BS ISO 6361-4-2014 en_9060 Wrought aluminium and aluminium alloys Sheets strips and plates Sheets and plates Tolerances on shape and dimensions《锻造铝和铝合金 厚板材 薄板材和带材 厚板材和带材 形状和尺寸公差》.pdf

1、BSI Standards Publication BS ISO 6361-4:2014 Wrought aluminium and aluminium alloys Sheets, strips and plates Part 4: Sheets and plates: Tolerances on shape and dimensionsBS ISO 6361-4:2014 BRITISH STANDARD National foreword This British Standard is the UK implementation of ISO 6361-4:2014. The UK p

2、articipation in its preparation was entrusted to Technical Committee NFE/35, Light metals and their alloys. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. User

3、s are responsible for its correct application. The British Standards Institution 2014. Published by BSI Standards Limited 2014 ISBN 978 0 580 84687 8 ICS 77.150.10 Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the authorit

4、y of the Standards Policy and Strategy Committee on 30 September 2014. Amendments/corrigenda issued since publication Date T e x t a f f e c t e d ISO 2014 Wrought aluminium and aluminium alloys Sheets, strips and plates Part 4: Sheets and plates: Tolerances on shape and dimensions Aluminium et alli

5、ages daluminium corroys Tles, bandes et tles paisses Partie 4: Tles et tles paisses: Tolrances sur forme et dimensions INTERNATIONAL STANDARD ISO 6361-4 Third edition 2014-09-15 Reference number ISO 6361-4:2014(E)BS ISO 6361-4:2014ISO 6361-4:2014(E)ii ISO 2014 All rights reserved COPYRIGHT PROTECTED

6、 DOCUMENT ISO 2014 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permissi

7、on can be requested from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in SwitzerlandBS ISO 6361-4:2014ISO 6361

8、-4:2014(E) ISO 2014 All rights reserved iii Contents Page Foreword iv 1 Scope . 1 2 Normative references 1 3 Dimensional tolerances 1 3.1 Thickness . 1 3.2 Width . 5 3.3 Length . 6 4 Shape tolerances . 7 4.1 Lateral curvature . 7 4.2 Flatness tolerances 7 4.3 Squareness tolerances .10 Bibliography .

9、12BS ISO 6361-4:2014ISO 6361-4:2014(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member bod

10、y interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrote

11、chnical Commission (IEC) on all matters of electrotechnical standardization. The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of IS

12、O documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held re

13、sponsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any trade name used in this document is information gi

14、ven for the convenience of users and does not constitute an endorsement. For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the follow

15、ing URL: Foreword - Supplementary information The committee responsible for this document is ISO/TC 79, Light metals and their alloys, Subcommittee SC 6, Wrought aluminium and aluminium alloys. This third edition cancels and replaces the second edition (ISO 6361-4:2011), which has been technically r

16、evised. ISO 6361 consists of the following parts, under the general title Wrought aluminium and aluminium alloys Sheets, strips and plates: Part 1: Technical conditions for inspection and delivery Part 2: Mechanical properties Part 3: Strips: Tolerances on shape and dimensions Part 4: Sheets and pla

17、tes: Tolerances on shape and dimensions Part 5: Chemical compositioniv ISO 2014 All rights reservedBS ISO 6361-4:2014INTERNATIONAL ST ANDARD ISO 6361-4:2014(E) Wrought aluminium and aluminium alloys Sheets, strips and plates Part 4: Sheets and plates: Tolerances on shape and dimensions 1 Scope This

18、part of ISO 6361 specifies the tolerances on shape and dimensions for wrought aluminium and aluminium alloy sheet and plate by hot-rolling or cold-rolling for general engineering applications. It applies to products with a thickness over 0,15 mm up to and including 203 mm. It does not apply to semi-

19、finished rolled products in coiled form to be subjected to further rolling (reroll stock) or to special products, such as those that are corrugated or embossed. Technical conditions for inspection and delivery of products covered by this part of ISO 6361 are specified in ISO 6361-1. 2 Normative refe

20、rences No normative references cited in this document. 3 Dimensional tolerances 3.1 Thickness Thickness tolerances for a cold-rolled product are specified in Table 1 and Table 2. Thickness tolerances for a hot-rolled product are specified in Table 3 and Table 4. When the tolerance is specified as ei

21、ther all plus or minus side, the value in Table 1, Table 2, Table 3, or Table 4 shall be doubled. Tolerances for the products exceeding the range of specified thickness and width shall be agreed upon between the purchaser and the supplier. Table 1 Thickness tolerances for cold-rolled product Dimensi

22、ons in millimetres Specified thickness Alloy number 1050, 1050A, 1070, 1070A,1080, 1080A, 1085, 1100, 1100A, 1200, 1230A, 3003, 3103, 3203, 3005, 3105, 4006, 4007, 4015, 5005, 5010, 5110A, 5050, 8011A, 8021, 8079 Specified width Over Up to and including Up to and including 450 Over 450, up to and in

23、cluding 900 Over 900, up to and including 1 400 Over 1 400, up to and including 1 800 Over 1 800, up to and including 2 300 Over 2 300, up to and includ- ing 2 600 Tolerance 0,15 0,20 0,03 0,03 0,05 ISO 2014 All rights reserved 1BS ISO 6361-4:2014ISO 6361-4:2014(E) Specified thickness Alloy number 1

24、050, 1050A, 1070, 1070A,1080, 1080A, 1085, 1100, 1100A, 1200, 1230A, 3003, 3103, 3203, 3005, 3105, 4006, 4007, 4015, 5005, 5010, 5110A, 5050, 8011A, 8021, 8079 Specified width Over Up to and including Up to and including 450 Over 450, up to and including 900 Over 900, up to and including 1 400 Over

25、1 400, up to and including 1 800 Over 1 800, up to and including 2 300 Over 2 300, up to and includ- ing 2 600 Tolerance 0,20 0,25 0,03 0,04 0,05 0,25 0,45 0,04 0,04 0,05 0,06 0,45 0,70 0,04 0,05 0,06 0,08 0,70 0,90 0,05 0,05 0,06 0,09 0,13 0,90 1,1 0,05 0,06 0,08 0,10 0,13 1,1 1,7 0,06 0,08 0,10 0,

26、13 0,15 1,7 1,9 0,06 0,08 0,10 0,15 0,20 1,9 2,4 0,08 0,08 0,10 0,15 0,20 2,4 2,7 0,09 0,10 0,13 0,18 0,23 2,7 3,6 0,11 0,11 0,13 0,18 0,23 0,25 3,6 4,5 0,15 0,15 0,20 0,23 0,28 0,30 4,5 5,0 0,18 0,18 0,23 0,28 0,33 0,38 5,0 6,5 0,23 0,23 0,28 0,33 0,38 0,43 6,5 8,0 0,33 0,33 0,33 0,38 0,43 0,51 8,0

27、 11 0,48 0,48 0,48 0,48 0,58 0,66 11 16 0,64 0,64 0,64 0,64 0,76 0,89 Table 2 Thickness tolerances for cold-rolled product Dimensions in millimetres Specified thickness Alloy number 2014, 2014A, 2017, 2017A, 2618A, 2219, 2024, 2124, 3004, 3104, 5021, 5026, 5040, 5042, 5049, 5449, 5251, 5052, 5154, 5

28、154A, 5254, 5454, 5754, 5456, 5059, 5070, 5082, 5182, 5083, 5383, 5086, 6016, 6025, 6061, 6082, 7204, 7010, 7020, 7021, 7022, 7050, 7075, 7475, 7178 Specified width Over Up to and includ- ing Up to and includ- ing 450 Over 450, up to and includ- ing 900 Over 900, up to and includ- ing 1 200 Over 1 2

29、00, up to and includ- ing 1 400 Over 1 400, up to and includ- ing 1 500 Over 1 500, up to and includ- ing 1 700 Over 1 700, up to and includ- ing 1 800 Over 1 800, up to and includ- ing 2 000 Over 2 000, up to and includ- ing 2 100 Over 2 100, up to and includ- ing 2 300 Over 2 300, up to and includ

30、- ing 2 400 Over 2 400, up to and includ- ing 2 600 Tolerance 0,20 0,25 0,03 0,04 0,06 0,06 0,25 0,45 0,04 0,04 0,06 0,09 0,45 0,70 0,04 0,05 0,06 0,09 0,10 0,10 0,10 0,70 0,90 0,05 0,05 0,06 0,10 0,13 0,13 0,13 0,15 0,90 1,1 0,05 0,06 0,08 0,10 0,13 0,13 0,13 0,15 1,1 1,7 0,06 0,08 0,10 0,13 0,15 0

31、,15 0,15 0,18 1,7 1,9 0,08 0,08 0,10 0,13 0,15 0,15 0,15 0,18 1,9 2,4 0,09 0,09 0,10 0,13 0,15 0,15 0,15 0,18 0,18 0,30 Table 1 (continued) 2 ISO 2014 All rights reservedBS ISO 6361-4:2014ISO 6361-4:2014(E) Specified thickness Alloy number 2014, 2014A, 2017, 2017A, 2618A, 2219, 2024, 2124, 3004, 310

32、4, 5021, 5026, 5040, 5042, 5049, 5449, 5251, 5052, 5154, 5154A, 5254, 5454, 5754, 5456, 5059, 5070, 5082, 5182, 5083, 5383, 5086, 6016, 6025, 6061, 6082, 7204, 7010, 7020, 7021, 7022, 7050, 7075, 7475, 7178 Specified width Over Up to and includ- ing Up to and includ- ing 450 Over 450, up to and incl

33、ud- ing 900 Over 900, up to and includ- ing 1 200 Over 1 200, up to and includ- ing 1 400 Over 1 400, up to and includ- ing 1 500 Over 1 500, up to and includ- ing 1 700 Over 1 700, up to and includ- ing 1 800 Over 1 800, up to and includ- ing 2 000 Over 2 000, up to and includ- ing 2 100 Over 2 100

34、, up to and includ- ing 2 300 Over 2 300, up to and includ- ing 2 400 Over 2 400, up to and includ- ing 2 600 Tolerance 2,4 2,7 0,10 0,10 0,13 0,13 0,18 0,18 0,18 0,20 0,20 0,41 2,7 3,2 0,11 0,11 0,13 0,13 0,18 0,18 0,18 0,20 0,20 0,41 0,46 0,51 3,2 3,6 0,11 0,11 0,13 0,13 0,18 0,25 0,30 0,33 0,36 0

35、,41 0,46 0,51 3,6 4,5 0,15 0,15 0,20 0,20 0,23 0,30 0,36 0,38 0,41 0,43 0,48 0,58 4,5 5,0 0,18 0,18 0,25 0,25 0,28 0,36 0,41 0,43 0,43 0,43 0,56 0,66 5,0 6,5 0,23 0,23 0,28 0,28 0,33 0,41 0,46 0,46 0,46 0,46 0,61 0,71 6,5 8,0 0,33 0,33 0,33 0,33 0,38 0,46 0,51 0,51 0,51 0,51 0,64 0,76 8,0 11 0,48 0,

36、48 0,48 0,48 0,51 0,51 0,58 0,58 0,64 0,64 0,66 0,84 11 16 0,64 0,64 0,64 0,64 0,64 0,64 0,64 0,76 0,76 0,76 0,89 0,89 Table 3 Thickness tolerances for hot-rolled product Dimensions in millimetres Specified thickness Alloy number 1050, 1050A, 1070, 1070A, 1080, 1080A, 1085,1100, 1100A, 1200, 1230A,

37、3003, 3103, 3203, 3005, 3105, 4006, 4007, 4015, 5005, 5010, 5110A, 5050, 8011A Specified width Over Up to and including Up to and including 900 Over 900, up to and including 1 400 Over 1 400, up to and including 1 800 Over 1 800, up to and including 2 300 Over 2 300, up to and including 2 600 Over 2

38、 600, up to and including 3 400 Tolerance 4 5 0,25 0,30 0,35 0,40 5 6 0,30 0,40 0,45 0,50 6 8 0,45 0,45 0,55 0,65 0,75 0,85 8 11 0,55 0,55 0,65 0,75 0,85 0,95 11 16 0,65 0,65 0,75 0,85 0,95 1,0 16 22 0,80 0,80 0,80 0,90 1,1 1,1 22 29 0,90 0,90 0,90 1,1 1,4 1,4 29 35 1,0 1,0 1,0 1,3 1,7 1,7 35 40 1,1

