Chapter 17Applications of Infrared Spectrometry.ppt

1、Chapter 17 Applications of Infrared Spectrometry,Infrared spectrometry is applied to the qualitative and quantitative determination of molecular species of all types. The most widely used region is the mid-infrared that extends from about 670 to 4000 cm-1 (2.5 to 14.9 m). The near-infrared region fr

2、om 4000 to 14,000 cm-1 (0.75 to 2.5 m) also finds considerable use for the routine quantitative determination. The far-infrared region has been for the determination of the structures of inorganic and metal-organic species.,MID-INFRARED ABSORPTION SPECTROMETRYSample HandlingNo good solvents exist th

3、at are transparent throughout the region of interest. As a consequence, sample handling is frequently the most difficult and time-consuming part of an infrared spectrometric analysis.Gases: The spectrum of a low-boiling liquid or gas can be obtained by permitting the sample to expand into an evacuat

4、ed cylindrical cell equipped with suitable windows.,Sample HandlingSolutions: A convenient way of obtaining infrared spectra is on solutions prepared to contain a known concentration of sample. This technique is somewhat limited in its applications, however, by the availability of solvents that are

5、transparent over significant regions in the infrared.Solvents: No single solvents is transparent throughout the entire mid-infrared region. Water and alcohols are seldom employed, not only because they absorb strongly, but also because they attack alkali-metal halides, the most common materials used

6、 for cell windows.,Sample HandlingCells: Sodium chloride windows are most commonly employed; even with care, however, their surfaces eventually become fogged due to absorption of moisture. Polishing with a buffing powder returns them to their original condition.Liquids: When the amount of liquid sam

7、ple is small or when a suitable solvent is unavailable, it is common practice to obtain spectra on the pure (neat) liquid. A drop of the neat liquid is squeezed between two rock-salt plated to give a layer that has a thickness of 0.01 mm or less. The two plates, held together are then mounted in the

8、 beam path. Such a technique does not give reproducible transmittance data, but the resulting spectra are usually satisfactory for qualitative investigations.,Sample Handling Solids: Most organic compounds exhibit numerous absorption peaks throughout the mid-infrared region, and finding a solvent th

9、at does not have overlapping peaks is often impossible. As a consequence, spectra are often obtained on dispersions of the solid in a liquid or solid matrix.Pelleting: One of the most popular techniques for handling solid samples has been KBr pelleting. A milligram or less of the finely ground sampl

10、e is intimately mixed with about 100 mg of dried potassium bromide powder. The mixture is then pressed in a die at 10,000 to 15,000 pounds per square inch to yield a transparent disk. The disk is then held in the instrument beam for spectroscopic examination.,Sample Handling Mulls: Infrared spectra

11、of solids that are not soluble in an infrared-transparent solvent or are not conveniently pelleted in KBr are often obtained by dispersing the analyte in a mineral oil or fluorinated hydrocarbon mull. Mulls are formed by grinding 2 to 5 mg of the finely powdered sample in the presence of one or two

12、drops of a heavy hydrocarbon oil (Nujol). If hydrocarbon bands interfere, Fluorolube, a halogenated polymer, can be used. The resulting mull is then examined as a film between flat salt plates.,Qualitative AnalysisThe appearance of I.R. instrument revolutionized the way chemists went about identifyi

13、ng organic, inorganic, and biological species. The time required to perform a structural determination was reduced by a factor of ten, one hundred, or even one thousand. Identification of an organic compound is a two-step process. The first step involves determining what functional groups are most l

14、ikely present by examining the group frequency region.,Qualitative AnalysisThe second step then involves a detailed comparison of the spectrum of the unknown with the spectra of pure compounds that contain all of the functional groups found in the first step. The fingerprint region, from 1200 to 600

15、 cm -1 is particularly useful because small differences in the structure and constitution of a molecule result in significant changes in the appearance and distribution of absorption peaks in this region.,Qualitative AnalysisGroup Frequencies: The approximate frequency (or wavenumber) at which an or

16、ganic functional group, such as C=O, C=C, CH, CC, or OH absorbs infrared radiation can be calculated from the masses of the atoms and the force constant of the bond between them. These frequencies, called group frequencies, are seldom totally invariant because of interactions with other vibrations a

17、ssociated with one or both of the atoms composing the group. A range of frequencies can be assigned within which it is highly probable that the absorption peak for a given functional group will be found.,Qualitative AnalysisThe “Fingerprint” Region: Small differences in the structure and constitutio

18、n of a molecule result in significant changes in the distribution of absorption peaks in this region of the spectrum that extends from about 1200 to 700 cm-1. As a consequence, a close match between two spectra in this fingerprint region constitutes strong evidence for the identity of compounds yiel

19、ding the spectra. Exact interpretation of spectra in this region is seldom possible because of the complexity of the spectra.,Qualitative AnalysisComputer Search Systems: Virtually all infrared instrument manufactures now offer computer search systems to assist chemist in identifying compounds from

20、stored infrared spectral data. The position and relative magnitudes of peaks in the spectrum of the analyte are determined and stored in memory to give a peak profile, which can then be compared with profiles of pure compounds stored. The computer then matches profiles and prints a list of compounds

21、 having spectra similar to that of the analyte. Usually the spectrum of the analyte and that of each potential match can then be shown simultaneously on the computer display for comparison.,Quantitative ApplicationsQuantitative infrared absorption methods differ somewhat from ultraviolet/visible mol

22、ecular spectroscopic methods because of the greater complexity of the spectra, the narrowness of the absorption bands, and the instrumental limitations of infrared instruments. Quantitative data obtained with infrared instruments are generally significantly inferior in quality to data obtained with

23、ultraviolet/visible spectrophotometers.,MID-INFRARED REFLECTION SPECTROMETYInfrared reflection spectrometry has found a number of applications, particularly for dealing with solid samples that are difficult to handle, such as polymer films and fibers, foods, rubbers, agriculture products, and many o

24、thers. Mid-infrared reflection spectra are similar in general appearance and provide the same information as do their absorption counterparts. Reflectance spectra can be used for both qualitative and quantitative analysis.,NEAR-INFRARED SPECTROSCOPYThe near-infrared (NIR) region of the spectrum exte

25、nds from the upper wavelength end of the visible region at about 770 nm to 2500 nm (13,000 to 4000 cm-1). Absorption bands in this region are overtones or combinations of fundamental stretching vibrational bands that occur in the region of 3000 to 1700 cm-1 . The bonds involved are usually CH, NH, a

26、nd OH. Because the bands are overtones or combination, their molar absorptivities are low.,FAR-INFRARED SPECTROSCOPYThe far-infrared region is particularly useful for inorganic studies because absorption due to stretching and bending vibrations of bonds between metal atoms and both inorganic and org

27、anic ligands generally occur at frequencies lower than 650 cm-1 (15m). For example, heavy-metal iodides generally absorb in the region below 100 cm-1. Far-infrared studies of inorganic solids have also provided useful information about lattice energies of crystals and transition energies of semiconducting materials.,Empirical Formula C3H6O,Empirical Formula C9H10O,MW 56,Nitrogen containing compound,