BS ISO 7755-2-2013 en_5172 Hardmetal burrs Cylindrical burrs (style A)《硬质合金去毛刺锉.圆柱形锉(A款)》.pdf

1、BSI Standards Publication BS ISO 7755-2:2013 Hardmetal burrs Part 2: Cylindrical burrs (style A)BS ISO 7755-2:2013 BRITISH STANDARD National foreword This British Standard is the UK implementation of ISO 7755-2:2013. The UK participation in its preparation was entrusted to Technical Committee MTE/18

2、, Tools tips and inserts for cutting applications. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The Britis

3、h Standards Institution 2013. Published by BSI Standards Limited 2013 ISBN 978 0 580 80969 9 ICS 25.100.20 Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 Au

4、gust 2013. Amendments issued since publication Date Text affectedBS ISO 7755-2:2013 ISO 2013 Hardmetal burrs Part 2: Cylindrical burrs (style A) Fraises-limes en mtaux-durs Partie 2: Fraises-limes cylindriques (forme A) INTERNATIONAL STANDARD ISO 7755-2 Second edition 2013-08-15 Reference number ISO

5、 7755-2:2013(E)BS ISO 7755-2:2013ISO 7755-2:2013(E)ii ISO 2013 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO 2013 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, includi

6、ng photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 2

7、2 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in SwitzerlandBS ISO 7755-2:2013ISO 7755-2:2013(E) ISO 2013 All rights reserved iii Contents Page Foreword iv 1 Scope . 1 2 Normative references 1 3 Dimensions . 1 Annex A (informative) Relationship between designations in this part of IS

8、O 7755 and the ISO 13399 series . 2 Bibliography 3BS ISO 7755-2:2013ISO 7755-2:2013(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out t

9、hrough ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO colla

10、borates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approv

11、al criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2. www.iso.org/directives Attention is drawn to the possibility that some of the elements of this document may be the subject

12、of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received. www.iso.org/patents Any trade name use

13、d in this document is information given for the convenience of users and does not constitute an endorsement. The committee responsible for this document is ISO/TC 29, Small tools, Subcommittee SC 9, Tools with cutting edges made of hard cutting materials. This second edition cancels and replaces the

14、 first edition (ISO 7755-2:1984), of which it constitutes a minor revision. ISO 7755 consists of the following parts, under the general title Hardmetal burrs: Part 1: General specifications Part 2: Cylindrical burrs (style A) Part 3: Cylindrical round- (ball-) nose burrs (style C) Part 4: Spherical

15、burrs (style D) Part 5: Oval burrs (style E) Part 6: Arch round- (ball-) nose burrs (style F) Part 7: Arch pointed-nose burrs (style G) Part 8: Flame burrs (style H) Part 9: 60 and 90 cone burrs (styles J and K) Part 10: Conical round- (ball-) nose burrs (style L) Part 11: Conical pointed-nose burrs

16、 (style M) Part 12: Inverted cone burrs (style N)iv ISO 2013 All rights reservedBS ISO 7755-2:2013INTERNATIONAL ST ANDARD ISO 7755-2:2013(E) Hardmetal burrs Part 2: Cylindrical burrs (style A) 1 Scope This part of ISO 7755 specifies the main dimensions of the cutting part for hardmetal burrs of cyli

17、ndrical shape and designated by the symbol A. Tolerances on the cutting diameter, direction of helix and cut, diameter and length of the cylindrical shank and designation of burrs are dealt with in ISO 7755-1. 2 Normative references The following documents, in whole or in part, are normatively refer

18、enced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 7755-1, Hardmetal burrs Part 1: General specifications 3 Dimensions Se

19、e Figure 1 and Table 1. Tolerances on the cutting diameter, direction of helix and cut, diameter and length of the cylindrical shank and designation of burrs are specified in ISO 7755-1. d l Figure 1 Hardmetal burr, style A Table 1 Dimensions Dimensions in millimetres d l 2 10 3 13 4 13 6 16 8 20 10

20、 20 12 25 16 25 ISO 2013 All rights reserved 1BS ISO 7755-2:2013ISO 7755-2:2013(E) Annex A (informative) Relationship between designations in this part of ISO 7755 and the ISO 13399 series For the relationship between designations in this part of ISO 7755 and preferred symbols according to the ISO 1

21、3399 series, see Table A.1. Table A.1 Relationship between designations in this part of ISO 7755 and the ISO 13399 series Symbol in this part of ISO 7755 (ISO 7755-2) Reference in this part of ISO 7755 (ISO 7755-2) Property name in the ISO 13399 series Symbol in the ISO 13399 series Reference in the

22、 ISO 13399 series d Clause 3 Cutting diameter DC ISO/TS 13399-3 71E57F l Clause 3 Cutting edge length L ISO/TS 13399-3 71DD6C95DA49B2 ISO 2013 All rights reservedBS ISO 7755-2:2013ISO 7755-2:2013(E) Bibliography 1 ISO 13399 (all parts), Cutting tool data representation and exchange ISO 2013 All righ

23、ts reserved 3BS ISO 7755-2:2013ISO 7755-2:2013(E) ISO 2013 All rights reserved IC S 25.100.20 Price based on 3 pagesThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services. BSI is incorpo

24、rated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited. British Standards Institution (BSI) BSI Group Headquarters 389 Chiswick High Road London W4 4AL UK About us We bring together business, industry, government, consumers, innovators and

25、 others to shape their combined experience and expertise into standards -based solutions. The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards

26、to help them achieve their goals. Information on standards We can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre. Buying standards You can buy and d

27、ownload PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered fr

28、om our Customer Services team. Subscriptions Our range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to With British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European

29、and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a B

30、SI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit With

31、a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is current. For further information, email . Revisions Our B

32、ritish Standards and other publications are updated by amendment or revision. We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre. Copyri

33、ght All the data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such

34、information to BSI for commercial publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written pe

35、rmission from BSI. Details and advice can be obtained from the Copyright & Licensing Department. Useful Contacts: Customer Services Tel: +44 845 086 9001 Email (orders): Email (enquiries): Subscriptions Tel: +44 845 086 9001 Email: Knowledge Centre Tel: +44 20 8996 7004 Email: Copyright & Licensing Tel: +44 20 8996 7070 Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW