BS ISO 8405-2013 Tools for moulding Ejector sleeves with cylindrical head Basic series for general purposes《注塑工具 圆柱头推管 一般用途基本系列》.pdf

1、BSI Standards Publication BS ISO 8405:2013 Tools for moulding Ejector sleeves with cylindrical head Basic series for general purposesBS ISO 8405:2013 BRITISH STANDARD National foreword This British Standard is the UK implementation of ISO 8405:2013. It supersedes BS ISO 8405:1998 which is withdrawn.

2、 The UK participation in its preparation was entrusted to Technical Committee MTE/12, Tools for pressing and moulding. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a con

3、tract. Users are responsible for its correct application. The British Standards Institution 2013. Published by BSI Standards Limited 2013 ISBN 978 0 580 79404 9 ICS 25.120.30 Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published under t

4、he authority of the Standards Policy and Strategy Committee on 30 September 2013. Amendments issued since publication Date Text affectedBS ISO 8405:2013 ISO 2013 Tools for moulding Ejector sleeves with cylindrical head Basic series for general purposes Outillage de moulage jecteurs tubulaires tte cy

5、lindrique Srie de base pour usages gnraux INTERNATIONAL STANDARD ISO 8405 Third edition 2013-09-15 Reference number ISO 8405:2013(E)BS ISO 8405:2013ISO 8405:2013(E)ii ISO 2013 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO 2013 All rights reserved. Unless otherwise specified, no part of this p

6、ublication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the c

7、ountry of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in SwitzerlandBS ISO 8405:2013ISO 8405:2013(E) Foreword ISO (the International Organization for Standardization) is a worldwi

8、de federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on tha

9、t committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The procedures used to develop this docu

10、ment and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directiv

11、es, Part 2. www.iso.org/directives Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of

12、the document will be in the Introduction and/or on the ISO list of patent declarations received. www.iso.org/patents Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement. For an explanation on the meaning of ISO specific terms

13、and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: http:/ /www.iso.org/iso/home/standards_development/resources-for- technical-work/foreword.htm The committee responsible

14、for this document is ISO/TC 29, Small tools, Subcommittee SC 8, Tools for pressing and moulding. This third edition cancels and replaces the second edition (ISO 8405:1998), which has been technically revised. ISO 2013 All rights reserved iiiBS ISO 8405:2013BS ISO 8405:2013Tools for moulding Ejector

15、sleeves with cylindrical head Basic series for general purposes 1 Scope This International Standard specifies the dimensions and tolerances, in millimetres, of ejector sleeves with cylindrical head which are used in compression and injection moulds and in die casting dies. It also gives material gui

16、delines and hardness requirements, and specifies the designation of ejector sleeves with cylindrical head. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the editio

17、n cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 6751:2011, Tools for moulding Ejector pins with cylindrical head 3 Dimensions The dimensions of ejector sleeves with cylindrical head shall be in accordance with the indicat

18、ions of Figure 1 and Table 1. Surface roughness values in micrometres Key a Ra 0,8 for hot worked steel. Ra 0,4 for alloyed cold worked steel. b t = 0,012 mm (L 1 10 1 ). Figure 1 Ejector sleeves INTERNATIONAL ST ANDARD ISO 8405:2013(E) ISO 2013 All rights reserved 1BS ISO 8405:2013ISO 8405:2013(E)

19、Table 1 Ejector sleeves Dimensions in millimetres D 1 aH5 D 2g6 D 3 D 4- L 1 + L + H b- R + 75 100 125 150 175 200 225 250 275 300 2 4 2,5 8 35 X X X 3 0,3 2,5 5 3 10 X X X 3 3,5 45 X X X X 4 8 4,5 14 X X X X X X 5 0,5 5 5,5 X X X X X X 6 10 6,5 16 X X X X X X X 8 12 8,5 20 X X X X X X X X X 7 0,8 1

20、0 14 10,5 22 X X X X X X X X X 12 16 12,5 X X X X X X X X aFor repair, the following diameters are recommended: 2,2; 2,7; 3,2; 4,2; 5,2; 6,2; 8,2; 10,2; 12,5 (for D 1= 12,5, D 3= 13). bFor shaft diameters, D 2 , larger than those given in Table 1, up to 32 mm, the ratio of head height and diameter s

21、hall be the same as for ejector pins given in ISO 6751. 4 Material and hardness Ejector sleeves with cylindrical head shall be made of hot worked steel or alloyed cold worked steel. The hardness of the shaft and head, respectively, are given in Table 2. Table 2 Material and hardness Material Hardnes

22、s a Shaft Head Hot worked steel min. 1 400 MPa core strength min. 950 HV 0,3 (45 5) HRC hot- forged Alloyed cold worked steel (60 2) HRC aThe point at which hardness is measured is left to the manufacturers discretion.2 ISO 2013 All rights reservedBS ISO 8405:2013ISO 8405:2013(E) 5 Designation Eject

23、or sleeves with cylindrical head according to this International Standard shall be designated by the following: a) “Ejector sleeve with cylindrical head”; b) a reference to this International Standard (i.e. ISO 8405:2013); c) the diameter, D 1 , in millimetres; d) the length, L, in millimetres; e) t

24、he material. EXAMPLE An ejector sleeve with cylindrical head with diameter D 1= 2 mm, length L = 75 mm, and made of hot worked steel is designated as follows: Ejector sleeve with cylindrical head ISO 8405 - 2 - 75 - Hot worked steel ISO 2013 All rights reserved 3BS ISO 8405:2013ISO 8405:2013(E) ISO

25、2013 All rights reserved IC S 25.120.30 Price based on 3 pagesThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services. BSI is incorporated by Royal Charter. British Standards and other st

26、andardization products are published by BSI Standards Limited. British Standards Institution (BSI) BSI Group Headquarters 389 Chiswick High Road London W4 4AL UK About us We bring together business, industry, government, consumers, innovators and others to shape their combined experience and experti

27、se into standards -based solutions. The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals. Information on stand

28、ards We can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre. Buying standards You can buy and download PDF versions of BSI publications, including Br

29、itish and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team. Subscriptions Our range

30、 of subscription services are designed to make using standards easier for you. For further information on our subscription products go to With British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its ava

31、ilable 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exc

32、lusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit With a Multi-User Network Licence (MUNL) you are able to ho

33、st standards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is current. For further information, email . Revisions Our British Standards and other publications are updated by

34、 amendment or revision. We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre. Copyright All the data, software and documentation set out i

35、n all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use.

36、 Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. Details and advice can be obtained

37、from the Copyright & Licensing Department. Useful Contacts: Customer Services Tel: +44 845 086 9001 Email (orders): Email (enquiries): Subscriptions Tel: +44 845 086 9001 Email: Knowledge Centre Tel: +44 20 8996 7004 Email: Copyright & Licensing Tel: +44 20 8996 7070 Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW