Cellular Wireless Networks.ppt

1、Cellular Wireless Networks,Chapter 10,Cellular Network Organization,Use multiple low-power transmitters (100 W or less) Areas divided into cells Each served by its own antenna Served by base station consisting of transmitter, receiver, and control unit Band of frequencies allocated Cells set up such

2、 that antennas of all neighbors are equidistant (hexagonal pattern),Frequency Reuse,Adjacent cells assigned different frequencies to avoid interference or crosstalk Objective is to reuse frequency in nearby cells 10 to 50 frequencies assigned to each cell Transmission power controlled to limit power

3、 at that frequency escaping to adjacent cells The issue is to determine how many cells must intervene between two cells using the same frequency,Approaches to Cope with Increasing Capacity,Adding new channels Frequency borrowing frequencies are taken from adjacent cells by congested cells Cell split

4、ting cells in areas of high usage can be split into smaller cells Cell sectoring cells are divided into a number of wedge-shaped sectors, each with their own set of channels Microcells antennas move to buildings, hills, and lamp posts,Cellular System Overview,Cellular Systems Terms,Base Station (BS)

5、 includes an antenna, a controller, and a number of receivers Mobile telecommunications switching office (MTSO) connects calls between mobile units Two types of channels available between mobile unit and BS Control channels used to exchange information having to do with setting up and maintaining ca

6、lls Traffic channels carry voice or data connection between users,Steps in an MTSO Controlled Call between Mobile Users,Mobile unit initialization Mobile-originated call Paging Call accepted Ongoing call Handoff,Additional Functions in an MTSO Controlled Call,Call blocking Call termination Call drop

7、 Calls to/from fixed and remote mobile subscriber,Mobile Radio Propagation Effects,Signal strength Must be strong enough between base station and mobile unit to maintain signal quality at the receiver Must not be so strong as to create too much cochannel interference with channels in another cell us

8、ing the same frequency band Fading Signal propagation effects may disrupt the signal and cause errors,Handoff Performance Metrics,Cell blocking probability probability of a new call being blocked Call dropping probability probability that a call is terminated due to a handoff Call completion probabi

9、lity probability that an admitted call is not dropped before it terminates Probability of unsuccessful handoff probability that a handoff is executed while the reception conditions are inadequate,Handoff Performance Metrics,Handoff blocking probability probability that a handoff cannot be successful

10、ly completed Handoff probability probability that a handoff occurs before call termination Rate of handoff number of handoffs per unit time Interruption duration duration of time during a handoff in which a mobile is not connected to either base station Handoff delay distance the mobile moves from t

11、he point at which the handoff should occur to the point at which it does occur,Handoff Strategies Used to Determine Instant of Handoff,Relative signal strength Relative signal strength with threshold Relative signal strength with hysteresis Relative signal strength with hysteresis and threshold Pred

12、iction techniques,Power Control,Design issues making it desirable to include dynamic power control in a cellular system Received power must be sufficiently above the background noise for effective communication Desirable to minimize power in the transmitted signal from the mobile Reduce cochannel in

13、terference, alleviate health concerns, save battery power In SS systems using CDMA, its desirable to equalize the received power level from all mobile units at the BS,Types of Power Control,Open-loop power control Depends solely on mobile unit No feedback from BS Not as accurate as closed-loop, but

14、can react quicker to fluctuations in signal strength Closed-loop power control Adjusts signal strength in reverse channel based on metric of performance BS makes power adjustment decision and communicates to mobile on control channel,Traffic Engineering,Ideally, available channels would equal number

15、 of subscribers active at one time In practice, not feasible to have capacity handle all possible load For N simultaneous user capacity and L subscribers L N blocking system,Blocking System Performance Questions,Probability that call request is blocked? What capacity is needed to achieve a certain u

16、pper bound on probability of blocking? What is the average delay? What capacity is needed to achieve a certain average delay?,Traffic Intensity,Load presented to a system: = mean rate of calls attempted per unit time h = mean holding time per successful call A = average number of calls arriving duri

17、ng average holding period, for normalized ,Factors that Determine the Nature of the Traffic Model,Manner in which blocked calls are handled Lost calls delayed (LCD) blocked calls put in a queue awaiting a free channel Blocked calls rejected and dropped Lost calls cleared (LCC) user waits before anot

18、her attempt Lost calls held (LCH) user repeatedly attempts calling Number of traffic sources Whether number of users is assumed to be finite or infinite,First-Generation Analog,Advanced Mobile Phone Service (AMPS) In North America, two 25-MHz bands allocated to AMPS One for transmission from base to

19、 mobile unit One for transmission from mobile unit to base Each band split in two to encourage competition Frequency reuse exploited,AMPS Operation,Subscriber initiates call by keying in phone number and presses send key MTSO verifies number and authorizes user MTSO issues message to users cell phon

20、e indicating send and receive traffic channels MTSO sends ringing signal to called party Party answers; MTSO establishes circuit and initiates billing information Either party hangs up; MTSO releases circuit, frees channels, completes billing,Differences Between First and Second Generation Systems,D

21、igital traffic channels first-generation systems are almost purely analog; second-generation systems are digital Encryption all second generation systems provide encryption to prevent eavesdropping Error detection and correction second-generation digital traffic allows for detection and correction,

22、giving clear voice reception Channel access second-generation systems allow channels to be dynamically shared by a number of users,Mobile Wireless TDMA Design Considerations,Number of logical channels (number of time slots in TDMA frame): 8 Maximum cell radius (R): 35 km Frequency: region around 900

