BS ISO 9182-2-2013 Tools for pressing Guide pillars Type A straight pillars《冲压工具 导柱 A型 直导柱》.pdf

1、BSI Standards Publication BS ISO 9182-2:2013 Tools for pressing Guide pillars Part 2: Type A, straight pillarsBS ISO 9182-2:2013 BRITISH STANDARD National foreword This British Standard is the UK implementation of ISO 9182-2:2013. It supersedes BS 7568-26:1993 which is withdrawn. The UK participatio

2、n in its preparation was entrusted to Technical Committee MTE/12, Tools for pressing and moulding. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are res

3、ponsible for its correct application. The British Standards Institution 2013. Published by BSI Standards Limited 2013 ISBN 978 0 580 76975 7 ICS 25.060.10; 25.120.10 Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the author

4、ity of the Standards Policy and Strategy Committee on 31 December 2013. Amendments issued since publication Date Text affectedBS ISO 9182-2:2013 ISO 2013 Tools for pressing Guide pillars Part 2: Type A, straight pillars Outillage de presse Colonnes de guidage Partie 2: Type A, colonnes droites INTER

5、NATIONAL STANDARD ISO 9182-2 Second edition 2013-12-15 Reference number ISO 9182-2:2013(E)BS ISO 9182-2:2013ISO 9182-2:2013(E)ii ISO 2013 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO 2013 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utiliz

6、ed otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright

7、 office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in SwitzerlandBS ISO 9182-2:2013ISO 9182-2:2013(E) ISO 2013 All rights reserved iii Contents Page Foreword iv 1 Scope . 1 2 Dimensions . 1 3 Material 3 4 Designati

8、on 3 Bibliography 4BS ISO 9182-2:2013ISO 9182-2:2013(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees

9、. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the Intern

10、ational Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the diff

11、erent types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO sha

12、ll not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any trade name used in this document

13、is information given for the convenience of users and does not constitute an endorsement. For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TB

14、T) see the following URL: Foreword - Supplementary information The committee responsible for this document is ISO/TC 29, Small tools, Subcommittee SC 8, Tools for pressing and moulding. This second edition results from the reinstatement of ISO 9182-2:1992 which was withdrawn in 2007 and with which i

15、t is technically identical. ISO 9182 consists of the following parts, under the general title Tools for pressing Guide pillars: Part 1: Types Part 2: Type A, straight pillars Part 3: Type B, end-locking pillars Part 4: Type C, pillars with taper lead and bush Part 5: Type D, end-locking pillars with

16、 flangeiv ISO 2013 All rights reservedBS ISO 9182-2:2013INTERNATIONAL ST ANDARD ISO 9182-2:2013(E) Tools for pressing Guide pillars Part 2: Type A, straight pillars 1 Scope This part of ISO 9182 specifies the dimensions and tolerances, in millimetres, of guide pillars, type A, intended for use in pr

17、ess tools. These guide pillars can be straight, type A1 (see Figure 1), or straight with end-locking and locking ring, type A2 (see Figure 2). It gives guidance on the materials and specifies the hardness and the designation of guide pillars which meet the requirements of this part of ISO 9182. 2 Di

18、mensions The dimensions of straight guide pillar (type A1) shall conform to the indications of Figure 1 and Table 1. The dimensions of straight guide pillar with end-locking and locking ring (type A2) shall conform to the indications in Figure 2 and Table 1. ISO 2013 All rights reserved 1BS ISO 9182

19、-2:2013ISO 9182-2:2013(E) Surface roughness value in micrometres Key 1 alternative 2 radius 3 centres a Optional. b Slightly rounded. The values of the radii are left to the manufacturers discretion. Figure 1 Type A1, straight guide pillar Surface roughness value in micrometres Key 1 alternative 2 r

20、adius 3 centres a Optional. b Slightly rounded. The values of the radii are left to the manufacturers discretion. Figure 2 Type A2, straight guide pillar with end-locking and locking ring2 ISO 2013 All rights reservedBS ISO 9182-2:2013ISO 9182-2:2013(E) Table 1 d 1 12 16 20 25 32 40 50 63 80 100 d 2

21、 10,3 14,3 17, 3 22,3 27, 8 35,8 45,8 56,8 73,8 93,8 l 1min. 4 4 4 6 6 6 8 8 8 8 l 3 1,7 1,7 2,7 2,7 4,2 4,2 4,2 6,2 6,2 6,2 l 4 4 4 6 6 10 10 10 16 16 16 l 80 90 100 112 125 140 160 180 200 224 250 280 315 355 400 450 500 NOTE 1 , standardized dimension. NOTE 2 To prevent an incorrect assembly of t

22、he upper and lower plates of the die set in relation to each other, the following values of d 1are recommended: 11, 15, 19, 24, 30, 38, 48, and 60. 3 Material The material is left to the manufacturers discretion and the hardness shall be (60 ) HRC. 4 Designation Guide pillars for press tools in acco

23、rdance with this part of ISO 9182 shall be designated by a) “Guide pillar”; b) a reference to this part of ISO 9182, i.e. ISO 9182-2; c) its type; d) its diameter, d 1 , in millimetres; e) its overall length, l, in millimetres. EXAMPLE A guide pillar, type A1, of diameter d 1= 12 mm and overall leng

24、th l = 80 mm is designated as follows:Guide pillar ISO 91822 A1 12 80 ISO 2013 All rights reserved 3BS ISO 9182-2:2013ISO 9182-2:2013(E) Bibliography 1 ISO 6508-1:2005, Metallic materials Rockwell hardness test Part 1: Test method (scales A, B, C, D, E, F, G, H, K, N, T) 2 ISO 9182-1:2013, Tools for

25、 pressing Guide pillars Part 1: Types4 ISO 2013 All rights reservedBS ISO 9182-2:2013BS ISO 9182-2:2013ISO 9182-2:2013(E) ISO 2013 All rights reserved IC S 25.120.10 Price based on 4 pagesThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other

26、standards-related publications, information and services. BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited. British Standards Institution (BSI) BSI Group Headquarters 389 Chiswick High Road London W4 4AL UK About us We

27、bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions. The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation proc

28、ess. Organizations of all sizes and across all sectors choose standards to help them achieve their goals. Information on standards We can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Custom

29、er Services team or Knowledge Centre. Buying standards You can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from

30、other Standards Development Organizations, hard copies can be ordered from our Customer Services team. Subscriptions Our range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to With British Standards Online (BSOL

31、) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of

32、 standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BS

33、I Subscribing Member and the benefits of membership, please visit With a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your do

34、cumentation is current. For further information, email . Revisions Our British Standards and other publications are updated by amendment or revision. We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Stan

35、dard or other BSI publication please inform the Knowledge Centre. Copyright All the data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that owns copyright in the information used (such as t

36、he international standardization bodies) and has formally licensed such information to BSI for commercial publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means e

37、lectronic, photocopying, recording or otherwise without prior written permission from BSI. Details and advice can be obtained from the Copyright & Licensing Department. Useful Contacts: Customer Services Tel: +44 845 086 9001 Email (orders): Email (enquiries): Subscriptions Tel: +44 845 086 9001 Email: Knowledge Centre Tel: +44 20 8996 7004 Email: Copyright & Licensing Tel: +44 20 8996 7070 Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW