1、BSI Standards Publication BS ISO 6262-2:2013 End mills with indexable inserts Part 2: End mills with Morse taper shankBS ISO 6262-2:2013 BRITISH STANDARD National foreword This British Standard is the UK implementation of ISO 6262-2:2013. It supersedes BS4193-10:1982 which is withdrawn. The UK parti
2、cipation in its preparation was entrusted to Technical Committee MTE/18, Tools tips and inserts for cutting applications. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a
3、contract. Users are responsible for its correct application. The British Standards Institution 2013. Published by BSI Standards Limited 2013 ISBN 978 0 580 81022 0 ICS 25.100.20 Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published unde
4、r the authority of the Standards Policy and Strategy Committee on 30 September 2013. Amendments/corrigenda issued since publication Date T e x t a f f e c t e dBS ISO 6262-2:2013 ISO 2013 End mills with indexable inserts Part 2: End mills with Morse taper shank Fraises en bout plaquettes amovibles P
5、artie 2: Fraises queue cne Morse INTERNATIONAL STANDARD ISO 6262-2 Second edition 2013-09-01 Reference number ISO 6262-2:2013(E)BS ISO 6262-2:2013ISO 6262-2:2013(E)ii ISO 2013 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO 2013 All rights reserved. Unless otherwise specified, no part of this p
6、ublication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the c
7、ountry of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in SwitzerlandBS ISO 6262-2:2013ISO 6262-2:2013(E) ISO 2013 All rights reserved iii Contents Page Foreword iv 1 Scope . 1 2 N
8、ormative references 1 3 Dimensions . 1 Annex A (informative) Relationship between designations in this part of ISO 6262 and the ISO 13399 series . 3 Bibliography 4BS ISO 6262-2:2013ISO 6262-2:2013(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of natio
9、nal standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. Internati
10、onal organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The procedures used to develop this document and those intende
11、d for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2. www.iso.or
12、g/directives Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be i
13、n the Introduction and/or on the ISO list of patent declarations received. www.iso.org/patents Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement. The committee responsible for this document is ISO/TC 29, Small tools, Subcomm
14、ittee SC 9, Tools with cutting edges made of hard cutting materials. This second edition cancels and replaces the first edition (ISO 6262-2:1982), of which it constitutes a minor revision. ISO 6262 consists of the following parts, under the general title End mills with indexable inserts: Part 1: End
15、 mills with flatted cylindrical shank Part 2: End mills with Morse taper shankiv ISO 2013 All rights reservedBS ISO 6262-2:2013INTERNATIONAL ST ANDARD ISO 6262-2:2013(E) End mills with indexable inserts Part 2: End mills with Morse taper shank 1 Scope This part of ISO 6262 specifies the dimensions o
16、f end mills with indexable inserts and Morse taper shank according to ISO 296. The form and dimensions of the inserts are left to the discretion of the manufacturer. 2 Normative references TThe following documents, in whole or in part, are normatively referenced in this document and are indispensabl
17、e to its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 296, Machine tools Self-holding tapers for tool shanks 3 Dimensions Key 1 Morse taper shank a The value of 90 shal
18、l be the nominal value of the cutting edge angle of the insert. The effective angle obtained on the workpiece depends on the geometry and the diameter of the milling cutter together with the cutting depth. Figure 1 Dimensions ISO 2013 All rights reserved 1BS ISO 6262-2:2013ISO 6262-2:2013(E) Table 1
19、 Dimensions Dimensions in millimetres d j s 14 Morse taper No. a l 1max. l 16 2 25 94 20 3 30 116 25 3 38 124 32 3 38 124 40 4 48 157 50 4 48 157 aThe shank dimensions shall be in accordance with ISO 296.2 ISO 2013 All rights reservedBS ISO 6262-2:2013ISO 6262-2:2013(E) Annex A (informative) Relatio
20、nship between designations in this part of ISO 6262 and the ISO 13399 series For the relationship between designations in this part of ISO 6262 and preferred symbols according to ISO 13399 (all parts), see Table A.1. Table A.1 Relationship between designations in this part of ISO 6262 and the ISO 13
21、399 series Symbol in ISO 6262-2 (this part of ISO 6262) Reference in ISO 6262-2 (this part of ISO 6262) Property name in the ISO 13399 series Symbol in the ISO 13399 series Reference in the ISO 13399 series d Figure 1 and Table 1 Cutting diameter DC ISO/TS 13399-3, 71D084653E57F l Figure 1 and Table
22、 1 Overall length OAL ISO/TS 13399-3, 71D078EB7C086 l 1 Figure 1 and Table 1 Head length LH ISO/TS 13399-3, 71D07574A61E8 90 Figure 1 Tool cutting edge angle KAPR ISO/TS 13399-3, 71D078F683C9B ISO 2013 All rights reserved 3BS ISO 6262-2:2013ISO 6262-2:2013(E) Bibliography 1 ISO 13399 (all parts), Cu
23、tting tool data representation and exchange4 ISO 2013 All rights reservedBS ISO 6262-2:2013BS ISO 6262-2:2013ISO 6262-2:2013(E) ISO 2013 All rights reserved IC S 25.100.20 Price based on 4 pagesThis page deliberately left blankBSI is the national body responsible for preparing British Standards and
24、other standards-related publications, information and services. BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited. British Standards Institution (BSI) BSI Group Headquarters 389 Chiswick High Road London W4 4AL UK About
25、us We bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions. The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultatio
26、n process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals. Information on standards We can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our
27、Customer Services team or Knowledge Centre. Buying standards You can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards
28、 from other Standards Development Organizations, hard copies can be ordered from our Customer Services team. Subscriptions Our range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to With British Standards Online
29、 (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase pr
30、ice of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becomin
31、g a BSI Subscribing Member and the benefits of membership, please visit With a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure y
32、our documentation is current. For further information, email . Revisions Our British Standards and other publications are updated by amendment or revision. We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a Britis
33、h Standard or other BSI publication please inform the Knowledge Centre. Copyright All the data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that owns copyright in the information used (suc
34、h as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any m
35、eans electronic, photocopying, recording or otherwise without prior written permission from BSI. Details and advice can be obtained from the Copyright & Licensing Department. Useful Contacts: Customer Services Tel: +44 845 086 9001 Email (orders): Email (enquiries): Subscriptions Tel: +44 845 086 9001 Email: Knowledge Centre Tel: +44 20 8996 7004 Email: Copyright & Licensing Tel: +44 20 8996 7070 Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW
copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1