BS ISO 9182-5-2013 Tools for pressing Guide pillars Type D end-locking pillars with flange《冲压工具 导柱 D型 末端锁定带法兰的柱》.pdf

1、BSI Standards Publication BS ISO 9182-5:2013 Tools for pressing Guide pillars Part 5: Type D, end-locking pillars with flangeBS ISO 9182-5:2013 BRITISH STANDARD National foreword This British Standard is the UK implementation of ISO 9182-5:2013. It supersedes BS 7568-29:1993 which is withdrawn. The

2、UK participation in its preparation was entrusted to Technical Committee MTE/12, Tools for pressing and moulding. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract

3、. Users are responsible for its correct application. The British Standards Institution 2013. Published by BSI Standards Limited 2013 ISBN 978 0 580 76978 8 ICS 25.060.10; 25.120.10 Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published u

4、nder the authority of the Standards Policy and Strategy Committee on 31 December 2013. Amendments issued since publication Date T e x t a f f e c t e dBS ISO 9182-5:2013 ISO 2013 Tools for pressing Guide pillars Part 5: Type D, end-locking pillars with flange Outillage de presse Colonnes de guidage

5、Partie 5: Type D, colonnes retenue infrieure, dmontables INTERNATIONAL STANDARD ISO 9182-5 Second edition 2013-12-15 Reference number ISO 9182-5:2013(E)BS ISO 9182-5:2013ISO 9182-5:2013(E)ii ISO 2013 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO 2013 All rights reserved. Unless otherwise spec

6、ified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or I

7、SOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in SwitzerlandBS ISO 9182-5:2013ISO 9182-5:2013(E) ISO 2013 All rights reserved iii Contents Page For

8、eword iv 1 Scope . 1 2 Normative references 1 3 Dimensions . 1 4 Material 3 5 Designation 3 Bibliography 5BS ISO 9182-5:2013ISO 9182-5:2013(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of pre

9、paring International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in

10、 liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IE

11、C Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility

12、that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent

13、 declarations received (see www.iso.org/patents). Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement. For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as inform

14、ation about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information The committee responsible for this document is ISO/TC 29, Small tools, Subcommittee SC 8, Tools for pressing and moulding. This second edition results

15、 from the reinstatement of ISO 9182-5:1992 which was withdrawn in 2007 and with which it is technically identical. ISO 9182 consists of the following parts, under the general title Tools for pressing Guide pillars: Part 1: Types Part 2: Type A, straight pillars Part 3: Type B, end-locking pillars Pa

16、rt 4: Type C, pillars with taper lead and bush Part 5: Type D, end-locking pillars with flangeiv ISO 2013 All rights reservedBS ISO 9182-5:2013INTERNATIONAL ST ANDARD ISO 9182-5:2013(E) Tools for pressing Guide pillars Part 5: Type D, end-locking pillars with flange 1 Scope This part of ISO 9182 spe

17、cifies the dimensions and tolerances, in millimetres, of guide pillars, type D, end-locking pillar with flange, intended for use in press tools. It gives guidance on the materials and specifies the hardness and the designation of guide pillars which meet the requirements of this part of ISO 9182. 2

18、Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendme

19、nts) applies. ISO 6753-1:2005, Tools for pressing and moulding Machined plates Part 1: Machined plates for press tools 3 Dimensions The dimensions of end-locking guide pillar with flange (type D) shall conform to the indications of Figure 1 and Table 1. ISO 2013 All rights reserved 1BS ISO 9182-5:20

20、13ISO 9182-5:2013(E) Key 1 alternative 2 radius 3 centres a Optional. b Slightly rounded. The values of the radii are left to the manufacturers discretion. c The tolerance j6 can be reduced for a certain part of length l 2 , to act as a pilot for fitting purposes. Figure 1 End-locking guide pillar w

21、ith flange2 ISO 2013 All rights reservedBS ISO 9182-5:2013ISO 9182-5:2013(E) Table 1 d 1 12 16 20 25 32 40 50 63 80 100 d 2 16 20 25 32 40 50 63 80 100 125 l 1min. 4 4 4 6 6 6 8 8 8 8 l 2min. 12 16 20 25 32 40 50 50 63 63 l 63 80 90 100 112 125 140 160 180 200 224 250 280 315 355 400 450 500 NOTE 1

22、, standardized dimension. NOTE 2 Larger values of l 2shall be chosen as a function of other dimensions such as plate thickness in accordance with ISO 6753-1. NOTE 3 To prevent an incorrect assembly of the upper and lower plates of the die set in relation to each other, the following values of d 1are

23、 recommended: 11, 15, 19, 24, 30, 38, 48, and 60. 4 Material The material is left to the manufacturers discretion and the hardness shall be (62 ) HRC. 5 Designation Guide pillars for press tools in accordance with this part of ISO 9182 shall be designated by a) “Guide pillar”; b) a reference to this

24、 part of ISO 9182, i.e. ISO 9182-5; c) its type; d) its diameter, d 1 , in millimetres; e) the bush length, l 2 , in millimetres; f) the length, l, in millimetres. ISO 2013 All rights reserved 3BS ISO 9182-5:2013ISO 9182-5:2013(E) EXAMPLE A guide pillar, type D, of diameter d 1= 12 mm, length l 2= 1

25、2 mm, and a length l = 63 mm is designated as follows:Guide pillar ISO 91825 D 12 12 634 ISO 2013 All rights reservedBS ISO 9182-5:2013ISO 9182-5:2013(E) Bibliography 1 ISO 6508-1:2005, Metallic materials Rockwell hardness test Part 1: Test method (scales A, B, C, D, E, F, G, H, K, N, T) 2 ISO 9182-

26、1:2013, Tools for pressing Guide pillars Part 1: Types ISO 2013 All rights reserved 5BS ISO 9182-5:2013ISO 9182-5:2013(E) ISO 2013 All rights reserved ICS 25.120.10 Price based on 5 pagesThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other s

27、tandards-related publications, information and services. BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited. British Standards Institution (BSI) BSI Group Headquarters 389 Chiswick High Road London W4 4AL UK About us We b

28、ring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions. The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation proce

29、ss. Organizations of all sizes and across all sectors choose standards to help them achieve their goals. Information on standards We can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Custome

30、r Services team or Knowledge Centre. Buying standards You can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from o

31、ther Standards Development Organizations, hard copies can be ordered from our Customer Services team. Subscriptions Our range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to With British Standards Online (BSOL)

32、 youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of

33、standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI

34、 Subscribing Member and the benefits of membership, please visit With a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your doc

35、umentation is current. For further information, email . Revisions Our British Standards and other publications are updated by amendment or revision. We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Stand

36、ard or other BSI publication please inform the Knowledge Centre. Copyright All the data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that owns copyright in the information used (such as th

37、e international standardization bodies) and has formally licensed such information to BSI for commercial publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means el

38、ectronic, photocopying, recording or otherwise without prior written permission from BSI. Details and advice can be obtained from the Copyright & Licensing Department. Useful Contacts: Customer Services Tel: +44 845 086 9001 Email (orders): Email (enquiries): Subscriptions Tel: +44 845 086 9001 Email: Knowledge Centre Tel: +44 20 8996 7004 Email: Copyright & Licensing Tel: +44 20 8996 7070 Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW