BS ISO 8902-2009 Oil of lavandin Grosso (Lavandula angustifolia Mill x Lavandula latifolia Medik ) French type《法国杂薰衣草油(薰衣草 x阔叶薰衣草属)》.pdf

1、BS ISO 8902:2009 ICS 71.100.60 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BRITISH STANDARD Oil of lavandin Grosso (Lavandula angustifolia Mill. x Lavandula latifolia Medik.), French typeThis British Standard was published under the authority of the Standards Policy and St

2、rategy Committee on 30 November 2009 BSI 2009 ISBN 978 0 580 59402 1 Amendments/corrigenda issued since publication Date Comments BS ISO 8902:2009 National foreword This British Standard is the UK implementation of ISO 8902:2009. The UK participation in its preparation was entrusted to Technical Com

3、mittee AW/54, Essential oils. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Stand

4、ard cannot confer immunity from legal obligations.BS ISO 8902:2009Reference number ISO 8902:2009(E) ISO 2009INTERNATIONAL STANDARD ISO 8902 Third edition 2009-04-01 Oil of lavandin Grosso (Lavandula angustifolia Mill. Lavandula latifolia Medik.), French type Huile essentielle de lavandin Grosso (Lav

5、andula angustifolia Mill. Lavandula latifolia Medik.), type France BS ISO 8902:2009 ISO 8902:2009(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embe

6、dded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated.

7、 Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a prob

8、lem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2009 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, inclu

9、ding photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Publish

10、ed in Switzerland ii ISO 2009 All rights reservedBS ISO 8902:2009 ISO 8902:2009(E) ISO 2009 All rights reserved iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standa

11、rds is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also tak

12、e part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is

13、 to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibilit

14、y that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 8902 was prepared by Technical Committee ISO/TC 54, Essential oils. This third edition cancels and replaces the second edition (ISO 8

15、902:1999), which has been technically revised. BS ISO 8902:2009BS ISO 8902:2009 INTERNATIONAL STANDARD ISO 8902:2009(E) ISO 2009 All rights reserved 1 Oil of lavandin Grosso (Lavandula angustifolia Mill. Lavandula latifolia Medik.), French type 1 Scope This International Standard specifies certain c

16、haracteristics of the essential oil of lavandin Grosso Lavandula angustifolia Mill. Lavandula latifolia Medik., French type, intended for facilitating the assessment of its quality. 2 Normative references The following referenced documents are indispensable for the application of this document. For

17、dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO/TR 210, Essential oils General rules for packaging, conditioning and storage ISO/TR 211, Essential oils General rules for labelling and mark

18、ing of containers ISO 212, Essential oils Sampling ISO 279, Essential oils Determination of relative density at 20 C Reference method ISO 280, Essential oils Determination of refractive index ISO 592, Essential oils Determination of optical rotation ISO 875, Essential oils Evaluation of miscibility

19、in ethanol ISO 1242, Essential oils Determination of acid value ISO 11024-1, Essential oils General guidance on chromatographic profiles Part 1: Preparation of chromatographic profiles for presentation in standards ISO 11024-2, Essential oils General guidance on chromatographic profiles Part 2: Util

20、ization of chromatographic profiles of samples of essential oils 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 essential oil of lavandin Grosso essential oil obtained by steam distillation of the recently cut flowering tops of a specific cl

21、one known as the “Grosso” type of lavandin Lavandula angustifolia Mill. Lavandula latifolia Medik., of the Lamiaceae family, cultivated mainly in the south of France NOTE For information on the CAS number, see ISO/TR 210922 . BS ISO 8902:2009 ISO 8902:2009(E) 2 ISO 2009 All rights reserved4 Requirem

22、ents 4.1 Appearance Clear mobile liquid. 4.2 Colour Light yellow. 4.3 Odour Characteristic, slightly camphoraceous, lavender-like. 4.4 Relative density at 20 C, 20 20 d Minimum: 0,891 Maximum: 0,899 4.5 Refractive index at 20 C Minimum: 1,458 Maximum: 1,462 4.6 Optical rotation at 20 C Between 7 and

23、 3. 4.7 Miscibility in 70 % (volume fraction) ethanol at 20 C It shall not be necessary to use more than 3 volumes of 70 % (volume fraction) ethanol in order to obtain a clear solution with 1 volume of essential oil. 4.8 Acid value Maximum 1. 4.9 Chromatographic profile Carry out the analysis of the

24、 essential oil by gas chromatography. Identify in the chromatogram obtained the representative and characteristic components listed in Table 1. The percentage of each of these components, indicated by the integrator, shall lie within the limits given in Table 1. This constitutes the chromatographic

25、profile of the essential oil. BS ISO 8902:2009 ISO 8902:2009(E) ISO 2009 All rights reserved 3 Table 1 Chromatographic profile Component Minimum % Maximum % Myrcene 0,3 1,0 Limonene 0,5 1,5 1,8-Cineole 4,0 8,0 cis- -Ocimene 0,5 1,5 trans- -Ocimene not detectable 1,0 Linalool 24 37 Camphor 6,0 8,5 Bo

26、rneol 1,5 3,5 Lavandulol 0,2 1,0 Terpinen-4-ol 1,5 5,0 -Terpineol 0,3 1,3 Hexyl butyrate 0,3 0,5 Linalyl acetate 25 38 Lavandulyl acetate 1,5 3,5 NOTE The chromatographic profile is normative, contrary to the typical chromatograms given for information in Annex A. 4.10 Flashpoint Information concern

