BS ISO 7299-2-2009 en_8540 Diesel engines - End-mounting flanges for pumps - High-pressure supply pumps for common rail fuel injection systems《柴油发动机.泵端面安装法兰.公轨燃料喷射系统用高压供给泵》.pdf

1、BS ISO 7299-2:2009 ICS 43.060.40 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BRITISH STANDARD Diesel engines End- mounting flanges for pumps Part 2: High-pressure supply pumps for common rail fuel injection systemsThis British Standard was published under the authority of

2、the Standards Policy and Strategy Committee on 31 August 2009 BSI 2009 ISBN 978 0 580 56840 4 Amendments/corrigenda issued since publication Date Comments BS ISO 7299-2:2009 National foreword This British Standard is the UK implementation of ISO 7299-2:2009. Together with BS ISO 7299-1:2007, it supe

3、rsedes BS ISO 7299:1996 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee MCE/22, Engines for road vehicles. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include

4、all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations.BS ISO 7299-2:2009Reference number ISO 7299-2:2009(E) ISO 2009INTERNATIONAL STANDARD ISO 7299-2 First edition 2009-02-15 Die

5、sel engines End-mounting flanges for pumps Part 2: High-pressure supply pumps for common rail fuel injection systems Moteurs diesels Brides de montage des pompes Partie 2: Pompes dalimentation haute pression pour systmes dinjection de combustible rampe commune BS ISO 7299-2:2009 ISO 7299-2:2009(E) P

6、DF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, p

7、arties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relati

8、ve to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIG

9、HT PROTECTED DOCUMENT ISO 2009 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or

10、 ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2009 All rights reservedBS ISO 7299-2:2009 ISO 7299-2:2009(E) ISO 2009 All ri

11、ghts reserved iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a sub

12、ject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (I

13、EC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical commit

14、tees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be

15、 held responsible for identifying any or all such patent rights. ISO 7299-2 was prepared by Technical Committee ISO/TC 22, Road vehicles, Subcommittee SC 7, Injection equipment and filters for use on road vehicles. This first edition of ISO 7299-2, together with ISO 7299-1:2007, cancels and replaces

16、 ISO 7299:1996, which has been technically revised. ISO 7299 consists of the following parts, under the general title Diesel engines End-mounting flanges for pumps: Part 1: Fuel injection pumps Part 2: High-pressure supply pumps for common rail fuel injection systems BS ISO 7299-2:2009BS ISO 7299-2:

17、2009 INTERNATIONAL STANDARD ISO 7299-2:2009(E) ISO 2009 All rights reserved 1 Diesel engines End-mounting flanges for pumps Part 2: High-pressure supply pumps for common rail fuel injection systems 1 Scope This part of ISO 7299 specifies dimensional requirements for seven types of end-mounting flang

18、es of high- pressure supply pumps for common rail fuel injection systems for use in diesel (compression-ignition) engines. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undat

19、ed references, the latest edition of the referenced document (including any amendments) applies. ISO 6519, Diesel engines Fuel injection pumps Tapers for shaft ends and hubs 3 Dimensions and tolerances 3.1 General Engine manufacturers should use the tolerance H7 for the female register diameter. In

20、the figures and tables, except for Figures 2 and 5 and Tables 2 and 5 (shaft end with tang drive), the diameter d 2corresponds to the diameter d specified in ISO 6519. NOTE The flange configuration can optionally be rotated relative to the pump housing. BS ISO 7299-2:2009 ISO 7299-2:2009(E) 2 ISO 20

21、09 All rights reserved3.2 High-pressure supply pumps 3.2.1 Type 1 end-mounting flange See Figure 1 and Table 1. Dimensions in millimetres Figure 1 Table 1 Dimensions in millimetres l 2d 1f7 d 2nom. d 3nom. d 4max. d 5l 1 0,5 min. max. l 3nom. 50 20 98 125 8,5 to 9,3 26 23,5 24,5 15 BS ISO 7299-2:200

22、9 ISO 7299-2:2009(E) ISO 2009 All rights reserved 3 3.2.2 Type 2 end-mounting flange (with tang drive) See Figure 2 and Table 2. Dimensions in millimetres Figure 2 Table 2 Dimensions in millimetres d 1f7 d 2nom. d 3nom. d 4max. d 5l 1 1 l 2max. l 3nom. l 4 1 l 5f7 50 23 98 125 8,5 to 9,3 21,8 20,7 1

23、5 38,9 10 BS ISO 7299-2:2009 ISO 7299-2:2009(E) 4 ISO 2009 All rights reserved3.2.3 Type 3 end-mounting flange See Figure 3 and Table 3. Dimensions in millimetres Figure 3 Table 3 Dimensions in millimetres d 5l 2d 1f7 d 2nom. d 3nom. d 4max. drilled threaded a l 1 0,5 min. max. l 3nom. 50 98 125 8,5

24、 to 9,3 14 12 13 15 68 20 90 116 8,5 to 9,3 M8 1,25 6H25,7 18 24 15 or 17 aOptional. BS ISO 7299-2:2009 ISO 7299-2:2009(E) ISO 2009 All rights reserved 5 3.2.4 Type 4 end-mounting flange See Figure 4 and Table 4. Dimensions in millimetres aThis figure shows requirements for the position of the three

25、 mounting holes. The actual configuration of the flange depends on design requirements. Figure 4 Table 4 Dimensions in millimetres d 5d 1f7 d 2nom. d 3nom. drilled (nom.) threaded al 1nom. l 2l 3nom. 12 to 14 13 max. 50 or 68 20, 22 or 25 22 to 26,5 24,5 max. 68 or 80 98 8,5 to 9,4 107 25 130 10,5 M

26、8 1,25 6H 12 to 26,5 10,2 to 24,5 11 to 27 a Optional. BS ISO 7299-2:2009 ISO 7299-2:2009(E) 6 ISO 2009 All rights reserved3.2.5 Type 5 end-mounting flange (with tang drive) See Figure 5 and Table 5. Dimensions in millimetres aThis figure shows requirements for the position of the three mounting hol

27、es. The actual configuration of the flange depends on design requirements. Figure 5 Table 5 Dimensions in millimetres d 5d 1f7 d 2nom. d 3nom. drilled (nom.) threaded al 1nom. l 2max. l 3nom. l 4nom. l 5f7 20 9,4 M6 1 6H 16,85 14,1 9 98 8,5 to 9,4 19 to 24,5 50 20, 22 or 25 82 7,8 M8 1,25 6H 21,3 to

28、 23 21,1 7,3 31,5 8 aOptional. BS ISO 7299-2:2009 ISO 7299-2:2009(E) ISO 2009 All rights reserved 7 3.2.6 Type 6 end-mounting flange See Figure 6 and Table 6. Dimensions in millimetres aDetail X (optional). Figure 6 Table 6 Dimensions in millimetres l 2l 4d 1d 2nom. d 3nom. d 4max. d 5H13 l 1 0,6 mi

29、n. max. l 3nom. min. max. 0,019 0,065 0,024 0,070 21,35 19,25 20,45 6,65 8,65 11,05 50 0,019 0,065 25 105 131 9 21,35 9,25 9,85 17,9 2,5 3,5 BS ISO 7299-2:2009 ISO 7299-2:2009(E) 8 ISO 2009 All rights reserved3.2.7 Type 7 end-mounting flange See Figure 7 and Table 7. Figure 7 Table 7 Dimensions in m

30、illimetres Angles in degrees l 2d 1f7 d 2nom. d 3 0,3 d 4max. d 5 l 1min. max. l 3nom. l 4nom. 0,5 0,5 25 16,2 to 16,8 14,5 15,7 30 10,7 to 10,9 13,2 to 13,8 10,5 12,0 19 59 40 20 45 30 30 or 35 62 40 20 107 35 130 155,4 10,5 to 10,8 12,9 to 14,2 11,4 11,8 18 56 45 30 BS ISO 7299-2:2009 ISO 7299-2:2

31、009(E) ISO 2009 All rights reserved 9 Bibliography 1 ISO 261, ISO general purpose metric screw threads General plan 2 ISO 286-2, ISO system of limits and fits Part 2: Tables of standard tolerance grades and limit deviations for holes and shafts 3 ISO 965-1, ISO general-purpose metric screw threads T

32、olerances Part 1: Principles and basic data BS ISO 7299-2:2009 ISO 7299-2:2009(E) ICS 43.060.40 Price based on 9 pages ISO 2009 All rights reserved BS ISO 7299-2:2009 This page has been intentionally left blankBS ISO 7299-2:2009 BSI Group Headquarters 389 Chiswick High Road, London, W4 4AL, UK Tel +

33、44 (0)20 8996 9001 Fax +44 (0)20 8996 7001 standards BSI - British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions Br

34、itish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity

35、while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subs

36、cribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001 Email: You may also buy directly using a debit/credit ca

37、rd from the BSI Shop on the Website http:/ In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on nat

38、ional, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact Information Centre. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 70

39、48 Email: Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information

40、 regarding online access to British Standards via British Standards Online can be found at http:/ Further information about BSI is available on the BSI website at http:/ Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the interna

41、tional standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This

42、does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright and Licensing Manager. Tel: +44 (0)20 8996 7070 Email: