BS ISO 6022-2006 en_4491 Hydraulic fluid power - Mounting dimensions for single rod cylinders 25M Pa (250 bar) series《液压传动.25M Pa (250巴)系列单杆汽缸安装尺寸》.pdf

1、BRITISH STANDARD BS ISO 6022:2006 Hydraulic fluid power Mounting dimensions for single rod cylinders, 25 MPa (250 bar) series ICS 23.100.20 BS ISO 6022:2006 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 15 February 2006 BSI 15 February 2006

2、 ISBN 0 580 47586 7 National foreword This British Standard reproduces verbatim ISO 6022:2006 and implements it as the UK national standard. It supersedes BS ISO 6022:1981 which is withdrawn. The UK participation in its preparation was entrusted by Technical Committee MCE/18, Fluid power systems and

3、 components, to Subcommittee MCE/18/-/3, Cylinders, which has the responsibility to: A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement international publications referred to in this document ma

4、y be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users

5、are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, a

6、nd keep UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the ISO title page, pages ii to iv, pages 1 to 13 and a back cover. The BSI copyright notice displayed

7、in this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date Comments Reference number ISO 6022:2006(E)INTERNATIONAL STANDARD ISO 6022 Second edition 2006-02-01 Hydraulic fluid power Mounting dimensions for single rod cylinders, 25 MPa (250 bar) ser

8、ies Transmissions hydrauliques Dimensions dinterchangeabilit des vrins 25 MPa (250 bar) simple tige BS ISO 6022:2006ii iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International

9、 Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, a

10、lso take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical commit

11、tees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the pos

12、sibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 6022 was prepared by Technical Committee ISO/TC 131, Fluid power systems, Subcommittee SC 3, Cylinders. This second edition ca

13、ncels and replaces the first edition (ISO 6022:1981 and ISO 8137:1986), which have been technically revised. BS ISO 6022:2006iv Introduction In hydraulic fluid power systems, power is transmitted and controlled through a liquid under pressure within an enclosed circuit. One component of such systems

14、 is the fluid power cylinder. This is a device that converts power into linear mechanical force and motion. It consists of a movable element, i.e. a piston and piston rod, operating within a cylindrical bore. BS ISO 6022:20061 Hydraulic fluid power Mounting dimensions for single rod cylinders, 25 MP

15、a (250 bar) series 1 Scope This International Standard establishes mounting dimensions for hydraulic cylinders for use at 25 MPa 250 bar 1) , as required for interchangeability of these cylinders. NOTE This International Standard allows manufacturers of hydraulic equipment flexibility in the design

16、of 25 MPa (250 bar) cylinders and does not restrict technical development; however, it does provide basic guidelines. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated re

17、ferences, the latest edition of the referenced document (including any amendments) applies. ISO 1179-1 2) , Connections for general use and fluid power Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing Part 1: Threaded ports ISO 3320, Fluid power systems and compo

18、nents Cylinder bores and piston rod diameters Metric series ISO 4395, Fluid power systems and components Cylinders Piston rod thread dimensions and types ISO 5598 3) , Fluid power systems and components Vocabulary ISO 6099, Fluid power systems and components Cylinders Identification code for mountin

19、g dimensions and mounting types ISO 6149-1 4) , Connections for fluid power and general use Ports and stud ends with ISO 261 threads and O-ring sealing Part 1: Ports with O-ring seal in truncated housing ISO 6162-1, Hydraulic fluid power Flange connectors with split or one-piece flange clamps and me

20、tric or inch screws Part 1: Flange connectors for use at pressures of 3,5 MPa (35 bar) to 35 MPa (350 bar), DN 13 to DN 127 ISO 6162-2, Hydraulic fluid power Flange connectors with split or one-piece flange clamps and metric or inch screws Part 2: Flange connectors for use at pressures of 35 MPa (35

21、0 bar) to 40 MPa (400 bar), DN 13 to DN 51 1) 1 bar = 0,1 MPa = 10 5Pa; 1MPa = 1 N/mm 22) To be published. (Revision of ISO 1179:1981) 3) To be published. (Revision of ISO 5598:1985) 4) To be published. (Revision of ISO 6149-1:1993) BS ISO 6022:20062 ISO 6164, Hydraulic fluid power Four-screw, one-p

22、iece square-flange connections for use at pressures of 25 MPa and 40 MPa (250 bar and 400 bar) ISO 8132 5) , Hydraulic fluid power Single rod cylinders, 16 MPa (160 bar) medium and 25 MPa (250 bar) series Mounting dimensions for accessories 3 Terms and definitions For the purposes of this document,

23、the terms and definitions given in ISO 5598 apply. 4 Dimensions 4.1 Select mounting dimensions for cylinders manufactured in accordance with this International Standard from Figures 1 to 4 and Tables 1 to 4 inclusive. 4.2 Select dimensions for ports and flanges from Table 5 and the relevant Internat

24、ional Standards cited therein. 4.3 All dimensions and mounting types in this International Standard are labelled with codes in accordance with ISO 6099. 5 Bore sizes This International Standard covers the following bore sizes, in millimetres, in accordance with ISO 3320: 50 63 80 100 125 140 160 180

25、 200 250 320 6 Mounting types This International Standard includes the following mounting types: MF3: Head, circular flange (see Figure 2 and Table 2) MF4: Cap, circular flange (see Figure 2 and Table 2) MP3: Cap, fixed plain eye (see Figure 3 and Table 3) MP4: Cap, detachable plain eye (see Figure

26、3 and Table 3) MP5: Cap, fixed eye with spherical bearing (see Figure 3 and Table 3) MP6: Cap, detachable eye with spherical bearing (see Figure 3 and Table 3) MT4: Intermediate fixed or movable trunnion (male) (see Figure 4 and Table 4). 5) To be published. (Revision of ISO 8132:1986, ISO 6981:1992

27、 and ISO 6982:1992) BS ISO 6022:20063 7 Piston rod characteristics 7.1 This International Standard covers piston rods having a shouldered male thread end (see Figure 1 and Table 1 for basic dimensions). 7.2 For rod end types, see ISO 4395. 7.3 Accessory mounting dimensions shall be selected in accor

28、dance with ISO 8132. 8 Identification statement (reference to this International Standard) Use the following statement in test reports, catalogues and sales literature when electing to comply with this International Standard: “Hydraulic single rod cylinders for use at 25 MPa (250 bar) selected in ac

29、cordance with ISO 6022:2006, Hydraulic fluid power Mounting dimensions for single rod cylinders, 25 MPa (250 bar) series.” BS ISO 6022:20064 For rod end types, see ISO 4395. Figure 1 General dimensions BS ISO 6022:20065Table 1 General dimensions Dimensions in millimetres Bore MMaZJbKKaA VE WFb6g max

30、. max. 32 50 36 240 M27 2 36 29 47 40 63 45 270 M33 2 45 32 53 50 80 56 300 M42 2 56 36 60 63 100 70 335 M48 2 63 41 68 80 125 90 390 M64 3 85 45 76 90 140 100 425 M72 3 90 48 76 100 160 110 460 M80 3 95 50 85 110 180 125 497 M90 3 106 55 95 125 200 140 540 M100 3 112 61 101 160 250 180 640 M125 4 1

31、25 71 113 200 320 220 750 M160 4 160 88 136 aIf other piston rod diameters or other threads are required, use those identified in ISO 3320 and ISO 4395. bTolerances for dimensions ZJ and WF are dependent on stroke; see Table 6. BS ISO 6022:20066 a) Head mounting b) Cap mounting a Optional. Figure 2

32、MF3 Head, circular flange and MF 4 Cap, circular flange BS ISO 6022:20067 Table 2 Dimensions of circular flange mountings MF3 and MF4 Dimensions in millimetres Bore FB FC VD WCaZPaZB B, BA UC NF H13 js13 min. max. H8 / f8 max. js13 50 8 13,5 132 4 22 265 244 63 160 25 63 8 13,5 150 4 25 298 274 75 1

33、80 28 80 8 17,5 180 4 28 332 305 90 215 32 100 8 22 212 5 32 371 340 110 260 36 125 8 22 250 5 36 430 396 132 300 40 140 8 26 285 5 36 465 430 145 340 40 160 8 26 315 5 40 505 467 160 370 45 180 8 33 355 5 45 550 505 185 425 50 200 8 33 385 5 45 596 550 200 455 56 250 8 39 475 8 50 703 652 250 545 6

34、3 320 8 45 600 8 56 830 764 320 680 80 aTolerances for dimensions WC and ZP are dependent on stroke; see Table 6. BS ISO 6022:20068 Figure 3 MP3 Cap, fixed plain eye, MP4 Cap, detachable plain eye, MP5 Cap, fixed eye with spherical bearing and MP6 Cap, detachable eye with spherical bearing BS ISO 60

