BS ISO 8528-6-2006 Reciprocating internal combustion engine driven alternating current generating sets - Test methods《往复式内燃机驱动的交流发电装置 试验方法》.pdf

1、BRITISH STANDARD BS ISO 8528-6:2005 Reciprocating internal combustion engine driven alternating current generating sets Part 6: Test methodsICS 27.020; 29.160.40 BS ISO 8528-6:2005 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 3 February 20

2、06 BSI 3 February 2006 ISBN 0 580 47709 6 National foreword This British Standard reproduces verbatim ISO 8528-6:2005 and implements it as the UK national standard. It supersedes BS 7698-6:1993 which is withdrawn. The UK participation in its preparation was entrusted by Technical Committee MCE/14, R

3、IC engines, to Subcommittee MCE/14/-/8, RIC engines generating sets, which has the responsibility to: A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement international publications referred to in

4、 this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a

5、 contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or propos

6、als for change, and keep UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the ISO title page, pages ii to iv, pages 1 to 13 and a back cover. The BSI copyright

7、notice displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date Comments Reference number ISO 8528-6:2005(E)INTERNATIONAL STANDARD ISO 8528-6 Second edition 2005-06-01 Reciprocating internal combustion engine driven alternating current

8、 generating sets Part 6: Test methods Groupes lectrognes courant alternatif entrans par moteurs alternatifs combustion interne Partie 6: Mthodes dessai BS ISO 8528-6:2005ii iiiContents Page Foreword iv 1 Scope 1 2 Normative references . 1 3 Other regulations and additional requirements. 2 4 General

9、test requirements 2 5 ISO standard functional test 2 5.1 General. 2 5.2 General inspection 3 5.3 Measurements . 3 5.4 Measurement equipment accuracy . 3 5.5 ISO standard functional test report. 4 6 Acceptance test. 5 6.1 General. 5 6.2 Contractual arrangements . 5 6.3 Responsibility 5 6.4 Preparatio

10、n 6 6.5 Further details . 6 6.6 Extent of acceptance test. 7 6.7 Accuracy of measurement equipment and acceptance test procedure . 9 6.8 Acceptance test report . 11 BS ISO 8528-6:2005iv Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards

11、bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizat

12、ions, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in th

13、e ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of

14、the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 8528-6 was prepared by Technical Committee ISO/TC 70, Internal

15、combustion engines. This second edition cancels and replaces the first edition (ISO 8528-6:1993), which has been technically revised. ISO 8528 consists of the following parts, under the general title Reciprocating internal combustion engine driven alternating current generating sets: Part 1: Applica

16、tion, ratings and performance Part 2: Engines Part 3: Alternating current generators for generating sets Part 4: Controlgear and switchgear Part 5: Generating sets Part 6: Test methods Part 7: Technical declarations for specification and design Part 8: Requirements and tests for low-power generating

17、 sets Part 9: Measurement and evaluation of mechanical vibrations Part 10: Measurement of airborne noise by the enveloping surface method Part 11: Rotary uninterruptible power systems Performance requirements and test methods 1) Part 12: Emergency power supplies to safety services 1) Part 11 will be

18、 published as ISO/IEC 88528-11. BS ISO 8528-6:2005 1Reciprocating internal combustion engine driven alternating current generating sets Part 6: Test methods 1 Scope This part of ISO 8528 specifies the test methods to be used for characterizing an entire generating set. It applies to alternating curr

19、ent (a.c.) generating sets driven by reciprocating internal combustion (RIC) engines for land and marine use, excluding generating sets used on aircraft or to propel land vehicles and locomotives. For some specific applications (e.g. essential hospital supplies, high-rise buildings) supplementary re

20、quirements may be necessary. The provisions of this part of ISO 8528 are intended as a basis for establishing any supplementary requirements. For a.c. generating sets driven by other reciprocating type prime movers (e.g. steam engines), this part of ISO 8528 is intended as a basis for establishing t

21、hese requirements. NOTE Existing test methods for the engine (ISO 3046-1 and ISO 3046-3) and generator (IEC 60034-2) are applicable for those components. The generating set manufacturer is responsible for specifying these characteristics and the tests to be performed to verify them. 2 Normative refe

22、rences The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 3046-1, Reciprocal internal combustion

23、 engines Performance Part 1: Declarations of power, fuel and lubricating oil consumptions, and test methods Additional requirements for engines for general use ISO 3046-3, Reciprocating internal combustion engines Performance Part 3: Test measurements ISO 8528-1 2) , Reciprocating internal combustio

24、n engine driven alternating current generating sets Part 1: Application, ratings and performance ISO 8528-5 2) , Reciprocating internal combustion engine driven alternating current generating sets Part 5: Generating sets IEC 60034-2, Rotating electrical machines Part 2: Methods for determining losse

25、s and efficiency of rotating electrical machinery from tests (excluding machines for traction vehicles) IEC 60034-5, Rotating electrical machines Part 5: Classification of degrees of protection provided by enclosures for rotating machines IEC 60947-1, Low-voltage switchgear and control gear Part 1:

26、General rules 2) ISO 8528-1 and ISO 8528-5 are under revision. BS ISO 8528-6:20052 3 Other regulations and additional requirements For a.c. generating sets used on board ships and offshore installations which have to comply with rules of a classification society, the additional requirements of the c

27、lassification society shall be observed. The classification society name shall be stated by the customer prior to placing the order. For a.c. generating sets operating in non-classified equipment, any additional requirements are subject to agreement between the manufacturer and customer. If special

28、requirements from regulations of any other authority (e.g. inspecting and/or legislative authorities) have to be met, the authority name shall be stated by the customer prior to placing the order. Any additional requirements shall be subject to agreement between the manufacturer and customer. 4 Gene

29、ral test requirements Generating sets shall be tested in accordance with either the ISO standard functional test (see Clause 5) or the ISO standard acceptance test (see Clause 6). Subject to agreement between the generating set manufacturer and customer, any or all of the functional tests may be com

30、bined with the acceptance test. The acceptance test shall be carried out at the manufacturers works and/or installation site. The type of test to be performed shall be agreed in writing between the manufacturer and customer. Detailed requirements for the generating set acceptance tests depend on the

31、 following principal areas: a) its application; b) its power output; c) the extent of supply; d) its use; e) its performance class according to ISO 8528-1 and ISO 8528-5. As a minimum, the generating set manufacturer test shall perform the ISO standard functional test in accordance with the correct

32、rating and performance class of the generating set. A test report shall be prepared in accordance with the requirements of 5.5. The ISO standard functional test procedure is intended for use with the generating set installed on the manufacturers test bed. Subject to agreement between the manufacture

33、r and customer, the functional and/or acceptance test may be performed at the customers site or at a third party location. 5 ISO standard functional test 5.1 General This functional test shall be performed on the generating set with it at the manufacturers works under test-bed conditions. The rated

34、power factor load is normally used for testing, with due regard paid to the rated active power and associated generator efficiency. Optionally, if this is not possible because of the test equipment used, this test may be performed at a power factor of unity. This shall be by agreement between the ma

35、nufacturer and customer. BS ISO 8528-6:2005 35.2 General inspection A general inspection in order to establish compliance with specifications in accordance with the generator set manufacturers instructions shall be carried out which shall cover (as a minimum): a) completeness of the item supplied an

36、d to be tested; b) alignment; c) functional operations of the auxiliary equipment supplied (by agreement); d) tightness of pipework joints and components; e) degree of protection as described in IEC 60034-5 and IEC 60947-1; f) operating and monitoring functions. NOTE When measuring non-precision par

37、ts, such as a fan guard, a statistical approach to protection prediction is acceptable. 5.3 Measurements The test shall be performed on generating sets that have reached their nominal operating temperature. The time required to warm up the generating set will vary. It is the responsibility of the te

38、st engineer to ensure that the set has run for an adequate time in order to stabilize temperatures. The following data shall be recorded (as a minimum): a) ambient temperature, humidity and barometric pressure; b) generating set voltage, current and frequency at rated output; c) generating set volta

39、ge, frequency and current while loading and unloading to assess transient behaviour; d) the proper functioning of any monitoring and control equipment. 5.4 Measurement equipment accuracy The minimum accuracy of the instrumentation used in the test shall be as shown in Table 1. Measuring transformers

40、 and transducers should be of a corresponding accuracy class. Table 1 ISO standard acceptance test Measurement equipment accuracy Parameter Unit Accuracy (%) Current A 1,5 Voltage V 1,5 Real power W 1,5 Reactive power kVA 1,5 Power factor 3,0 Frequency Hz 0,5 BS ISO 8528-6:20054 5.5 ISO standard fun

41、ctional test report The ISO standard functional test report shall include the following information (as a minimum): a) the generating set performance class in accordance with the requirements of ISO 8528-1; b) the customer and order number (if known); c) the manufacturer; d) the engine, generator, c

42、ontrolgear and switchgear serial numbers; e) technical data, both declared (rated) and measured, as follows: 1) power; 2) voltage; 3) frequency; 4) current; 5) power factor; 6) speed; 7) circuit diagram number; 8) type of cooling system. f) enclosure protection; g) test site ambient conditions: 1) a

43、ltitude; 2) barometric pressure; 3) temperature; 4) relative humidity; 5) inlet air temperature; 6) inlet coolant temperature. h) fuel type (specification number): 1) density; 2) calorific value (lower calorific value). i) lubricating oil type (specification number). BS ISO 8528-6:2005 56 Acceptance

44、 test 6.1 General ISO 8528-1 to ISO 8528-5 specify requirements for various generating set applications. The manufacturer shall certify that the generating set complies with the requirements given in ISO 8528-2 to ISO 8528-5, unless compliance is established by using the acceptance test in accordanc

45、e with this part of ISO 8528. In particular, this applies to claiming compliance with the contractually agreed performance classes defined in ISO 8528-1 and ISO 8528-5, as well as to agreed requirements or variations in the performance classification for specific operating limits. 6.2 Contractual ar

46、rangements The details of an acceptance test performed in accordance with the requirements of this part of ISO 8528 shall be agreed in writing between the manufacturer and customer at the time of purchase. The test equipment used shall be such that the measurements and checks agreed for the acceptan

47、ce test can be verified within the agreed accuracy limits. The validation of further requirements, the performance of additional measurements or the provision of further tests which go beyond the requirements of 6.6 shall be agreed in writing between the manufacturer and customer before any tests ar

48、e performed. If the requirements of the tests specified in Clause 6 are changed during the acceptance test, an appropriate agreement shall be made. The cost of a complete or partial repetition or extension of the agreed acceptance test programme shall be borne by the party responsible for the repeti

49、tion or extension. The acceptance test shall be performed within the agreed period following notification of readiness for the test to start. The manufacturer of the generating set shall not be responsible for servicing any equipment provided by the customer. By agreement between the manufacturer and the customer, the works test of the complete generating set with test certificates may be considered as substitutes for the