BS ISO 8277-2013 Ships and marine technology Pipework and machinery Information transfer《船舶与海洋技术 管道工程与机械 信息传递》.pdf

1、raising standards worldwide NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BSI Standards Publication BS ISO 8277:2013 Ships and marine technology Pipework and machinery Information transferBS ISO 8277:2013 BRITISH STANDARD National foreword This British Standard is the UK imp

2、lementation of ISO 8277:2013. The UK participation in its preparation was entrusted to Technical Committee SME/32/-/3, Ships and marine technology - Piping and machinery. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purp

3、ort to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2013. Published by BSI Standards Limited 2013 ISBN 978 0 580 78935 9 ICS 35.240.60; 47.020.30 Compliance with a British Standard cannot confer immunity from

4、 legal obligations. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 June 2013. Amendments issued since publication Date Text affectedBS ISO 8277:2013 ISO 2013 Ships and marine technology Pipework and machinery Information transfer Navires

5、et technologie maritime Tuyauteries et machines Transmission dinformations INTERNATIONAL STANDARD ISO 8277 Second edition 2013-06-01 Reference number ISO 8277:2013(E)BS ISO 8277:2013ISO 8277:2013(E)ii ISO 2013 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO 2013 All rights reserved. Unless othe

6、rwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address

7、below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in SwitzerlandBS ISO 8277:2013ISO 8277:2013(E) ISO 2013 All rights reserved iii Contents Pa

8、ge Foreword iv Introduction v 1 Scope . 1 2 Normative references 1 3 Pipework information 1 3.1 Information on standard parts 1 3.2 Information on non-standard parts 2 3.3 Administrative information . 4 4 Flow chart 6 Bibliography 8BS ISO 8277:2013ISO 8277:2013(E) Foreword ISO (the International Org

9、anization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been establi

10、shed has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardizatio

11、n. The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with

12、the editorial rules of the ISO/IEC Directives, Part 2. www.iso.org/directives Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent r

13、ights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received. www.iso.org/patents Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement. The committee

14、 responsible for this document is ISO/TC 8, Ships and marine technology, Subcommittee SC 3, Piping and machinery. This second edition cancels and replaces the first edition ( ISO 8277:1988), which has been technically revised.iv ISO 2013 All rights reservedBS ISO 8277:2013ISO 8277:2013(E) Introducti

15、on The revision to this International Standard takes into account the recent globalization of the shipbuilding industry and manufacturers of installed equipment, and the transformation of specifications, which introduce the following points into piping machinery at shipyards: A growing number of ins

16、talled equipment and piping equipment manufacturers, and their models; A diversification of standards specifying piping installations and piping fittings used by shipyards and/or ship equipment manufacturers. With this background there is a lack of information necessary to carry out pipe fittings an

17、d machinery in shipyards, and an absence of consistency in the descriptions of these points. This International Standard is revised taking into consideration the current situation of piping machinery in shipyards. In order to enable manufacturers of equipment and/or piping equipment to comply with t

18、his International Standard which specifies procedures of drawings and manufacturing, the revision covers the following points: The implementation of this International Standard for operation when applying other international standards and/or each national standard; The description of as many referen

19、ces as possible in a requirements and comments table as applicable requirements to the latest circumstances of pipe fitting in shipyards. ISO 2013 All rights reserved vBS ISO 8277:2013BS ISO 8277:2013Ships and marine technology Pipework and machinery Information transfer 1 Scope This International S

20、tandard specifies the minimum data needed for the prefabrication and assembly of pipework and for its transfer from engineering departments to workshops in the shipbuilding industry. It is applicable to written information needed for construction of piping installations that marine piping equipment

21、manufacturers submit through specifications and instructions to shipyards on shipbuilding. It is not applicable to the generation, type presentation and filing organization of this data. 2 Normative references The following referenced documents are indispensable for the application of this document.

22、 For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 14726:2008, Ships and marine technology Identification colours for the content of piping systems ISO 15583:2005, Ships and marine techn

23、ology Maritime standards list 3 Pipework information The type of pipework information shall be divided into three parts as follows: Information on standard parts (see 3.1); Information on non-standard parts (see 3.2); Administrative information (see 3.3). 3.1 Information on standard parts Table 1 In

24、formation on standard parts Item of pipework information Requirements and comments 3.1.1 Identification A special sequence of characters that could be part of, or include, one of the numbers given in 3.3. 3.1.2 Name, standard Each part shall be given a name and reference shall be made to internation

25、al, national or industry standards. Example of national standards: DIN, ANSI, JIS, BS, NF, KS, GB, etc. (see Table 4). These national standards are listed in ISO 15583:2005. 3.1.3 Pressure 3.1.3.1 Nominal pressure (PN) Table 4 shows the nominal pressures in national standards. INTERNATIONAL ST ANDAR

26、D ISO 8277:2013(E) ISO 2013 All rights reserved 1BS ISO 8277:2013ISO 8277:2013(E) Item of pipework information Requirements and comments 3.1.3.2 Test pressure Strength, tightness, procedure of pressure testing, where not defined by the relevant standard. 3.1.4 Nominal diameter (DN) Table 5 shows a c

27、omparison of the national standards nominal diameters. 3.1.5 Material Indication of material and thickness, and propriety of classifica- tion material. 3.1.6 Dimensions Of the finished product, relevant for assembly. Description for bolt circle position of flange, lining thickness, gasket thickness

28、and presence of lining. 3.1.7 Mass (net) 3.1.8 Location Global and local; the position of the part should be given in the ship or plant coordinate system, and in relative measures (optional). 3.1.8 Attachments included Description of parts necessary for the assembly, e.g. gaskets, bolts, supports, e

29、tc. 3.1.9 Identification colours Pipework identification colours in accordance with ISO 14726:2008 shall be used. Identification colour should be at the same time ensured to be in compliance with statutory requirements, rules and regula- tions. 3.1.10 Attachments included Description of parts necess

30、ary for the assembly, e.g. gaskets, bolts, supports, etc. 3.1.11 Certification or information on certification required Result of non-destructive inspection, manufacturers pressure test or onboard pressure test. 3.1.12 Other (General) Subclause 3.2 may be used as in 3.1 if necessary for information

31、on standard parts. 3.2 Information on non-standard parts Table 2 Information on non-standard parts Item of pipework information Recommendations and comments 3.2.1 Identification See 3.1. 3.2.2 Name, drawing number Each part shall be given a name and reference shall be made to the drawing which conta

32、ins the manufacturing informa- tion. 3.2.3 Pressure 3.2.3.1 Nominal pressure (PN)Table 1 (continued) 2 ISO 2013 All rights reservedBS ISO 8277:2013ISO 8277:2013(E) Item of pipework information Recommendations and comments 3.2.3.2 Test pressure Strength, tightness, and pressure testing procedure whic

33、h should follow an international, national or industry stand- ard. 3.2.4 Nominal diameter (DN) See 3.1.4. 3.2.5 Material See 3.1.5. 3.2.6 Semi-manufactured articles Name and dimensions prior to production. 3.2.7 Dimensions See 3.1.6. Description for the pipe end dimensions, e.g. outside diam- eter a

34、nd thickness. 3.2.8 Manufacturing information 3.2.8.1 For cutting Example: metal saw, press, thermal cutting such as gas, plasma, laser. 3.2.8.2 For flanging and hole orientation Example: flanges provided by regional standards such as ANSI, JIS,. KS, DIN, gasket material needed, etc. 3.2.8.3 For ben

35、ding, including sequence of bending and heat treatment 3.2.8.4 For welding, including joint preparation and heat treatment 3.2.8.5 For finishing Galvanizing, Phosphating, Pickling and oil coated, Synthetic rubber lining, Polyethylene lining, Pickling and V.P.I., Non-tar epoxy painting. 3.2.8.6 For t

36、esting 3.2.8.7 For preservation Treatment of outside surface. 3.2.8.8 For labellingTable 2 (continued) ISO 2013 All rights reserved 3BS ISO 8277:2013ISO 8277:2013(E) 3.3 Administrative information Table 3 Administrative information Item of pipework information Recommendations and comments 3.3.1 Syst

37、em number A sequence of alpha, numeric or alphanumeric characters. 3.3.2 Drawing number See 3.3.1. 3.3.3 Stock number See 3.3.1. 3.3.4 Ordering number See 3.3.1. 3.3.5 Part number See 3.3.1. 3.3.6 Number of pieces 3.3.7 Delivery date Table 4 Numeric nominal pressure of designation and marking listin

38、g PN-Nominal pressure series (DIN, NF, BS, GB) Class-Nominal pressure series (ANSI) K-Nominal pressure series (JIS, KS) PN 2,5 PN 6 PN 10 PN 16 PN 25 PN 40 PN 64 PN 100 Class 75 Class 125 Class 150 Class 250 Class 300 Class 400 Class 600 Class 900 Class 1500 Class 2500 Class 4500 2 K 5 K 10 K 16 K 2

39、0 K 30 K 40 K 63 KNOTE This table is not a comparison table. Nominal pressures shown in this table do not correspond to each other.4 ISO 2013 All rights reservedBS ISO 8277:2013ISO 8277:2013(E) Table 5 Numeric nominal diameter of designation and marking listing Nominal diameter for Designation and M

40、arking DN (DIN, NF, BS,GB) NPS (ANSI) A (JIS,KS) 10 15 20 * 1/2 3/4 10 15 20 25 32 40 1 11/4 11/2 25 32 40 50 65 80 2 21/2 3 50 65 80 * 100 125 31/2 4 5 90 100 125 150 * 200 6 * 8 150 175 200 * 250 300 * 10 12 225 250 300 350 400 450 14 16 18 350 400 450 500 * 600 20 * 24 500 550 600 * 700 * 26 28 3

41、0 650 700 750 800 * 900 32 34 36 800 850 900 * 1000 * 38 40 42 950 1000 1050NOTE This is a comparison table showing nominal diameters of the national standards. ISO 2013 All rights reserved 5BS ISO 8277:2013ISO 8277:2013(E) Nominal diameter for Designation and Marking DN (DIN, NF, BS,GB) NPS (ANSI)

42、A (JIS,KS) * * 1200 44 46 48 1100 1150 1200 * * * 50 52 54 1250 1300 1350 1400 * * 56 58 60 1400 1450 1500 1600 1800 2000 * * * * * * 2400 2600 2800 * * * * * * 3000 3200 3400 * * * * * * 3600 3800 4000 * * * * * *NOTE This is a comparison table showing nominal diameters of the national standards. 4

43、 Flow chart The data and material flow for pipe production and installation and the interface are shown in the flow chart (Figure 1).Table 5 (continued) 6 ISO 2013 All rights reservedBS ISO 8277:2013ISO 8277:2013(E) Figure 1 Data and material flow for pipe production and installation ISO 2013 All ri

44、ghts reserved 7BS ISO 8277:2013ISO 8277:2013(E) Bibliography 1 ISO 7005-1:2011, Pipe flanges Part 1: Steel flanges for industrial and general service piping systems 2 ISO 7460, Shipbuilding Shiplines Identification of geometric data 3 ANSI/ASME B16.5, Pipe flanges and flanged fittings 4 ANSI/ASME B1

45、6.47, Large Diameter Steel Flanges:NPS 26 through NPS 60 5 EN 19, Industrial valves Marking of metallic valves 6 EN 1092-1, Flanges and their joints Circular flanges for pipes, valves, fittings and accessories, PN designated Part1: Steel flanges 7 JIS B 2220, Steel pipe flanges 8 KS B 1503, Flange 9

46、 NF E 29-282, Plate flange for welding 10 GB/T 9112, Types and parameters for steel pipe flanges8 ISO 2013 All rights reservedBS ISO 8277:2013BS ISO 8277:2013ISO 8277:2013(E) ISO 2013 All rights reserved ICS 35.240.60;47.020.30 Price based on 8 pagesThis page deliberately left blankBSI is the indepe

47、ndent national body responsible for preparing British Standards and other standards-related publications, information and services. It presents the UK view on standards in Europe and at the international level. BSI is incorporated by Royal Charter. British Standards and other standardisation product

48、s are published by BSI Standards Limited. British Standards Institution (BSI) raising standards worldwide BSI 389 Chiswick High Road London W4 4AL UK Te l + 4 4 ( 0 ) 2 0 8 9 9 6 9 0 0 1 Fax +44 (0)20 8996 7001 Revisions British Standards and PASs are periodically updated by amendment or revision.

49、Users of British Standards and PASs should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using British Standards would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. S i m i l a r y f o