BS ISO 8139-2009 Pneumatic fluid power - Cylinders 1000 kPa (10 bar) series - Mounting dimensions of rod-end spherical eyes《气动流体动力 1000 kPa(10 bar)系列气瓶 杆端球面孔的安装尺寸规格》.pdf

1、BS ISO 8139:2009 ICS 23.100.20 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BRITISH STANDARD Pneumatic fluid power Cylinders, 1 000 kPa (10 bar) series Mounting dimensions of rod-end spherical eyesThis British Standard was published under the authority of the Standards Poli

2、cy and Strategy Committee on 30 June 2009. BSI 2009 ISBN 978 0 580 63558 8 Amendments/corrigenda issued since publication Date Comments BS ISO 8139:2009 National foreword This British Standard is the UK implementation of ISO 8139:2009. It supersedes BS ISO 8139:1991 which is withdrawn. The UK partic

3、ipation in its preparation was entrusted to Technical Committee MCE/18/-/3, Cylinders. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for

4、 its correct application. Compliance with a British Standard cannot confer immunity from legal obligations.BS ISO 8139:2009Reference number ISO 8139:2009(E) ISO 2009INTERNATIONAL STANDARD ISO 8139 Third edition 2009-04-01 Pneumatic fluid power Cylinders, 1 000 kPa (10 bar) series Mounting dimensions

5、 of rod-end spherical eyes Transmissions pneumatiques Vrins, srie 1 000 kPa (10 bar) Dimensions dinterchangeabilit des tenons rotule dextrmit de tige BS ISO 8139:2009 ISO 8139:2009(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file m

6、ay be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat acc

7、epts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that t

8、he file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2009 All rights reserved. Unless otherwise specified, no part of this publication may be

9、reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41

10、 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2009 All rights reservedBS ISO 8139:2009 ISO 8139:2009(E) ISO 2009 All rights reserved iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of nation

11、al standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. Internatio

12、nal organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rule

13、s given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at l

14、east 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 8139 was prepared by Technical Committee ISO/TC 13

15、1, Fluid power systems, Subcommittee SC 3, Cylinders. This third edition cancels and replaces the second edition (ISO 8139:1991), which has been technically revised. BS ISO 8139:2009 ISO 8139:2009(E) iv ISO 2009 All rights reservedIntroduction In pneumatic fluid power systems, power is transmitted a

16、nd controlled through a gas under pressure within a circuit. One component of such systems is the pneumatic fluid power cylinder. This is a device that converts power into linear mechanical force and motion. It consists of a movable element, i.e. a piston and piston rod, operating within a cylindric

17、al bore. BS ISO 8139:2009 INTERNATIONAL STANDARD ISO 8139:2009(E) ISO 2009 All rights reserved 1 Pneumatic fluid power Cylinders, 1 000 kPa (10 bar) series Mounting dimensions of rod-end spherical eyes 1 Scope This International Standard specifies the mounting dimensions required for interchangeabil

18、ity of rod-end spherical eyes of pneumatic cylinders. The rod-end spherical eyes have been designed specifically for use with 1 000 kPa 10 bar 1) series cylinders manufactured in accordance with ISO 6430, ISO 6432 and ISO 15552, but this does not limit their application. The spherical bearing end ey

19、es are used on piston rods of pneumatic cylinders for mechanically transmitting the cylinder force under oscillatory rotational and tilting movements. The design of the rod-end spherical eyes is based on the maximum forces resulting from the specified internal diameter of the cylinders and pressure

20、according to ISO 6430, ISO 6432 and ISO 15552. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any

21、amendments) applies. ISO 5598, Fluid power systems and components Vocabulary ISO 6099, Fluid power systems and components Cylinders Identification code for mounting dimensions and mounting types ISO 6430, Pneumatic fluid power Single rod cylinders, 1 000 kPa (10 bar) series, with integral mountings,

22、 bores from 32 mm to 250 mm Mounting dimensions ISO 6432, Pneumatic fluid power Single rod cylinders 10 bar (1 000 kPa) series Bores from 8 to 25 mm Mounting dimensions ISO 15552, Pneumatic fluid power Cylinders with detachable mountings, 1 000 kPa (10 bar) series, bores from 32 mm to 320 mm Basic,

23、mounting and accessories dimensions 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 5598 apply. The identification code for mounting dimensions and mounting types is in accordance with ISO 6099. 1) 1 bar = 100 kPa = 10 5Pa; 1 Pa = 1 N/m 2 . BS ISO 81

24、39:2009 ISO 8139:2009(E) 2 ISO 2009 All rights reserved4 Mounting dimensions See Figure 1 and Table 1. Figure 1 AP6 Rod-end spherical eyes Table 1 Dimensions of AP6 Rod-end spherical eyes Dimensions in millimetres KK CN EN CH LF EF AV Tilting angle Z H9 h12 min. max. min. min. degree M4 0,7 5 8 27 1

25、0 9 10 M6 1 6 9 30 11 10 12 M8 1,25 8 12 36 13 12 16 M10 1,25 10 14 43 15 14 20 M12 1,25 12 16 50 17 16 22 M16 1,5 16 21 64 22 21 28 M20 1,5 20 25 77 26 25 33 M27 2 30 37 110 36 35 51 M36 2 35 43 125 41 40 56 M42 2 40 49 142 46 45 60 M48 2 50 60 160 59 58 65 4 BS ISO 8139:2009 ISO 8139:2009(E) ISO 2

26、009 All rights reserved 3 5 Application instructions 5.1 Installation 5.1.1 Usually a tolerance of m6 (see ISO 286-2) is used for the shaft fitting the spherical plain bearing bore. However, in exceptional cases (for example cylinder installation difficulties), a tolerance of f7 can be admitted. In

27、this instance, a case-hardened shaft is recommended as movement occurs between the shaft and the bearing bore. Lubrication shall then be effected through the shaft. 5.1.2 The specified tilting angle of 4 can still be obtained when the clevis inner faces abut the side faces of the inner ring of the s

28、pherical plain bearing. 5.1.3 The rod-end spherical eyes shall be locked with a locking nut. 5.2 Bearing life 5.2.1 The life of the spherical plain bearing is influenced by many factors such as specified load, direction of load, angle of oscillation, type of lubricant and frequency of lubrication. 5

29、.2.2 The spherical plain bearings are designed to give an acceptable bearing life under normal operating conditions. 5.2.3 Where a constant unidirectional load is applied or other unusual operating conditions exist, consultation with the supplier is recommended. 5.3 Lubrication 5.3.1 Sufficient lubr

30、ication shall be provided for the satisfactory performance of the rod-end spherical eyes. 5.3.2 The method and frequency of such lubrication depend on the particular operating conditions. 6 Example of ordering designation A rod-end spherical eye with a bore of CN = 20 mm and steel-on-steel surface s

31、hall be designated as follows: Rod eye spherical ISO 8139 20 7 Identification statement (reference to this International Standard) It is strongly recommended to manufacturers who have chosen to conform to this International Standard that the following statement be used in test reports, catalogues an

32、d sales literature: “Pneumatic cylinder rod-end spherical eye mounting dimensions in accordance with ISO 8139:2009, Pneumatic fluid power Cylinders, 1 000 kPa (10 bar) series Mounting dimensions of rod-end spherical eyes.” BS ISO 8139:2009 ISO 8139:2009(E) 4 ISO 2009 All rights reservedBibliography

33、1 ISO 286-2, ISO system of limits and fits Part 2: Tables of standard tolerance grades and limit deviations for holes and shafts BS ISO 8139:2009BS ISO 8139:2009 ISO 8139:2009(E) ICS 23.100.20 Price based on 4 pages ISO 2009 All rights reserved BS ISO 8139:2009 This page has been intentionally left

34、blankBS ISO 8139:2009 BSI Group Headquarters 389 Chiswick High Road, London, W4 4AL, UK Tel +44 (0)20 8996 9001 Fax +44 (0)20 8996 7001 standards BSI - British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standard

35、s in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of

36、our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 899

37、6 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20

38、8996 9001. Fax: +44 (0)20 8996 7001 Email: You may also buy directly using a debit/credit card from the BSI Shop on the Website http:/ In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless

39、otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its produ

40、cts and services. Contact Information Centre. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Mem

41、bership Administration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via British Standards Online can be found at http:/ Further information about BSI is available on the BSI website at http:/ Copyright Copyright subsists in all

42、BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means elec

43、tronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright and Licensing Manager. Tel: +44 (0)20 8996 7070 Email: