BS ISO 9182-1-2013 Tools for pressing Guide pillars Types《冲压工具 导柱 类型》.pdf

1、BSI Standards Publication BS ISO 9182-1:2013 Tools for pressing Guide pillars Part 1: TypesBS ISO 9182-1:2013 BRITISH STANDARD National foreword This British Standard is the UK implementation of ISO 9182-1:2013. It supersedes BS 7568-25:1993 which is withdrawn. The UK participation in its preparatio

2、n was entrusted to Technical Committee MTE/12, Tools for pressing and moulding. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its co

3、rrect application. The British Standards Institution 2013. Published by BSI Standards Limited 2013 ISBN 978 0 580 76974 0 ICS 25.060.10; 25.120.10 Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the authority of the Standard

4、s Policy and Strategy Committee on 31 December 2013. Amendments issued since publication Date T e x t a f f e c t e dBS ISO 9182-1:2013 ISO 2013 Tools for pressing Guide pillars Part 1: Types Outillage de presse Colonnes de guidage Partie 1: Types INTERNATIONAL STANDARD ISO 9182-1 Second edition 201

5、3-12-15 Reference number ISO 9182-1:2013(E)BS ISO 9182-1:2013ISO 9182-1:2013(E)ii ISO 2013 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO 2013 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, elect

6、ronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel.

7、+ 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in SwitzerlandBS ISO 9182-1:2013ISO 9182-1:2013(E) ISO 2013 All rights reserved iii Contents Page Foreword iv 1 Scope . 1 2 Types, methods of mounting, and dimensions . 1BS ISO 9182-1:2013ISO 9182-1:2013(E) For

8、eword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a tech

9、nical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of

10、 electrotechnical standardization. The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document

11、 was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such

12、patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any trade name used in this document is information given for the convenience of users and does

13、not constitute an endorsement. For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary informat

14、ion The committee responsible for this document is ISO/TC 29, Small tools, Subcommittee SC 8, Tools for pressing and moulding. This second edition results from the reinstatement of ISO 9182-1:1992 which was withdrawn in 2007 and with which it is technically identical. ISO 9182 consists of the follow

15、ing parts, under the general title Tools for pressing Guide pillars: Part 1: Types Part 2: Type A, straight pillars Part 3: Type B, end-locking pillars Part 4: Type C, pillars with taper lead and bush Part 5: Type D, end-locking pillars with flangeiv ISO 2013 All rights reservedBS ISO 9182-1:2013INT

16、ERNATIONAL ST ANDARD ISO 9182-1:2013(E) Tools for pressing Guide pillars Part 1: Types 1 Scope This part of ISO 9182 illustrates four main types of guide pillars and their methods of mounting. 2 Types, methods of mounting, and dimensions The guide pillars represented in Figure 1 illustrate the types

17、 only; these representations shall not influence the manufacturers design. ISO 2013 All rights reserved 1BS ISO 9182-1:2013ISO 9182-1:2013(E) The detailed dimensions of each type of guide pillar are given in the appropriate part of ISO 9182. Figure 2 shows an alternative form for guide pillar end. T

18、ype A1 Straight guide pillars Type A2 Straight guide pillars with end- locking and locking ring Type B1 End-locking guide pillars Type B2 End-locking guide pillars with lubri- cating grooves Type A Straight guide pillars (see ISO 9182-2) Type B End-locking guide pillars (see ISO 9182-3) Type C Guide

19、 pillars with taper lead and bush (see ISO 9182-4) Type D End-locking guide pillars with flange (see ISO 9182-5) Figure 1 Guide pillar types Key 1 radius Figure 2 Alternative form for guide pillar end2 ISO 2013 All rights reservedBS ISO 9182-1:2013BS ISO 9182-1:2013ISO 9182-1:2013(E) ISO 2013 All ri

20、ghts reserved IC S 25.120.10 Price based on 2 pagesThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services. BSI is incorporated by Royal Charter. British Standards and other standardizati

21、on products are published by BSI Standards Limited. British Standards Institution (BSI) BSI Group Headquarters 389 Chiswick High Road London W4 4AL UK About us We bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into sta

22、ndards -based solutions. The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals. Information on standards We can

23、 provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre. Buying standards You can buy and download PDF versions of BSI publications, including British and a

24、dopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team. Subscriptions Our range of subscri

25、ption services are designed to make using standards easier for you. For further information on our subscription products go to With British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7

26、 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to B

27、SI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit With a Multi-User Network Licence (MUNL) you are able to host standard

28、s publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is current. For further information, email . Revisions Our British Standards and other publications are updated by amendment

29、or revision. We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre. Copyright All the data, software and documentation set out in all Briti

30、sh Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use. Except as

31、permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. Details and advice can be obtained from the Co

32、pyright & Licensing Department. Useful Contacts: Customer Services Tel: +44 845 086 9001 Email (orders): Email (enquiries): Subscriptions Tel: +44 845 086 9001 Email: Knowledge Centre Tel: +44 20 8996 7004 Email: Copyright & Licensing Tel: +44 20 8996 7070 Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW