BS ISO 7588-2-1999 en_7845 Road vehicles - Electrical electronic switching devices - Electronic devices《道路车辆.电气 电子开关设备.第2部分 电子设备》.pdf

1、BRITISH STANDARD BS ISO 7588-2:1998 Road vehicles Electrical/electronic switching devices Part 2: Electronic devices ICS 43.040.10BS ISO7588-2:1998 This British Standard, having been prepared under the directionof the Engineering SectorCommittee, was publishedunder the authority ofthe Standards Comm

2、ittee andcomes into effect on 15February1999 BSI 07-1999 ISBN 0 580 30949 5 National foreword This British Standard reproduces verbatimISO7588-2:1998 and implements it as the UK national standard. The UK participation in its preparation was entrusted to Technical Committee AUE/16, Electrical and ele

3、ctronic equipment, which has the responsibility to: aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developme

4、nts and promulgate them in the UK. A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue

5、 under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their corre

6、ct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, theISO title page, pages ii to iv, pages 1 to 5 and a back cover. This standard has been update

7、d (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Amendments issued since publication Amd. No. Date CommentsBS ISO7588-2:1998 BSI 07-1999 i Contents Page National foreword Inside front cover Foreword iii Text of

8、ISO 7588-2 1ii blankBS ISO7588-2:1998 ii BSI 07-1999 Contents Page Foreword iii 1 Scope 1 2 Normative references 1 3 Definitions 1 4 Dimensions and other requirements 1 5 Functional allocation of electronic device terminals 3 6 Designation 3 Annex A (informative) Dimensions of socket apertures 4 Ann

9、ex B (informative) Recommended practice for terminal identification of electronic devices viewed from the terminal connection side 5 Figure 1 1 Figure 2 2 Figure 3 2 Figure A.1 4 Figure B.1 5 Table 1 3BS ISO7588-2:1998 BSI 07-1999 iii Foreword ISO (the International Organization for Standardization)

10、 is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be repre

11、sented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. Draft International Standar

12、ds adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75% of the member bodies casting a vote. International StandardISO7588-2 was prepared by Technical Committee ISO/TC22, Road vehicles, Subcommi

13、tteeSC3, Electrical and electronic equipment. ISO7588 consists of the following parts, under the general title Road vehicles Electrical/electronic switching devices: Part 1: Relays and flashers; Part 2: Electronic devices; Part 3: Microrelays. Annex A and Annex B of this part ofISO7588 are for infor

14、mation only. Descriptors: Road vehicles, motor vehicles, electronic equipment, electronic switches, electronic terminals, electric contacts, form specifications, dimensions, overall dimensions, position (location), contact allocation, designation.iv blankBS ISO7588-2:1998 BSI 07-1999 1 1 Scope This

15、part ofISO7588 specifies dimensional characteristics of electronic devices intended for road vehicles. Annex A gives additional information on the dimensions of socket apertures and Annex B gives recommended terminal identification. 2 Normatives references The following standards contain provisions

16、which, through reference in this text, constitute provisions of this part ofISO7588. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this part ofISO7588 are encouraged to investigate the possibility of applying

17、the most recent editions of the standards indicated below. Members of IEC and ISO maintain registers of currently valid International Standards. ISO 8092-1:1996, Road vehicles Connections for on-board electrical wiring harnesses Part 1: Tabs for single-pole connections Dimensions and specific requir

18、ements. ISO 8092-2:, Road vehicles Connections for on-board electrical wiring harnesses Part 2: Definitions, test methods and general performance requirements 1) . 3 Definitions For the purposes of this part ofISO7588, the definitions given in ISO8092-2 apply. 4 Dimensions and other requirements 4.1

19、 General Dimensional characteristics and other requirements are specified in4.2 to4.4. NOTEAll corresponding dimensions also apply if less than nine tabs are fitted. The dimensions of socket apertures given in Annex A are for information only. 4.2 Positioning zones of the tabs and socket apertures 4

20、.2.1 Location of tabs and apertures True position SeeFigure 1. 1) To be published. (Revision ofISO8092-2:1996) Figure 1 BS ISO7588-2:1998 2 BSI 07-1999 4.2.2 Dimensional limits of the tabs SeeFigure 2. The tabs shall be in accordance withISO8092-1, sizes6,3 0,8, and 2,8 0,8 respectively, and shall n

21、ot have shoulders. 4.3 Overall dimensions and other requirements for electronic devices SeeFigure 3 and Table 1. Configurations other than rectangular are permitted, provided they lie within the specified area. However, in all cases the outside contour shall lie within the dimensions X and Y (maximu

22、m) given inFigure 3 and inTable 1. Figure 2 Figure 3 BS ISO7588-2:1998 BSI 07-1999 3 Table 1 4.4 Other requirements for sockets 4.4.1 Apertures at the entering plane shall be in accordance with Figure 1 and shall accept tabs to the maximum limits. 4.4.2 In order to avoid the need for excessive withd

23、rawal force, it is recommended that the female connectors in the socket should not incorporate detents. 5 Functional allocation of electronic device terminals No functional allocation of terminals has been established for this part ofISO7588. No terminal identification has been specified but a recom

24、mended practice is given inAnnex B. 6 Designation Electronic devices in accordance with this part ofISO7588 shall be designated as shown in the following example. EXAMPLE NOTEA manufacturers reference number should be used to identify products with differing functional allocation. Dimensions in mill

25、imetres Size type X Y 1 Y 2 Z max. max. max. max. C 15,3 5,0 25,7 55 D 17 9,6 30,3 55 E 20 9,6 30,3 55BS ISO7588-2:1998 4 BSI 07-1999 Annex A (informative) Dimensions of socket apertures A.1 General This annex is for information only, pending completion of current ISO work on dimensions of socket ap

26、ertures. A definitive specification may be given in a future edition of this part ofISO7588. A.2 Dimensions of socket apertures Socket apertures should accommodate the following tab positioning zones (seeFigure A.1): at entering plane: 7,3mm 1,6mm for tab size 6,3 0,8; 3,8mm 1,6mm for tab size 2,8 0

27、,8; at throat: 6,7mm 1,0mm for tab size6,3 0,8; 3,2mm 1,0mm for tab size2,8 0,8. Figure A.1 BS ISO7588-2:1998 BSI 07-1999 5 Annex B (informative) Recommended practice for terminal identification of electronic devices viewed from the terminal connection side SeeFigure B.1. The five large terminals sh

28、ould be identified in accordance with ISO7588-1. The four small terminals should be identified with letters to differentiate them from existing manufacturers numbers. Figure B.1 BS ISO 7588-2:1998 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national

29、 body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the late

30、st amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which ca

31、n be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards public

32、ations should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI prov

33、ides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:

34、02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyri

35、ght subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the internationalstandardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form o

36、r by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.