2 The paper u

28、sed in the construction of the pad shall beof the color as specified in the ordering description, and shallconform to the requirements shown in Table 2.13.3 Adhesive Coating:13.4 Each sheet of paper in the pad shall have a coating ofrepositionable, pressure-sensitive adhesive located on the backside

29、 of the sheet. The adhesive coating shall be applied flush toone horizontal edge of the sheet, shall extend the entire widthof the sheet, and shall have a minimum width of 6.4 mm (14in.).TABLE 1 Dimensions of NotepadsTypeHorizontalDimensionVerticalDimensionTolerance1 127 mm (5 in.) 76 mm (3 in.) 1.6

30、 mm (116 in.)2 76mm(3in.) 76mm(3in.) 1.6mm(116 in.)3 51mm(2in.) 38mm(1.5in.) 1.6mm(116 in.)4 51mm(2in.) 76mm(3in.) 1.6mm(116 in.)5 101 mm (4 in.) 152 mm (6 in.) 1.6 mm (116 in.)6 Custom Custom 1.6 mm (116 in.)TABLE 2 Paper SpecificationsProperty Unit RequirementTAPPITestMethodBasis Weight g/m2, 500

31、sheets(lbs/17 22 in.,500 sheets)67, min(18.0, min)T 410Thickness mm (in.) 0.094 0.013(0.0037 0.0005)T411D6787/D6787M 02 (2017)214. Performance Requirements14.1 Writing Quality:14.1.1 The sheets of pad paper shall not exhibit feathering,spreading, skipping, beading, visible discontinuities or fadingo

32、f ink when written on with a metal roller, felt tip, fountainpen, permanent marker, or ball point pen.14.2 Sheet Removal:14.2.1 The sheets of pad paper shall release easily from thepad without leaving any trace of adhesive on the underlyingsheet.14.3 Multiple Sheet Lift:14.3.1 When removed from the

33、pad, the first note removedshall not remove another note when tested according to thefollowing method.14.3.2 A pad is securely mounted to a flat, hard, horizontalsurface with double-coated pressure sensitive adhesive tape.The tape covers the entire back side of the pad and thenon-adhesive side of th

34、e pad faces up. A random number ofsheets between 1 and 60 are removed from the top of the padand discarded. The sheet remaining on top of the pad isremoved by grasping between the thumb and forefinger andlifting off the pad at a 90 angle. The next 24 sheets areremoved from the same pad in a like man

35、ner for a total of 25sheets. Count the number of times more than one sheet isremoved at a time (multiple lift). Repeat the test five times onthe same lot of pads and average the number of multiple liftsto obtain an individual test result. Multiple lift shall not occurmore than one time per pad.14.4

36、Fiber Pull:14.4.1 When adhered to a sheet of copy paper, notes shallnot pull paper fibers from the copy paper when tested by thefollowing method.14.4.2 Place a sheet of multi-purpose copy paper on a hard,flat surface. Randomly select two test sheets from the note pad.Separately place the two test sh

37、eets of the pad paper on thecopy paper and adhere each by rolling once in their lengthwisedirection (that is, once back and once forth) using the hand heldroller. On one of the test sheets, write over the adhesive striparea with a sharp No. 2 pencil, using enough pressure to indentthe paper. Remove

38、each test sheet from the copy paper.Evidence of paper fibers on the adhesive strip shall beconsidered as failure to meet the requirement.14.5 Initial Flagging:14.5.1 The sheets of pad paper, when adhered to a sheet ofmulti-purpose copy paper, shall remain attached to the copypaper when tested as spe

39、cified in the following method.14.5.2 Adhere a sheet of the pad paper to the copy paperusing the method described in 14.4.2. Hold the edges of thespecimen so they do not lift off the paper before the timer isstarted. By hand, roll the combined sample around a cylindricalmandrel 51.0 mm (2.0 in.) in

40、diameter with the horizontal edgeof the sheet perpendicular to the axis of the cylinder. See Fig.1. Flagging is defined as the length of the adhesive end of thesheet that peels away from the copy paper due to stresses frombeing bent around a curve. Total flagging is the sum of flaggingat both ends o

41、f the sheet. Mark the points at which thespecimen separates from the paper after 30 s have elapsed. Testfive specimens from the same lot of notes and average theflagging values to obtain an individual test result.14.5.3 The note pads shall not show a total flagging lengthin excess of 25 % of the len

42、gth of the horizontal edge 30 s afterthe combined sample is mounted on the cylindrical mandrel.See Table 3.14.6 Repositioned Flagging:14.6.1 After repositioning notes to paper 10 times andtesting for flagging, the note shall remain attached to the paperwhen tested according to the following method.1

43、4.6.2 A sheet from a note pad is positioned on a sheet ofmulti-purpose copy paper and adhered using the proceduredescribed in 14.4.2. It is then removed and repositioned on afresh section of the copy paper and adhered as described above.This cycle is repeated 9 times for a total of 10 adhesions. The

44、sheet is then tested for initial flagging per 14.5. Repeat this test5 times per lot of notes and average the results to obtain anindividual test result.14.6.3 Repositioned flagging shall not exceed 60 % of thelength of the horizontal edge. See Table 3.15. Environmental Requirements15.1 BleachingTo o

45、btain an acceptable brightness orcolor, chemical bleaching of the paper may be used. Thebleaching process shall be elemental chlorine free. Certifica-tion of compliance shall be made available upon request.FIG. 1 Flagging TestTABLE 3 Sheet Attachment Initial and Repositioned FlaggingSheet SizeTotal

46、InitialFlaggingmm (in.), maxTotal RepositionedFlaggingmm (in.), max12776mm(53in.) 32mm(1.25in.) 76mm(3.0in.)7676mm(33in.) 19mm(0.75in.) 46mm(1.8in.)5138mm(21.5in.) 13mm(0.50in.) 30mm(1.2in.)5176mm(23in.) 13mm(0.50in.) 30mm(1.2in.)101152mm(46in.) 25mm(1.00in.) 61mm(2.4in.)D6787/D6787M 02 (2017)315.2

47、Environmental RequirementsThe repositionablewriting paper shall not contain toxic or potentially harmfulmaterials as defined in Federal Document 16 CFR Part 1500.3.The contractor shall certify that no heavy metals, defined aslead, mercury, cadmium or hexavalent chromium, are inten-tionally introduce

48、d into the repositionable notes nor are theyintroduced into the packages for this product as specified in theCONEG Model Toxics Legislation.15.3 Food ContactRepositionable notes are not intendedto be used as food additives nor are they intended to be used indirect food contact.16. Workmanship, Finis

49、h, and Appearance16.1 Sheets of pad paper shall be clean and free from dirt,foreign matter, holes, tears, wrinkles, and other defects whichmight affect appearance or serviceability. The sheets shall beuniform with respect to color and formation. Pads shall besquare cut with smooth, clean edges.17. Sampling17.1 End-item ExaminationThe lot size and sampling forend-item examination shall be as called for in Practice D3715/D3715M. The sample unit shall be one pad of notes.17.2 End-item TestingThe lot size and sampling for end-item t