BS ISO 9749-2001 Stud-ends in corrosion-resistant steel swaged on aircraft control wire rope - Dimensions and loads《航空器操纵钢丝绳上的锻制耐腐蚀钢螺柱端 尺寸规格及载荷》.pdf

1、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BRITISH STANDARD AEROSPACE SERIES BS ISO 9

2、749:2000 ICS 49.035 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Stud-ends, in corrosion-resistant steel, swaged on aircraft control wire rope Dimensions and loadsThis British Standard, having been prepared under the direction of the Engineering Sector Committee, was publis

3、hed under the authority of the Standards Committee and comes into effect on 15 March 2001 BSI 03-2001 ISBN 0 580 35044 4 BS ISO 9749:2000 Amendments issued since publication Amd. No. Date Comments National foreword This British Standard reproduces verbatim ISO 9749:2000 and implements it as the UK n

4、ational standard. The UK participation in its preparation was entrusted to Technical Committee ACE/14, Aerospace details and parts, which has the responsibility to: aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation,

5、or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implemen

6、t international publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include a

7、ll the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the ISO ti

8、tle page, pages ii and iii, a blank page, pages 1 to 5 and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued.A Referencenumbe r ISO9748:2000 (E) INTERNATIONAL STANDARD ISO 9749 Firstedition 20001215 AerospaceStudends,incorrosion resistantst

9、eel,swagedonaircraftcontrol wireropeDimensionsandloads AronautiqueetespaceEmboutstendeurs,enacierrsistantla corrosion,sertirsurcblesdecommandedaronefsDimensionset chargesISO9749:2000(E) iiISO9749:2000(E) iii Foreword ISO(theInternationalOrganizationforStandardization)isaworldwidefederationofnational

10、standardsbodies(ISO memberbodies).TheworkofpreparingInternationalStandardsisnormallycarriedoutthroughISOtechnical committees.Eachmemberbodyinterestedinasubjectforwhichatechnicalcommitteehasbeenestablishedhas therighttoberepresentedonthatcommittee.Internationalorganizations,governmentalandnongovernme

11、ntal,in liaisonwithISO,alsotakepartinthework.ISOcollaboratescloselywiththeInternationalElectrotechnical Commission(IEC)onallmattersofelectrotechnicalstandardization. InternationalStandardsaredraftedinaccordancewiththerulesgivenintheISO/IECDirectives,Part3. DraftInternationalStandardsadoptedbythetech

12、nicalcommitteesarecirculatedtothememberbodiesforvoting. PublicationasanInternationalStandardrequiresapprovalbyatleast75%ofthememberbodiescastingavote. InternationalStandardISO9749waspreparedbyTechnicalCommitteeISO/TC20, Aircraftandspacevehicles, SubcommitteeSC12, Mechanicalsystemparts . AnnexAformsa

13、normativepartofthisInternationalStandard.INTERNATIONALSTANDARD OISO9749:2000(E) 1 AerospaceStudends,incorrosionresistantsteel,swagedon aircraftcontrolwireropeDimensionsandloads 1Scope ThisInternationalStandardspecifiesthecharacteristicsofstudendsincorrosionresistantsteelswagedonaircraft controlwirer

14、ope. 2Normative references Thefollowingnormativedocumentscontainprovisionswhich,throughreferenceinthistext,constituteprovisionsofthis InternationalStandard.Fordatedreferences,subsequentamendmentsto,orrevisionsof,anyofthesepublicationsdo notapply.However,partiestoagreementsbasedonthisInternationalSta

15、ndardareencouragedtoinvestigatethe possibilityofapplyingthemostrecenteditionsofthenormativedocumentsindicatedbelow.Forundatedreferences, thelatesteditionofthenormativedocumentreferredtoapplies.MembersofISOandIECmaintainregistersof currentlyvalidInternationalStandards. ISO20201:1997, Aerospace Prefor

16、medflexiblesteelwireropeforaircraftcontrols Part 1:Dimensionsand loads. ISO8074:1985, AerospaceSurfacetreatmentofausteniticstainlesssteelparts. ISO9761:1999, Aerospace Loc kingc lips,inc orrosion resistants teel,for air craftc ontrolwir er opetur nbuckles Dimensions. ISO10955:1999, AerospaceEndfitti

17、ngsandturnbarrelsforaircraftcontrolwireropeTechnicalspecification . ISO13715:2000, TechnicaldrawingsEdgesofundefinedshapeVocabularyandindicationondrawings . EN2465 1) , AerospaceseriesSteelFEPA11SoftenedBars D e 100mm . 2) SAEAMS2431/6A, PeeningMedia,GlassShot. SAEAMS5639G, Steel,CorrosionResistant,

18、Bars,Wire,Forgings,Tubing,andRings,19Cr10Ni,SolutionHeat Treated. SAEAMS5641F, Steel,CorrosionResistant,Bars,Wire,andForgings,18.5Cr10Ni0.22SeFreeMachining; SwagingorUpsetting,SolutionHeatTreated. 3 Configuration,dimensions,loadsandmasses Configuration,dimensions,loadsandmassesshallbeinaccordancewit

19、hFigure1andTable1. Studendsshouldbemanufacturedfromahexagonalbar(type1);however,wherebarsofhexagonalcrosssectionare difficulttoobtain,theymaybeproducedfrommilledflats(type2). 1) Tobepublished. 2) AECMA.ISO9749:2000(E) 2 Dimensionsinmillimetres/Surfaceroughnessinmicrometres a Thread d Slotforlockingc

20、lipinaccordancewithISO9761 b Pitchdiameter e Groovemarkingthreadonleftonly;thebottomofthegrooveshallnotreachtheacrossflat. c Marking Figure1ISO9749:2000(E) 3 Table1 Dimensionsinmillimetres Wirerope Thread a D 1 D 2 D 3 D 4 D 5 D 6 D 7 L 1 L 2 L 3 L 4 L 5 L 6 L 7 MP Masse Minimum g/piece breaking Cod

21、e Nom. lim. Code lim. load b diam. b nom. dev. min. max. -012 0 , 0 012 + , 0 025 + , -015 0 , H13 1 0,5 0,5 0,5 0 05 + , 0 1 + nom. div. 0,5 min. max. kN 16 1,6 MJ4 0,74h6h 2,9 -01 0 , 5,5 6 4,1 2 2,3 3,5 S 57 27,5 35 8 29 26 25 5 3,26 3,36 4,6 2,15 24 2,4 MJ5 0,84h6h 3,8 7,7 8,5 5,6 2,8 3 4,8 S 69

22、 27 42 10 35,5 32 30 7 4,18 4,33 10,2 4,45 1,5 L 82 40 0 1 + 11,4 32 3,2 MJ6 14h6h 4,6 6,4 3,6 3,9 5,6 S 81 27,5 49 12 43 39 37 5,1 5,27 14,2 8,9 -015 0 , L 97 49,5 16,3 40 4 MJ7 14h6h 5,6 8,8 9,5 7,5 4,4 4,8 6,4 S 93 27,5 56 14 49,5 45 43 8 6,09 6,27 22,1 12,45 L 111 49,5 25,5 48 4,8 MJ8 14h6h 6,6

23、11,1 12 9,1 5,2 5,6 8 2,5 S 105 27 63 16 56 51 49 0 15 + , 10 7,1 7,27 36,6 18,6 56 5,6 MJ10 1,254h6h 7,8 13,6 14,5 10,9 6 6,5 9,5 S 123 49 70 20 62,5 57 55 12 8,93 9,11 62,3 24,9 64 6,4 MJ12 1,254h6h 9,8 14,5 15,5 12,6 6,8 7,4 11 S 130 77 24 70 64 62 13 10,91 11,11 92 31,2 a InaccordancewithISO5855

24、2. b InaccordancewithISO20201. 4Material Corrosionresistantsteel(inaccordancewithannexA). 5Surface treatment Passivation(codeP)inaccordancewithISO8074orpeening(codeG)(inaccordancewithannexA). 6Designation EachstudendinaccordancewiththisInternationalStandardshallbedesignatedasshowninthefollowing exam

25、ple. EXAMPLE Wherethefollowingcodesareappliedforthethreaddirection: codeR:righthandthread; codeL:lefthandthread.ISO9749:2000(E) 4 7Marking ThemarkingpositionshallbeinaccordancewithFigure1. Inadditiontothemanufacturersownmarking,eachstudendinaccordancewiththisInternationalStandardshallbe markedusingt

26、heidentityblockspecifiedinclause6. Themarkingmethodisatthemanufacturersoption. 8Technical specification InaccordancewithISO10955.ISO9749:2000(E) 5 AnnexA (normative) Correspondencebetweennationalstandards Thisannexestablishesacorrespondencebetweendifferentmaterialsandsurfacetreatmentstandardsfromcer

27、tain usercountries.Othermemberbodiesareinvitedtodeclaretheirmaterialsandsurfacetreatmentstandardsinthis annex. ThematerialsandprocessescitedinTables A.1andA.2areconsideredtobeequivalent,assumingthatthe requirementsforstudendsspecifiedinthisInternationalStandardarerespected. TableA.1Europeanstandards

28、 Code Material Surfacetreatment Family Standard Nature Standard No Corrosionresistantsteel EN2465 Passivation ISO8074 code Peening SAEAMS 2431/6A TableA.2U.S.standards Code Material Surfacetreatment Family Standard Nature Standard No code Corrosionresistantsteel SAEAMS5639 or Passivation ISO8074 SAE

29、AMS5641 P eening SAEAMS 2431/6ABS ISO 9749:2000 BSI 389 Chiswick High Road London W4 4AL | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |

30、 | | | | | | | | | | | | | | | | | | | | | BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standar

31、ds are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using t

32、his British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically rec

33、eive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. Standards are also available from the BSI website at http:/www.bsi-. In response to orders fo

34、r international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and

35、 its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developm

36、ents and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Further information about BSI is available on the BSI website at http:/www.bsi-. Copyright Copyright subsists

37、in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any mea

38、ns electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.