BS ISO 9183-2-2011 Tools for pressing Wear plates for press dies Type B《压力工具 冲压模具用耐磨板 B型》.pdf

1、raising standards worldwide NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BSI Standards Publication BS ISO 9183-2:2011 Tools for pressing Wear plates for press dies Part 2: Type BBS ISO 9183-2:2011 BRITISH STANDARD National foreword This British Standard is the UK implementa

2、tion of ISO 9183-2:2011. It supersedes BS 7568-33:1993 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee MTE/12, Tools for pressing and moulding. A list of organizations represented on this committee can be obtained on request to its secretary. This pub

3、lication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. BSI 2011 ISBN 978 0 580 73920 0 ICS 25.120.10 Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published unde

4、r the authority of the Standards Policy and Strategy Committee on 30 September 2011. Amendments issued since publication Date T e x t a f f e c t e dBS ISO 9183-2:2011Reference number ISO 9183-2:2011(E) ISO 2011INTERNATIONAL STANDARD ISO 9183-2 Second edition 2011-09-15 Tools for pressing Wear plate

5、s for press dies Part 2: Type B Outillage de presse Plaques de frottement Partie 2: Type B BS ISO 9183-2:2011 ISO 9183-2:2011(E) COPYRIGHT PROTECTED DOCUMENT ISO 2011 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any mean

6、s, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyri

7、ghtiso.org Web www.iso.org Published in Switzerland ii ISO 2011 All rights reservedBS ISO 9183-2:2011 ISO 9183-2:2011(E) ISO 2011 All rights reserved iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The w

8、ork of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-govern

9、mental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The

10、 main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.

11、 Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 9183-2 was prepared by Technical Committee ISO/TC 29, Small tools, Subcommittee SC 8, Tools for

12、pressing and moulding. This second edition cancels and replaces the first edition (ISO 9183-2:1993), of which it constitutes a minor revision. In particular, the indication of surface textures has been updated in accordance with ISO 1302:2002. ISO 9183 consists of the following parts, under the gene

13、ral title Tools for pressing Wear plates for press dies: Part 1: Type A Part 2: Type B BS ISO 9183-2:2011BS ISO 9183-2:2011 INTERNATIONAL STANDARD ISO 9183-2:2011(E) ISO 2011 All rights reserved 1Tools for pressing Wear plates for press dies Part 2: Type B 1 Scope This part of ISO 9183 specifies the

14、 basic dimensions and tolerances, in millimetres, of wear plates, type B, intended for use mainly in large presses. lt also specifies the size and positions of the clearance holes for attachment. lt gives guidance on the materials and hardness, and specifies the designation of wear plates for press

15、dies, type B, which meet the requirements of this part of ISO 9183. 2 Dimensions The dimensions of wear plates for press dies shall be in accordance with the indications of Figures 1 and 2 and Table 1. Dimensions in millimetres Surface roughness values in micrometres Figure 1 Dimensions BS ISO 9183-

16、2:2011 ISO 9183-2:2011(E) 2 ISO 2011 All rights reserveda) b) d) e) g) h) c) f) Figure 2 Clearance hole patterns BS ISO 9183-2:2011 ISO 9183-2:2011(E) ISO 2011 All rights reserved 3Table 1 Dimensions of wear plates for press dies b 1 0 2 l 1 0,1 t nom. b 20,25 b 30,1 b 40,1 l 20,1 l 30,1 l 40,1 Figu

17、re Number of clearance holes for attachment 70 100 20 25 20 20 50 2 a) 2 150 10 50 2 b) 3 200 20 100 70 2 c) 4 100 100 50 30 50 45 2 d) 3 150 50 75 45 2 e) 4 200 50 100 70 2 c) 4 250 50 100 70 2 f) 5 300 50 100 70 2 g) 6 150 100 75 25 50 2 h) 4 150 100 75 45 2 e) 4 200 100 100 70 2 c) 4 250 100 100

18、70 2 f) 5 300 100 100 70 2 g) 6 200 100 100 50 50 2 h) 4 3 Material and corresponding hardness Material and hardness are left to the manufacturers discretion. 4 Designation Wear plates in accordance with this part of ISO 9183 shall be designated by: a) “wear plate”; b) reference to this part of ISO

19、9183, i.e. ISO 9183-2:2011; c) its type (B); d) its width, b 1 , in millimetres; e) its length, l 1 , in millimetres. EXAMPLE The designation for a wear plate for press dies, type B, of width b 1= 70 mm and length l 1= 100 mm is as follows: Wear plate ISO 9183-2 B - 70 100 BS ISO 9183-2:2011 ISO 918

20、3-2:2011(E) 4 ISO 2011 All rights reservedBibliography 1 ISO 1302:2002, Geometrical Product Specifications (GPS) Indication of surface texture in technical product documentation BS ISO 9183-2:2011BS ISO 9183-2:2011 ISO 9183-2:2011(E) ICS 25.120.10 Price based on 4 pages ISO 2011 All rights reserved

21、This page deliberately left blankBSI is the independent national body responsible for preparing British Standards and other standards-related publications, information and services. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Br

22、itish Standards Institution (BSI) raising standards worldwide BSI Group Headquarters 389 Chiswick High Road London W4 4AL UK Tel +44 (0)20 8996 9001 Fax +44 (0)20 8996 7001 British Standards are updated by amendment or revision. Users of British Stan- dards should make sure that they possess the la

23、test amendments or editions. It is the constant aim of BSI to improve the quality of our products and serv- ices. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical com- mittee responsible, the identity of w

24、hich can be found on the inside front cover. Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001 BSI offers Members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001 Email:

25、 Buying standards You may buy PDF and hard copy versions of standards directly using a credit card from the BSI Shop on the website In addition all orders for BSI, international and foreign standards publications can be addressed to BSI Customer Services. Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 89

26、96 7001 Email: In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and interna

27、tional standards through its Knowledge Centre. Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005 Email: Various BSI electronic information services are also available which give details on all its products and services. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: BSI Subscribing Membe

28、rs are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Ad- ministration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to Briti

29、sh Standards via British Standards Online can be found at Further information about BSI is available on the BSI website at www.bsi- Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Ex- ce

30、pt as permitted under the Copyright, Designs and Patents Act 1988 no ex- tract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, i

31、n the course of implementing the standard of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copy- right & Licensing Manager. Tel: +44 (0)20 8996 7070 Email: