BS ISO 9343-2004 Pliers and nippers - Slip joint pliers - Dimensions and test values《夹扭钳和剪切钳 鲤鱼钳 尺寸和试验值》.pdf

1、BRITISH STANDARD BS ISO 9343:2004 Pliers and nippers Slip joint pliers Dimensions and test values ICS 25.140.30 BS ISO 9343:2004 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 10 December 2004 BSI 10 December 2004 ISBN 0 580 45044 9 National

2、 foreword This British Standard reproduces verbatim ISO 9343:2004 and implements it as the UK national standard. It supersedes BS 3087-11:1991, which is withdrawn. The UK participation in its preparation was entrusted by Technical Committee MTE/15, Hand tools, to Subcommittee MTE/15/13, Assembly too

3、ls for screws and nuts, pliers and nippers, which has the responsibility to: A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement international publications referred to in this document may be fou

4、nd in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are resp

5、onsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep

6、the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the ISO title page, pages ii and iii, a blank page, pages 1 to 3 and a back cover. The BSI copyright notice

7、 displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date Comments Reference number ISO 9343:2004(E)INTERNATIONAL ADNATSDR ISO 9343 ceSond deition -400251-90 Pliers and nippers Slip joint pliers Dimensions and test values Pinces et ten

8、ailles Pinces rglables deux positions Dimensions et valeurs dessai Referecne unbmer OSI :3439)E(4002 OSI 4002INTERNATIONAL STANDARD ISO 9343 Second edition 2004-09-15 dna sreilP pinpej pilS sronit sreilp nemiDsoina snset dt valuse cniPse et teanlisel iPcnes rbalgsel edxu soptioins miD sneisno v teal

9、rues sedsai BSISO9343:2004 ii BSISO9343:2004 iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each m

10、ember body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International

11、Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards a

12、dopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of p

13、atent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 9343 was prepared by Technical Committee ISO/TC 29, Small tools, Subcommittee SC 10, Assembly tools for screws and nuts, pliers and nippers. This second edition cancels and replaces the first edition (

14、ISO 9343:1988) which has been technically revised. BSISO9343:2004blankINTENRATIONAL TSANDADR IS:3439 O4002(E)1Pliers and nippers Slip joint pliers Dimensions and test values 1 Scope This International Standard specifies the principal dimensions of slip joint pliers, designated as No. 206 in ISO 5742

15、, and the test values, in order to verify their aptitude to function in conformity with ISO 5744. The general technical requirements are given in ISO 5743. The slip joint pliers illustrated in this International Standard are examples only and are not intended to affect the manufacturers design. 2 No

16、rmative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 5743, Pliers and nippers G

17、eneral technical requirements ISO 5744:2004, Pliers and nippers Methods of test 3 Dimensions and test value The principal dimensions of slip joint pliers are shown in Figure 1 and given in Table 1. For the pliers provided with a comfort grip, the opening of the handle must be defined with this. Afte

18、r the load test, the permanent set, s, shall not exceed the value given in Table 1. If distance l 1is not suitable for the load test, the formula given in ISO 5744:2004, 4.2 shall be used. BSISO9343:20042 aJaws parallel. bt 2u t 1 . cF = load applied in load test. Figure 1 Slip joint pliers Table 1

19、Slip joint pliers, principal dimensions and load test values Load test l w 1w 3w 4t 1l 1l 3g Load F Maximum permanent set s a15 5 + max. max. max. 5 min. max. mm mm mm mm mm mm mm mm N mm 160 8 48 32 8 10 80 30 7 1 000 1 180 9 49 35 10 11 90 35 8 1 120 1 200 10 50 40 12,5 12,5 100 35 9 1 250 1 250 1

20、0 50 45 12,5 12,5 125 40 10 1 400 1,5 as = w 1 w 2(see ISO 5744). 4 Designation EXAMPLE Slip joint pliers, number 206 in accordance with ISO 5742, with a nominal length l = 180 mm are designated as follows: Slip joint pliers 206 - ISO 9343 - 180 5 Marking Marking shall be in accordance with ISO 5743

21、. BSISO9343:2004 3Bibliography 1 ISO 5742, Pliers and nippers Nomenclature BSISO9343:2004BS ISO 9343:2004 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards

22、in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of ou

23、r products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996

24、7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 89

25、96 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise req

26、uested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and servi

27、ces. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact M

28、embership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-. Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- Further information about BSI is available on the BSI website at http:/www.bsi-. C

29、opyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitt

30、ed in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.