BS ISO 6752-2008 en_3866 Tools for pressing - Round punches with 60 degrees conical head and straight shank《冲压工具.带60°圆锥头和直柄的圆冲头》.pdf

1、BS ISO 6752:2008 ICS 25.120.10 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BRITISH STANDARD Tools for pressing Round punches with 60 degrees conical head and straight shankThis British Standard was published under the authority of the Standards Policy and Strategy Committe

2、e on 3 2008 BSI 2008 ISBN 978 0 580 57365 1 Amendments/corrigenda issued since publication Date Comments BS ISO 6752:2008 National foreword This British Standard is the UK implementation of ISO 6752:2008. It supersedes BS 7568-7:1992 which is withdrawn. The UK participation in its preparation was en

3、trusted to Technical Committee MTE/12, Tools for pressing and moulding. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct ap

4、plication. Compliance with a British Standard cannot confer immunity from legal obligations. 0 SeptemberBS ISO 6752:2008Reference number ISO 6752:2008(E) ISO 2008INTERNATIONAL STANDARD ISO 6752 Second edition 2008-06-15 Tools for pressing Round punches with 60 degrees conical head and straight shank

5、 Outillage de presse Poinons tte conique 60 degrs et corps cylindrique BS ISO 6752:2008 ISO 6752:2008(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are

6、embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorpora

7、ted. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a

8、problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2008 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, i

9、ncluding photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Pub

10、lished in Switzerland ii ISO 2008 All rights reservedBS ISO 6752:2008 ISO 6752:2008(E) ISO 2008 All rights reserved iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International St

11、andards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also

12、 take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committee

13、s is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possib

14、ility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 6752 was prepared by Technical Committee ISO/TC 29, Small tools, Subcommittee SC 8, Tools for pressing and moulding. This second

15、edition cancels and replaces the first edition (ISO 6752:1984), which has been technically revised. BS ISO 6752:2008BS ISO 6752:2008 INTERNATIONAL STANDARD ISO 6752:2008(E) ISO 2008 All rights reserved 1 Tools for pressing Round punches with 60 degrees conical head and straight shank 1 Scope This In

16、ternational Standard specifies the basic dimensions, in millimetres, of round punches with 60 conical head and straight shank in the diameter range of 0,5 mm to 20 mm. It gives example material and hardness values, and specifies the designation of the punches, whose main use is punching holes in ste

17、el sheets but that can also be used on other materials. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (inclu

18、ding any amendments) applies. ISO 2768-1:1989, General tolerances Part 1: Tolerances for linear and angular dimensions without individual tolerance indications 3 Dimensions The dimensions of round punches with 60 conical head and straight shank shall conform to the indications of Figure 1 and Table

19、1. General tolerance: ISO 2768-m Surface roughness values in micrometres Figure 1 Round punches with 60 conical head and straight shank BS ISO 6752:2008 ISO 6752:2008(E) 2 ISO 2008 All rights reservedTable 1 Dimensions of round punches with 60 conical head and straight shank L 0,5 0 +D 1 h6 D 2H 0,2

20、 0 +r 71 80 100 0,50 0,9 0,55 1,0 0,60 1,1 0,65 1,2 0,70 1,3 0,75 1,3 0,2 0,80 1,4 0,85 1,4 0,90 1,6 0,95 1,6 0,4 0,2 0,2 0 + 1,0 1,8 1,1 1,8 1,2 2,0 1,3 2,0 1,4 2,2 1,5 2,2 1,6 2,5 1,7 2,5 1,8 2,8 1,9 2,8 2,0 3,0 2,1 3,2 2,2 3,2 2,3 3,5 2,4 3,5 2,5 3,5 2,6 4,0 2,7 4,0 2,8 4,0 2,9 4,0 0,5 0,4 0,3 0

21、+ BS ISO 6752:2008 ISO 6752:2008(E) ISO 2008 All rights reserved 3 Table 1 (continued) L 0,5 0 +D 1 h6 D 2H 0,2 0 +r 71 80 100 3,0 4,5 3,1 4,5 3,2 4,5 3,3 4,5 3,4 4,5 3,5 5,0 3,6 5,0 3,7 5,0 3,8 5,0 3,9 5,0 4,0 5,5 4,1 5,5 4,2 5,5 4,3 5,5 4,4 5,5 4,5 6,0 4,6 6,0 4,7 6,0 4,8 6,0 4,9 6,0 5,0 6,5 5,1 6

22、,5 5,2 6,5 5,3 6,5 5,4 6,5 5,5 7,0 5,6 7,0 5,7 7,0 5,8 7,0 5,9 7,0 6,0 8,0 0,5 0,6 0,4 0 + BS ISO 6752:2008 ISO 6752:2008(E) 4 ISO 2008 All rights reservedTable 1 (continued) L 0,5 0 +D 1 h6 D 2H 0,2 0 +r 71 80 100 6,1 8,0 6,2 8,0 6,3 8,0 6,4 8,0 0,5 6,5 9,0 7,0 9,0 7,5 10,0 8,0 10,0 8,5 11,0 9,0 11

23、,0 9,5 12,0 10,0 12,0 10,5 13,0 11,0 13,0 11,5 14,0 12,0 14,0 12,5 15,0 13,0 15,0 1 1 0,5 0 + 13,5 16,0 14,0 16,0 14,5 17,0 15 17,0 15,5 18,0 16,0 18,0 17,0 19,0 18,0 20,0 19,0 21,0 20,0 22,0 1,5 1,5 0,5 0 + BS ISO 6752:2008 ISO 6752:2008(E) ISO 2008 All rights reserved 5 4 Material and hardness The

24、 material is left to the manufacturers discretion. The following hardness values are given as examples. a) Alloyed cold work steel with 5 % to 12 % Cr: point: (60 2) HRC; head: (45 5) HRC. b) High-speed steel: point: (62 2) HRC; head: (52 5) HRC. 5 Designation A round punch with 60 conical head and

25、straight shank in accordance with this International Standard shall be designated by: a) “Punch”; b) reference to this International Standard, i.e. ISO 6752; c) its points diameter, D 1 , in millimetres; d) its length, L, in millimetres. EXAMPLE Punch ISO 6752 - 6,3 80 BS ISO 6752:2008 ISO 6752:2008

26、(E) ICS 25.120.10 Price based on 5 pages ISO 2008 All rights reserved BS ISO 6752:2008 This page has been intentionally left blankBS ISO 6752:2008 BSI Group Headquarters 389 Chiswick High Road, London, W4 4AL, UK Tel +44 (0)20 8996 9001 Fax +44 (0)20 8996 7001 standards BSI - British Standards Inst

27、itution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards s

28、hould make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical comm

29、ittee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards O

30、rders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001 Email: You may also buy directly using a debit/credit card from the BSI Shop on the Website http:/ In response to orders for international

31、 standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical

32、Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact Information Centre. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: Subscribing members of BSI are kept up to date with standards developme

33、nts and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via British Standards Online can be

34、found at http:/ Further information about BSI is available on the BSI website at http:/ Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs an

35、d Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of nec

36、essary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright and Licensing Manager. Tel: +44 (0)20 8996 7070 Email: