1、BSI Standards Publication BS ISO 6742-5:2015 Cycles Lighting and retro- reflective devices Part 5: Lighting systems not powered by the cycles movementBS ISO 6742-5:2015 BRITISH STANDARD National foreword This British Standard is the UK implementation of ISO 6742-5:2015. The UK participation in its p
2、reparation was entrusted to Technical Committee GME/25, Cycles. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct applicatio
3、n. The British Standards Institution 2015. Published by BSI Standards Limited 2015 ISBN 978 0 580 78229 9 ICS 43.150 Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the authority of the Standards Policy and Strategy Committe
4、e on 30 June 2015. Amendments issued since publication Date Text affectedBS ISO 6742-5:2015 ISO 2015 Cycles Lighting and retro- reflective devices Part 5: Lighting systems not powered by the cycles movement Cycles Dispositifs dclairage et dispositifs rtrorflchissants Partie 5: Systmes dclairage non
5、aliments par dynamo INTERNATIONAL STANDARD ISO 6742-5 First edition 2015-05-15 Reference number ISO 6742-5:2015(E)BS ISO 6742-5:2015ISO 6742-5:2015(E)ii ISO 2015 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO 2015, Published in Switzerland All rights reserved. Unless otherwise specified, no pa
6、rt of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member b
7、ody in the country of the requester. ISO copyright office Ch. de Blandonnet 8 CP 401 CH-1214 Vernier, Geneva, Switzerland Tel. +41 22 749 01 11 Fax +41 22 749 09 47 copyrightiso.org www.iso.orgBS ISO 6742-5:2015ISO 6742-5:2015(E)Foreword iv 1 Scope . 1 2 Normative references 1 3 Terms and definition
8、s . 1 4 Lamps and interchangeable power source . 2 4.1 General . 2 4.2 Requirement . 2 5 Lamps and dedicated power source . 2 5.1 General . 2 5.2 Requirements . 2 6 Common requirements for lighting systems . 2 6.1 Corrosion resistance 2 6.2 Water resistance 2 6.3 Low battery indicator 2 6.4 Power so
9、urce 2 7 Test method . 3 7.1 Lamps and interchangeable power source . 3 7.1.1 Lamps emitting light to the front . 3 7.1.2 Lamps emitting light to the rear . 3 7.2 Lamps and dedicated power source . 3 7.2.1 Lamps emitting light to the front . 3 7.2.2 Lamps emitting light to the rear . 3 7.3 Common te
10、st methods for lighting systems 3 7.3.1 Corrosion testing . 3 7.3.2 Water resistance . 3 8 Instructions 3 9 Marking 4 9.1 Requirement . 4 9.2 Durability test 4 9.2.1 Requirement 4 9.2.2 Test method 4 Bibliography 5 ISO 2015 All rights reserved iii Contents PageBS ISO 6742-5:2015ISO 6742-5:2015(E) Fo
11、reword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a tec
12、hnical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters o
13、f electrotechnical standardization. The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This documen
14、t was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such
15、 patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any trade name used in this document is information given for the convenience of users and does
16、 not constitute an endorsement. For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT), see the following URL: Foreword Supplementary informat
17、ion. The committee responsible for this document is ISO/TC 149, Cycles, Subcommittee SC 1, Cycles and major sub-assemblies. I S O 6742 consists of the following parts, under the general title C yc le s Light ing an d r e t r o -r e f le c t i ve d e v ic e s: Part 1: Lighting and light signalling de
18、vices Part 2: Retro reflective devices Part 3: Installation and use of lighting and retro-reflective devices Part 4: Lighting systems powered by the cycles movement Part 5: Lighting systems not powered by the cycles movementiv ISO 2015 All rights reservedBS ISO 6742-5:2015INTERNATIONAL ST ANDARD ISO
19、 6742-5:2015(E) Cycles Lighting and retro-reflective devices Part 5: Lighting systems not powered by the cycles movement 1 Scope This part of ISO 6742 is applicable to lighting systems used on cycles intended to be used on public roads and, especially, bicycles complying with ISO 4210 and ISO 8098.
20、This part of ISO 6742 specifies requirements and test methods for the performance of lighting systems not powered by the cycles movement. It applies to light devices complying with ISO 6742-1. Lighting systems include lighting devices and power not supplied by cycles movement such as battery. 2 Norm
21、ative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments)
22、 applies. ISO 6742-1:2015, C ycle s Light ing and re t r o-ref le c t i ve de v ice s Par t 1: Light ing and light s ignalling de v ice s ISO 9227, Corrosion tests in artificial atmospheres Salt spray tests IEC 60086, Primary batteries IEC 60529, Degrees of protection provided by enclosures (IP Code
23、) IEC 61960, Secondary cells and batteries containing alkaline or other non-acid electrolytes Secondary lithium cells and batteries for portable applications IEC 62133, S e c o n d a r y c e l l s a n d b a t t e r i e s c o n t a i n i n g a l k a l i n e o r o t h e r n o n - a c i d e l e c t r o
24、 l y t e s S a f e t y r e q u i r e m e n t s for portable sealed secondary cells, and for batteries made from them, for use in portable applications 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 6742-1 and the following apply. 3.1 integrated lamp
25、 and power source system including power source and at least one type of light designed to be used together 3.2 lamps and interchangeable power source open system system working with a power source corresponding to the properties specified by the light manufacturer 3.3 lamps and dedicated power sour
26、ce closed system system including the power source specified by the light manufacturer ISO 2015 All rights reserved 1BS ISO 6742-5:2015ISO 6742-5:2015(E) 3.4 battery pack cell assembly, battery management system and casing designed or specified by light manufacturer 4 Lamps and interchangeable power
27、 source 4.1 General The complete system shall be designed as closed system which does not have compatibility between lamps and power source. 4.2 Requirement When tested by the method described in 7.1 and 7.3, lamps with interchangeable power source shall correspond with the requirements of Clause 6
28、and ISO 6742-1:2015, Clause 4. 5 Lamps and dedicated power source 5.1 General The complete system shall be designed as open system which requires compatibility between lamps and power source. 5.2 Requirements When tested by the method described in 7.2 and 7.3 , lamps with dedicated power source shal
29、l correspond with the requirements of Clause 6 and ISO 6742-1:2015, Clause 4. 6 Common requirements for lighting systems 6.1 Corrosion resistance The lighting equipment shall still be functional after testing has taken place. 6.2 Water resistance The lighting equipment shall still be functional afte
30、r testing has taken place. 6.3 Low battery indicator The lighting system shall include a low battery indicator or state of charge indicator. This indicator shall be located on the lamp, on the battery case or on display, clearly and easily visible. The indicator shall be activated at the latest when
31、 the photometrical requirements of ISO 6742-1 are not fulfilled anymore. The lamp shall emit light for at least 30 min after activation of the indicator. 6.4 Power source Battery or any kind of power source shall comply with the requirement of IEC 60086, IEC 61960, and IEC 62133 if applicable.2 ISO
32、2015 All rights reservedBS ISO 6742-5:2015ISO 6742-5:2015(E) 7 Test method 7.1 Lamps and interchangeable power source 7.1.1 Lamps emitting light to the front Lamps have to be tested corresponding with the test methods of ISO 6742-1:2015, 4.2 (Front position lamp), 4.5 (Low beam), 4.6 (High beam) and
33、 4.7 (Direction indicators). The test voltage shall be the rated voltage of power source. 7.1.2 Lamps emitting light to the rear Rear lights have to be tested corresponding with the test methods of ISO 6742-1:2015, 4.3 (Rear lamp), 4.4 (Stop lamp), 4.7 (Direction indicators) and 4.8 (Stand light). T
34、he test voltage shall be the rated voltage of power source. 7.2 Lamps and dedicated power source 7.2.1 Lamps emitting light to the front Lamps have to be tested corresponding with the test methods of ISO 6742-1:2015, 4.2 (Front position lamp), 4.5 (Low beam), 4.6 (High beam) and 4.7 (Direction indic
35、ators). The test voltage shall be the rated voltage of power source or dedicated power source. 7.2.2 Lamps emitting light to the rear Rear lights have to be tested corresponding with the test methods of ISO 6742-1:2015, 4.3 (Rear lamp), 4.4 (Stop lamp), 4.7 (Direction indicators) and 4.8 (Stand ligh
36、t). The test voltage shall be the rated voltage of power source or dedicated power source. 7.3 Common test methods for lighting systems 7.3.1 Corrosion testing The entire lighting system (front lights, rear lights in functional assembly conditions) shall undergo corrosion testing according to ISO 92
37、27. A total of 96 h shall be run with a salt concentration of 5 %. 7.3.2 Water resistance Battery rear lights in functional assembly conditions shall undergo water spray testing according to IEC 60529, regarding class IPX4: protection against water sprays. Battery front lights shall fulfil the class
38、 IPX4. At the end of the test allow the unit to drain for 1 h. 8 Instructions The instructions shall be provided with lighting devices. These instructions can be provided in all type of format (paper, CD, website) according to national regulations and shall be written in the language of the country
39、where the lighting device is to be marketed or by visual tools, such as pictograms and illustrations shall feature prominently in the product safety information. When an electronic format is provided, a paper version shall be available upon request. The customer shall be made aware of this informati
40、on either by the manufacturer or the retailer. Instructions for use shall contain the following information on: a) type of lamp; ISO 2015 All rights reserved 3BS ISO 6742-5:2015ISO 6742-5:2015(E) b) method for fitting the equipment to the bicycle; c) compatibility (output, input, connection) for ope
41、n system; d) operation and adjustment. Additional information may be provided at the discretion of the manufacturer. For closed system, the incompatibility of lamps and power sources shall be stated in the instructions. 9 Marking 9.1 Requirement The lamp and/or power source shall be durably marked w
42、ith: a) the manufacturers name, abbreviation or trade-mark; b) the model name, production number, symbol or other identification; c) the rated input, output power, battery type, or anything to describe compatibility for open system. Marking a) shall appear on the surfaces which is visible after asse
43、mbled on the bicycle, in characters not less than 1 mm in height. 9.2 Durability test 9.2.1 Requirement When tested by the method described in 9.2.2, the marking shall remain easily legible. It shall not be easily possible to remove any label nor shall any label show any sign of curling. 9.2.2 Test
44、method Rub the marking by hand for 15 s with a piece of cloth soaked in water and again for 15 s with a piece of cloth soaked in petroleum spirit.4 ISO 2015 All rights reservedBS ISO 6742-5:2015ISO 6742-5:2015(E) Bibliography 1 ISO 4210 (all parts), Cycles Safety requirements for bicycles 2 ISO 8098
45、, Cycles Safety requirements for bicycles for young children ISO 2015 All rights reserved 5BS ISO 6742-5:2015ISO 6742-5:2015(E) ISO 2015 All rights reserved ICS 43.150 Price based on 5 pagesThis page deliberately left blankBSI is the national body responsible for preparing British Standards and othe
46、r standards-related publications, information and services. BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited. British Standards Institution (BSI) BSI Group Headquarters 389 Chiswick High Road London W4 4AL UK About us W
47、e bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions. The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation pr
48、ocess. Organizations of all sizes and across all sectors choose standards to help them achieve their goals. Information on standards We can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Cust
49、omer Services team or Knowledge Centre. Buying standards You can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team. Subscriptions Our range of subscription service
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1