27、ing the flashpoint is given in Annex B. 5 Sampling See ISO 212. Minimum volume of test sample: 25 ml. NOTE This volume allows each of the tests specified in this International Standard to be carried out at least once. 6 Test methods 6.1 Relative density at 20 C, 20 20 d See ISO 279. 6.2 Refractive i

28、ndex at 20 C See ISO 280. 6.3 Optical rotation at 20 C See ISO 592. BS ISO 8902:2009 ISO 8902:2009(E) 4 ISO 2009 All rights reserved6.4 Miscibility in 70 % (volume fraction) ethanol at 20 C See ISO 875. 6.5 Acid value See ISO 1242. 6.6 Chromatographic profile See ISO 11024-1 and ISO 11024-2. 7 Packa

29、ging, labelling, marking and storage See ISO/TR 210 and ISO/TR 211. BS ISO 8902:2009 ISO 8902:2009(E) ISO 2009 All rights reserved 5 Annex A (informative) Typical chromatograms of the analysis by gas chromatography of the essential oil of lavandin Grosso (Lavandula angustifolia Mill. Lavandula latif

30、olia Medik.), French type Figure A.1 Typical chromatogram taken on an apolar column Peak identification Operating conditions 1 cis-3-Hexenol 2 Myrcene 3 Limonene 4 1,8-Cineole 5 cis- -Ocimene 6 trans- -Ocimene 7 Linalool 8 Camphor 9 Borneol 10 Lavandulol 11 Terpinen-4-ol 12 -Terpineol 13 Hexyl butyr

31、ate 14 Linalyl acetate 15 Lavandulyl acetate Column: silica capillary; length 50 m; internal diameter 0,20 mm Stationary phase: polydimethylsiloxane Film thickness: 0,25 m Oven temperature: programmed from 65 C to 230 C at a rate of 2 C/min Injector temperature: 230 C Detector temperature: 250 C Det

32、ector: flame ionization type Carrier gas: hydrogen Volume injected: 0,2 l Split ratio: 1/100 BS ISO 8902:2009 ISO 8902:2009(E) 6 ISO 2009 All rights reservedFigure A.2 Typical chromatogram taken on a polar column Peak identification Operating conditions 1 Myrcene 2 Limonene 3 1,8-Cineole 4 cis- -Oci

33、mene 5 trans- -Ocimene 6 cis-3-Hexenol coeluted 7 Hexyl butyrate 8 Camphor 9 Linalool 10 Linalyl acetate 11 Terpinen-4-ol 12 Lavandulyl acetate 13 Lavandulol 14 -Terpineol + borneol Column: silica capillary; length 50 m; internal diameter 0,20 mm Stationary phase: polyethylene glycol Film thickness:

34、 0,25 m Oven temperature: programmed from 65 C to 230 C at a rate of 2 C/min Injector temperature: 230 C Detector temperature: 250 C Detector: flame ionization type Carrier gas: hydrogen Volume injected: 0,2 l Split ratio: 1/100 BS ISO 8902:2009 ISO 8902:2009(E) ISO 2009 All rights reserved 7 Annex

35、B (informative) Flashpoint B.1 General information For safety reasons, transport companies, insurance companies and people in charge of safety services require information on the flash points of essential oils, which in most cases are flammable products. A comparative study on the relevant methods o

36、f analysis (see ISO/TR 11018 1 ) concluded that it was difficult to recommend a single apparatus for standardization purposes, given that: there is a wide variation in the chemical composition of essential oils; the volume of the sample needed for certain equipment is incompatible with the high pric

37、e of essential oils; as there are several different types of equipment which can be used for the determination, users cannot be expected to use one specified type only. Consequently, it was decided to give a mean value for the flashpoint annexed to each International Standard, for information, in or

38、der to meet the requirements of the interested parties. The equipment with which this value was obtained has to be specified. For further information, see ISO/TR 110181 . B.2 Flashpoint of the essential oil of lavandin Grosso (Lavandula angustifolia Mill. Lavandula latifolia Medik.), French type The

39、 indicative value is + 75 C (see Note 1) or + 78 C (see Note 2). NOTE 1 Value obtained with a Setaflash 1)appliance. NOTE 2 Value obtained with a Luchaire 1)appliance. 1) Equipment available commercially. This information is given for the convenience of users of this International Standard and does

40、not constitute an endorsement by ISO of these products. BS ISO 8902:2009 ISO 8902:2009(E) 8 ISO 2009 All rights reservedBibliography 1 ISO/TR 11018:1997, Essential oils General guidance on the determination of flashpoint 2 ISO/TR 21092, Essential oils Characterization BS ISO 8902:2009BS ISO 8902:200

41、9 ISO 8902:2009(E) ICS 71.100.60 Price based on 8 pages ISO 2009 All rights reserved BS ISO 8902:2009 This page has been intentionally left blankBS ISO 8902:2009 BSI Group Headquarters 389 Chiswick High Road, London, W4 4AL, UK Tel +44 (0)20 8996 9001 Fax +44 (0)20 8996 7001 standards BSI - British

42、 Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of Brit

43、ish Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the

44、 technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buy

45、ing standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001 Email: You may also buy directly using a debit/credit card from the BSI Shop on the Website http:/ In response to orders fo

46、r international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and

47、 its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact Information Centre. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: Subscribing members of BSI are kept up to date with stan

48、dards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via British Standards Online can be found at http:/ Further information about BSI is available on the BSI website at http:/ Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copy