39、 1,1 1,1 1,5 1,9 1,9 40 50 1,3 1,3 1,3 1,8 2,2 2,2 50 55 1,5 1,5 1,5 2,0 2,5 2,5 NOTE This specification shall be applied to the products of temper grade H112 and those finished by the hot-rolled condition.Table 2 (continued) ISO 2014 All rights reserved 3BS ISO 6361-4:2014ISO 6361-4:2014(E) Specifi

40、ed thickness Alloy number 1050, 1050A, 1070, 1070A, 1080, 1080A, 1085,1100, 1100A, 1200, 1230A, 3003, 3103, 3203, 3005, 3105, 4006, 4007, 4015, 5005, 5010, 5110A, 5050, 8011A Specified width Over Up to and including Up to and including 900 Over 900, up to and including 1 400 Over 1 400, up to and in

41、cluding 1 800 Over 1 800, up to and including 2 300 Over 2 300, up to and including 2 600 Over 2 600, up to and including 3 400 Tolerance 55 70 1,9 1,9 1,9 2,5 3,2 3,2 70 75 2,3 2,3 2,3 3,0 3,8 3,8 75 100 2,8 2,8 2,8 3,6 4,1 4,1 100 150 3,2 3,2 3,8 4,1 150 203 4,1 4,1 4,1 4,1 NOTE This specification

42、 shall be applied to the products of temper grade H112 and those finished by the hot-rolled condition. Table 4 Thickness tolerances for hot-rolled product Dimensions in millimetres Specified thickness Alloy number 2014, 2014A, 2017, 2017A, 2618A, 2219, 2024, 2124, 3004, 3104, 5021, 5026, 5040, 5042,

43、 5049, 5449, 5251, 5052, 5154, 5154A, 5254, 5454, 5754, 5456, 5059, 5070, 5082, 5182, 5083, 5383, 5086, 6016, 6025, 6061, 6082, 7204,7010, 7020, 7021, 7022, 7050, 7075, 7475, 7178 Specified width Over Up to and including Up to and including 900 Over 900, up to and including 1 400 Over 1 400, up to a

44、nd including 1 800 Over 1 800, up to and including 2 300 Over 2 300, up to and including 2 600 Over 2 600, up to and including 3 400 Tolerance 4 5 0,30 0,35 0,50 0,60 5 6 0,40 0,45 0,55 0,65 6 8 0,50 0,50 0,60 0,70 0,80 0,90 8 11 0,60 0,60 0,70 0,80 0,90 1,0 11 16 0,70 0,70 0,80 0,90 1,0 1,1 16 22 0

45、,80 0,80 0,80 0,90 1,1 1,1 22 29 0,90 0,90 0,90 1,1 1,4 1,4 29 35 1,0 1,0 1,0 1,3 1,7 1,7 35 40 1,1 1,1 1,1 1,5 1,9 1,9 40 50 1,3 1,3 1,3 1,8 2,2 2,2 50 55 1,5 1,5 1,5 2,0 2,5 2,5 55 70 1,9 1,9 1,9 2,5 3,2 3,2 70 75 2,3 2,3 2,3 3,0 3,8 3,8 NOTE This specification shall be applied to the products of

46、temper grade H112 and those finished by the hot-rolled condition.Table 3 (continued) 4 ISO 2014 All rights reservedBS ISO 6361-4:2014ISO 6361-4:2014(E) Specified thickness Alloy number 2014, 2014A, 2017, 2017A, 2618A, 2219, 2024, 2124, 3004, 3104, 5021, 5026, 5040, 5042, 5049, 5449, 5251, 5052, 5154

47、, 5154A, 5254, 5454, 5754, 5456, 5059, 5070, 5082, 5182, 5083, 5383, 5086, 6016, 6025, 6061, 6082, 7204,7010, 7020, 7021, 7022, 7050, 7075, 7475, 7178 Specified width Over Up to and including Up to and including 900 Over 900, up to and including 1 400 Over 1 400, up to and including 1 800 Over 1 800

48、, up to and including 2 300 Over 2 300, up to and including 2 600 Over 2 600, up to and including 3 400 Tolerance 75 100 2,8 2,8 2,8 3,6 4,1 4,1 100 150 3,2 3,2 3,6 4,1 4,1 150 203 4,1 4,1 4,1 4,1 4,1 NOTE This specification shall be applied to the products of temper grade H112 and those finished by the hot-rolled condition. 3.2 Width Width tolerances for shared sheet and plate