BS ISO 9803-1-2007 Vacuum technology - Mounting dimensions of pipeline fittings - Non knife-edge flange type《真空技术 管道配件的安装尺寸 非刀口法兰型》.pdf

1、BRITISH STANDARD BS ISO 9803-1:2007 Vacuum technology Mounting dimensions of pipeline fittings Part 1: Non knife-edge flange type ICS 23.160 BS ISO 9803-1:2007 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 29 June 2007 BSI 2007 ISBN 978 0 5

2、80 52950 4 National foreword This British Standard was published by BSI. It is the UK implementation of ISO 9803-1:2007. The UK participation in its preparation was entrusted to Technical Committee MCE/8, Compressors, pneumatic tools, pneumatic machines and vacuum technology. A list of organizations

3、 represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations. Am

4、endments issued since publication Amd. No. Date Comments Reference number ISO 9803-1:2007(E)INTERNATIONAL STANDARD ISO 9803-1 First edition 2007-05-15 Vacuum technology Mounting dimensions of pipeline fittings Part 1: Non knife-edge flange type Technique du vide Dimensions de montage des raccords de

5、 conduit Partie 1: Brides de type sans guillotine BS ISO 9803-1:2007ii iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO t

6、echnical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates clos

7、ely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draf

8、t International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this docum

9、ent may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 9803-1 was prepared by Technical Committee ISO/TC 112, Vacuum technology. This first edition of ISO 9803-1, together with ISO 9803-2, cancels and replaces ISO 9803:1993, whic

10、h has been technically revised. ISO 9803 consists of the following parts, under the general title Vacuum technology Mounting dimensions of pipeline fittings: Part 1: Non knife-edge flange type Part 2: Knife-edge flange type BS ISO 9803-1:2007iv Introduction ISO 9803:1993 defined only those pipeline

11、fittings whose flanges are non-bakable, as defined in ISO 1609 and ISO 2861-1. This revision divides ISO 9803 into two parts: this part of ISO 9803, in which fittings with non-bakable flanges are defined, and ISO 9803-2, in which fittings with bakable flanges as specified in ISO 3669 are defined. Th

12、is part of ISO 9803 deals with dimensions of pipeline fittings whose flanges are of non-bakable type, as defined in ISO 1609 and ISO 2861-1. BS ISO 9803-1:20071 Vacuum technology Mounting dimensions of pipeline fittings Part 1: Non knife-edge flange type 1 Scope This part of ISO 9803 specifies mount

13、ing dimensions for vacuum pipeline fittings (elbows, tees and crosses) of non-bakable and non knife-edge flange for nominal bores from 10 mm to 250 mm of the R5 series. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated referen

14、ces, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 1609, Vacuum technology Flange dimensions ISO 2861-1, Vacuum technology Quick-release couplings Dimensions Part 1: Clamped type 3 Terms and definitions F

15、or the purposes of this document, the terms and definitions given in ISO 1609 and ISO 2861-1 apply. 4 Requirements 4.1 Mounting dimensions of the vacuum pipeline fittings shall be as specified in Table 1. See Figures 1 to 3. 4.2 Flange dimensions shall be as specified in ISO 1609 and ISO 2861-1. One

16、 or more flange should be rotatable. 4.3 Bolt holes in the flanges specified in ISO 1609 shall be positioned as shown in Figure 4. Angle is a function of the number of bolt holes. BS ISO 9803-1:20072 Dimensions in millimetres Key e edge dimension Figure 1 Elbow Dimensions in millimetres Key e edge d

17、imension H length Figure 2 Tee BS ISO 9803-1:20073 Dimensions in millimetres Key e edge dimension H length Figure 3 Cross Key = 360 total number of bolt holes Figure 4 Position of bolt holes BS ISO 9803-1:20074 Table 1 Dimensions of pipeline fittings Dimensions in millimetres Edge dimension, e Lengt

18、h, H Perpendicularity or parallelism tolerance for the two mating faces for the two flanges specified in Nominal bore tolerance tolerance ISO 2861-1 ISO 1609 10 30/40 a60/80 a16 40 80 25 50 100 1,5 1 40 65 130 2 63 88 176 100 108 1,5 216 160 138 276 2 200 178 356 250 208 2 416 3 Not applicable 030 a

19、The latter value shall be used only for flanges specified in ISO 1609. BS ISO 9803-1:20075 Bibliography 1 ISO 3, Preferred numbers Series of preferred numbers 2 ISO 3669, Vacuum technology Bakable flanges Dimensions 3 ISO 9803-2, Vacuum technology Mounting dimensions of pipeline fittings Part 2: Kni

20、fe-edge flange type BS ISO 9803-1:2007BS ISO 9801-1:2007 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is i

21、ncorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if

22、anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating s

23、ervice called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersb

24、si-. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a w

25、ide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)

26、20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 700

27、2. Fax: +44 (0)20 8996 7001. Email: membershipbsi-. Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- Further information about BSI is available on the BSI website at http:/www.bsi-. Copyright Copyright subsists in all BSI publicatio

28、ns. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photoc

29、opying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.