23、 MHz Maximum vehicle speed (Vm):250 km/hr Maximum coding delay: approx. 20 ms Maximum delay spread (m): 10 s Bandwidth: Not to exceed 200 kHz (25 kHz per channel),Steps in Design of TDMA Timeslot,GSM Network Architecture,Mobile Station,Mobile station communicates across Um interface (air interface)

24、with base station transceiver in same cell as mobile unit Mobile equipment (ME) physical terminal, such as a telephone or PCS ME includes radio transceiver, digital signal processors and subscriber identity module (SIM) GSM subscriber units are generic until SIM is inserted SIMs roam, not necessaril

25、y the subscriber devices,Base Station Subsystem (BSS),BSS consists of base station controller and one or more base transceiver stations (BTS) Each BTS defines a single cell Includes radio antenna, radio transceiver and a link to a base station controller (BSC) BSC reserves radio frequencies, manages

26、 handoff of mobile unit from one cell to another within BSS, and controls paging,Network Subsystem (NS),NS provides link between cellular network and public switched telecommunications networks Controls handoffs between cells in different BSSs Authenticates users and validates accounts Enables world

27、wide roaming of mobile users Central element of NS is the mobile switching center (MSC),Mobile Switching Center (MSC) Databases,Home location register (HLR) database stores information about each subscriber that belongs to it Visitor location register (VLR) database maintains information about subsc

28、ribers currently physically in the region Authentication center database (AuC) used for authentication activities, holds encryption keys Equipment identity register database (EIR) keeps track of the type of equipment that exists at the mobile station,TDMA Format Time Slot Fields,Trail bits allow syn

29、chronization of transmissions from mobile units Encrypted bits encrypted data Stealing bit - indicates whether block contains data or is “stolen“ Training sequence used to adapt parameters of receiver to the current path propagation characteristics Strongest signal selected in case of multipath prop

30、agation Guard bits used to avoid overlapping with other bursts,GSM Speech Signal Processing,GSM Signaling Protocol Architecture,Functions Provided by Protocols,Protocols above the link layer of the GSM signaling protocol architecture provide specific functions: Radio resource management Mobility man

31、agement Connection management Mobile application part (MAP) BTS management,Advantages of CDMA Cellular,Frequency diversity frequency-dependent transmission impairments have less effect on signal Multipath resistance chipping codes used for CDMA exhibit low cross correlation and low autocorrelation P

32、rivacy privacy is inherent since spread spectrum is obtained by use of noise-like signals Graceful degradation system only gradually degrades as more users access the system,Drawbacks of CDMA Cellular,Self-jamming arriving transmissions from multiple users not aligned on chip boundaries unless users

33、 are perfectly synchronized Near-far problem signals closer to the receiver are received with less attenuation than signals farther away Soft handoff requires that the mobile acquires the new cell before it relinquishes the old; this is more complex than hard handoff used in FDMA and TDMA schemes,Mo

34、bile Wireless CDMA Design Considerations,RAKE receiver when multiple versions of a signal arrive more than one chip interval apart, RAKE receiver attempts to recover signals from multiple paths and combine them This method achieves better performance than simply recovering dominant signal and treati

35、ng remaining signals as noise Soft Handoff mobile station temporarily connected to more than one base station simultaneously,Principle of RAKE Receiver,Types of Channels Supported by Forward Link,Pilot (channel 0) - allows the mobile unit to acquire timing information, provides phase reference and p

36、rovides means for signal strength comparison Synchronization (channel 32) - used by mobile station to obtain identification information about cellular system Paging (channels 1 to 7) - contain messages for one or more mobile stations Traffic (channels 8 to 31 and 33 to 63) the forward channel suppor

37、ts 55 traffic channels,Forward Traffic Channel Processing Steps,Speech is encoded at a rate of 8550 bps Additional bits added for error detection Data transmitted in 2-ms blocks with forward error correction provided by a convolutional encoder Data interleaved in blocks to reduce effects of errors D

38、ata bits are scrambled, serving as a privacy mask,Forward Traffic Channel Processing Steps (cont.),Power control information inserted into traffic channel DS-SS function spreads the 19.2 kbps to a rate of 1.2288 Mbps using one row of 64 x 64 Walsh matrix Digital bit stream modulated onto the carrier

39、 using QPSK modulation scheme,ITUs View of Third-Generation Capabilities,Voice quality comparable to the public switched telephone network 144 kbps data rate available to users in high-speed motor vehicles over large areas 384 kbps available to pedestrians standing or moving slowly over small areas

40、Support for 2.048 Mbps for office use Symmetrical / asymmetrical data transmission rates Support for both packet switched and circuit switched data services,ITUs View of Third-Generation Capabilities,An adaptive interface to the Internet to reflect efficiently the common asymmetry between inbound an

41、d outbound traffic More efficient use of the available spectrum in general Support for a wide variety of mobile equipment Flexibility to allow the introduction of new services and technologies,Alternative Interfaces,CDMA Design Considerations,Bandwidth limit channel usage to 5 MHz Chip rate depends

42、on desired data rate, need for error control, and bandwidth limitations; 3 Mcps or more is reasonable Multirate advantage is that the system can flexibly support multiple simultaneous applications from a given user and can efficiently use available capacity by only providing the capacity required for each service,