BS ISO 8574-2008 Aerospace Hydraulic system tubing Qualification tests for bent tubes《航空航天 液压系统管路安装 弯曲管道的合格试验》.pdf

1、BRITISH STANDARD BS ISO 8574:2004 Aerospace Hydraulic system tubing Qualification tests for bent tubes ICS 49.080 BS ISO 8574:2004 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 March 2008 BSI 2008 ISBN 978 0 580 61242 8 National foreword

2、 This British Standard is the UK implementation of ISO 8574:2004. The UK participation in its preparation was entrusted to Technical Committee ACE/69, Aerospace hydraulic systems, fluids and components. A list of organizations represented on this committee can be obtained on request to its secretary

3、. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations. Amendments/corrigenda issued since publication Date CommentsINTERNATIONAL ST

4、ANDARD ISO 8574 Second edition 2004-05-01 Reference number ISO 8574:2004(E) Aerospace Hydraulic system tubing Qualification tests for bent tubes Aronautique et espace Tubes pour circuits hydrauliques Essais de qualification pour tubes coudsBS ISO 8574:2004ii iii Foreword ISO (the International Organ

5、ization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been establish

6、ed has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.

7、 International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Pu

8、blication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such paten

9、t rights. ISO 8574 was prepared by Technical Committee ISO/TC 20, Aircraft and space vehicles, Subcommittee SC 10, Aerospace fluid systems and components. This second edition cancels and replaces the first edition (ISO 8574:1990), which constitutes a minor revision by adding inch-dimensioned tubing

10、and by deleting flexure fatigue testing. BS ISO 8574:2004 blank1 Aerospace Hydraulic system tubing Qualification tests for bent tubes 1S c o p e This International Standard specifies pressure impulse and burst test procedures for determining and classifying the impulse fatigue strengths of bent tube

11、s used in aerospace hydraulic systems. The procedures are intended for qualification purposes of high- and low-pressure system tubing or for the evaluation of new materials for hydraulic system tubing. NOTE Requirements for tubing used in aerospace hydraulic systems are given in ISO 8575. 2 Normativ

12、e references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 6772, Aerospace Fluid systems Im

13、pulse testing of hydraulic hose, tubing and fitting assemblies 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 proof pressure static pressure for testing hydraulic system tubing, a prescribed multiple of the nominal system or sub-system press

14、ure 3.2 tube failure leakage or rupture of the tube itself during test NOTE See 6.1.2. 4 Test equipment 4.1 Pressure impulse equipment The test equipment shall be capable of producing the pressure impulse curve specified in ISO 6772 (see 6.3). 4.2 Burst pressure equipment The test equipment shall be

15、 capable of producing the pressure requirements specified in 6.4. BS ISO 8574:20042 5 Test specimens 5.1 Configuration The test specimens shall consist of bent lengths of the relevant tubing of dimensions as specified in Figure 1 and Table 1 (with inch-dimensioned tubing given in Table 2), according

16、 to the case, manufactured using production techniques and requirements, in addition to test fittings and adaptors where required. Except where otherwise specified, the bend radius ( ) of the specimens shall be three times the nominal tube diameter. anominal tubing diameter. Figure 1 Test specimen (

17、S-tube) for the impulse test Table 1 Test specimen lengths for impulse testing metric-size tubing (see Figure 1) Dimensions in millimetres Nominal tube size Total tube length DN size adesignation Nominal diameter DN6 6 65 30 300 DN10 10 65 30 300 DN12 12 90 30 400 DN16 16 140 30 510 DN20 20 140 30 5

18、70 DN25 25 140 30 670 a DN size is the nominal diameter expressed in millimetres. R R= 3 L 1 L 2 +13 0 +6 0 +25 0 BS ISO 8574:20043 5.2 Pre-test checks 5.2.1 The outside diameter and wall thickness of the tubing shall be measured and recorded, together with the ovality of the bend. 5.2.2 Three strai

19、ght samples of the test tubing shall also be checked to determine the basic material properties, i.e. yield tensile strength ( proof strength), ultimate tensile strength and elongation. 6T e s t i n g 6.1 General 6.1.1 Temperature Unless otherwise specified e.g. when testing to ISO 6772 (see 6.3), t

20、esting shall be carried out at ambient temperature unless the fatigue characteristics of the material in question are significantly affected by the extreme temperature limit envisaged. In this case, the temperature spectrum shall be as defined by the particular aerospace requirements. 6.1.2 Fitting

21、failures Failure of a tube fitting or at the fitting sleeve interface shall not constitute a tube failure. In the event of a failure during testing of a tube fitting or at the fitting sleeve interface, the fitting(s) shall be replaced and the tests continued, or a new tube specimen shall be tested.

22、6.2 Proof pressure test Prior to commencement of testing, all specimen tube assemblies shall be subjected to a proof pressure which, unless otherwise specified, shall be twice the system nominal operating pressure. 6.3 Pressure impulse test A minimum of six specimens for each size required to be tes

23、ted, mounted as specified in Figure 1 and Table 1, shall be subjected to pressure impulsing in accordance with ISO 6772. Table 2 Alternate test specimen lengths for impulse testing inch-size tubing (see Figure 1) Dimensions in inches Tube size Total tube length Dash size adesignation Nominal diamete

24、r 0,25 2,5 1,25 12 0,375 2,5 1,25 12 0,5 3,5 1,25 16 0,625 5,5 1,25 20 0,75 5,5 1,25 22 1 5,5 1,25 26 a Dash size is the nominal diameter expressed in 1/16 inch. L 1 L 2 +0,5 0 +0,25 0 +1 0 0,4 0,6 0,8 10 12 16 0,2 % BS ISO 8574:20044 6.4 Burst test At least two specimens of each size required to be

25、 tested, mounted as specified in Figure 1, shall be subjected to hydraulic pressure. The pressure shall be increased at a rate of until the tube bursts. Expansion of the tube before burst is permissible. 6.5 Dimensional check On completion of pressure impulse and burst tests, the specimens shall be

26、sectioned and the wall thickness around the bend(s) checked. 7 Requirements 7.1 Pressure impulse test The required use is dependent on the life of the aerospace vehicle, but as a minimum requirement the results shall demonstrate a life of 200 000 cycles when the specimens are subjected to maximum im

27、pulse pressures as specified for the system. 7.2 Burst test As a minimum requirement, each tube shall withstand, without failure, a burst pressure related to the system operating pressure in addition to any safety factor required for the particular application. (150 000 37 500) kPa/min (20 000 5 000

28、) psi/min BS ISO 8574:20045 Bibliography 1 ISO 8575, Aerospace Fluid systems Hydraulic system tubing BS ISO 8574:2004BS ISO 8574:2004 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presen

29、ts the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI

30、to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 899

31、6 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer

32、 Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Sta

33、ndards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details o

34、n all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these

35、and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-. Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- Further information about BSI is available on the BSI

36、website at http:/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a r

37、etrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.