35、22:20069Table 3 Dimensions of cap eye mountings MP3, MP4, MP5 and MP6 Dimensions in millimetres Bore CDaCXbEW aor EXbLaor LTbMRaor MSbXC, XD, XO or XNc,dTilting angle Z H9 H7 h12 min. max. min. 50 32 32 32 40 40 305 4 63 40 40 40 50 50 348 4 80 50 50 50 63 63 395 4 100 63 63 63 71 71 442 4 125 80 80

36、 80 90 90 520 4 140 90 90 90 113 113 580 4 160 100 100 100 112 112 617 4 180 110 110 110 135 135 690 4 200 125 125 125 160 160 756 4 250 160 160 160 200 200 903 4 320 200 200 200 250 250 1080 4 aThe dimensions CD, EW, L and MR are valid for mounting types MP3 and MP4. bThe dimensions CX, EX, LT and

37、MS are valid for mounting types MP5 and MP6. cTolerances for dimensions XC, XD, XO or XN are dependent on stroke; see Table 6. dThe dimension XC is valid for mounting type MP3, the dimension XD is valid for mounting type MP4, the dimension XO is valid for mounting type MP5 and the dimension XN is va

38、lid for mounting type MP6. BS ISO 6022:200610 Figure 4 MT4 Intermediate fixed or movable trunnion (male) Table 4 Dimensions of intermediate male trunnion mounting MT4 Dimensions in millimetres Bore TD TL TM XVaZB f8 js13 h12 max. 50 32 25 112 244 63 40 32 125 274 80 50 40 150 305 100 63 50 180 340 1

39、25 80 63 224 396 140 90 70 265 430 160 100 80 280 467 180 110 90 320 502 200 125 100 335 550 250 160 125 425 652 320 200 160 530 Variable. Users should consult the manufacturer for minimum and maximum values 764 aTolerances for dimensions XV are dependent on stroke; see Table 6. BS ISO 6022:200611 T

40、able 5 Port and flange sizes Dimensions in millimetres ISO 1179-1 port ISO 6149-1 port ISO 6164 Square flange ISO 6162-1 Rectangular flange G M F MM EE EC EE EC Nominal flange size DN FF EA ED Nominal flange size DN FF EA EB ED Bore 6g min. 6g min. 0 1,5 0,256g 0 1,5 0,2 5 0,25 6g 50 G 1/2 14 M22 1,

41、5 14 63 80 G 3/4 18 M27 2 18 13 15 29,7 M8 13 12,7 17,5 38,1 M8 100 125 G 1 23 M33 2 23 19 20 35,4 M8 19 19,1 22,3 47,6 M10 140 160 180 200 G 1 30 M42 2 30 25 25 43,8 M10 25 25,4 26,2 52,4 M10 250 320 G 1 32 M60 2 32 32 32 51,6 M12 32 31,8 30,2 58,7 M10 CAUTION When selecting the largest diameter pi

42、ston rod in a given bore size in connection with hydraulic systems where pull loads and/or pressure intensification effects may be generated, the pressure in the piston rod cavity of the cylinder can be two or more times the working pressure of the hydraulic system. In these cases, flange ports in a

43、ccordance with ISO 6162-1 or ISO 6164, as shown in this table, may not have sufficient pressure ratings. When flange ports with a higher pressure rating are needed, they can be selected from the higher pressure series in ISO 6162-2 and ISO 6164. BS ISO 6022:200612 Table 6 Tolerances for mounting dim

44、ensions that are dependent on stroke Dimensions in millimetres Code for mounting dimension ZJaWF WC ZPaXC, XD, XO or XNaXV Nominal stroke Tolerances u 1 250 1,5 2 2 1,5 1,5 2 1 250 u 3 150 3 4 4 3 3 4 3 150 u 8 000 5 8 8 5 5 8 aLength including stroke. Stroke tolerances from Table 7 shall not be add

45、ed to the tolerances in this table. Table 7 Tolerances on piston stroke Dimensions in millimetres Nominal stroke Tolerance u 1 250 2 0 + 1 250 u 3 150 5 0 + 3 150 u 8 000 8 0 +BS ISO 6022:200613 Bibliography 1 ISO 273, Fasteners Clearance holes for bolts and screws 2 ISO 286-2, ISO system of limits

46、and fits Part 2: Tables of standard tolerance grades and limit deviations for holes and shafts 3 ISO 4393, Fluid power systems and components Cylinders Basic series of piston strokes BS ISO 6022:2006BS ISO 6022:2006 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is th

47、e independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure t

48、hat they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers