BS ISO IEC 17991-2015 Information technology Office equipment Method for Measuring Scanning Productivity of Digital Multifunctional Devices《信息技术 办公设备 数字化多功能设备扫描生产力的测量方法》.pdf

1、BSI Standards Publication BS ISO/IEC 17991:2015 Information technology Office equipment Method for Measuring Scanning Productivity of Digital Multifunctional DevicesBS ISO/IEC 17991:2015 BRITISH STANDARD National foreword This British Standard is the UK implementation of ISO/IEC 17991:2015. The UK p

2、articipation in its preparation was entrusted to Technical Committee IST/3, IT Printers and Cartridges. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users ar

3、e responsible for its correct application. The British Standards Institution 2015. Published by BSI Standards Limited 2015 ISBN 978 0 580 84327 3 ICS 37.100.10 Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the authority of

4、 the Standards Policy and Strategy Committee on 31 March 2015. Amendments/corrigenda issued since publication Date T e x t a f f e c t e dInformation technology Office equipment Method for Measuring Scanning Productivity of Digital Multifunctional Devices Technologie de linformation quipement dOffic

5、e Mthode pour Productivit du Scanner d Appareils Multifonctionnels Numriques INTERNATIONAL STANDARD ISO/IEC 17991 Reference number ISO/IEC 17991:2015(E) First edition 2015-03-01 ISO/IEC 2015 BS ISO/IEC 17991:2015ii ISO/IEC 2015 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO/IEC 2015 All rights

6、 reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from eith

7、er ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ISO/IEC 17991:2015(E)BS ISO/IEC 17991:2015ISO/IEC 1799

8、1:2015(E)Foreword iv Introduction v 1 Scope . 1 2 Normative references 1 3 Terms and definitions . 1 4 Test Parameters and Conditions 3 4.1 Environment . 3 4.2 Voltage 4 4.3 Scanning Device Setup 4 4.4 Maintenance 5 4.5 Preparation of Test Targets (Test Charts) 5 5 Test Method 5 5.1 Test Setup 5 5.2

9、 Test Measurement Procedure 6 5.2.1 Overview . 6 5.2.2 Measurement for scanning productivity . 7 5.3 Test Method Process 9 5.3.1 Suggested Test Method Process Flow Chart . 9 5.3.2 Estimating the Set Count10 5.3.3 5 % Consistency Criteria 10 5.4 Performance Test .10 5.4.1 ADF Productivity Measurement

10、 10 5.4.2 Scan to Network Folder Productivity Measurement 12 6 Calculations and Treatment of Data 14 6.1 Calculations .14 6.2 1 Set Test .14 6.3 1 Set + 30 Seconds Test .14 7 Presentation of Results .15 Annex A (informative) Examples of report presentation .19 Annex B (informative) Example of full d

11、etailed report 21 Annex C (normative) Test targets for measurement of scanning productivity .24 Annex D (informative) Test using PC based scanning software .26 Bibliography .27 ISO/IEC 2015 All rights reserved iiiBS ISO/IEC 17991:2015ISO/IEC 17991:2015(E) Foreword ISO (the International Organization

12、 for Standardization) and IEC (the International Electrotechnical Commission) form the specialized system for worldwide standardization. National bodies that are members of ISO or IEC participate in the development of International Standards through technical committees established by the respective

13、 organization to deal with particular fields of technical activity. ISO and IEC technical committees collaborate in fields of mutual interest. Other international organizations, governmental and non-governmental, in liaison with ISO and IEC, also take part in the work. In the field of information te

14、chnology, ISO and IEC have established a joint technical committee, ISO/IEC JTC 1. The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types

15、 of document should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO and IEC shall not b

16、e held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any trade name used in this document is infor

17、mation given for the convenience of users and does not constitute an endorsement. For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT), see

18、the following URL: Foreword Supplementary information. The committee responsible for this document is ISO/IEC JTC 1, Information technology, Subcommittee SC 28, Office Equipment.iv ISO/IEC 2015 All rights reservedBS ISO/IEC 17991:2015ISO/IEC 17991:2015(E) Introduction The actual productivity measure

19、ment methods of copying and printing were published as ISO/IEC 24735 and ISO/IEC 24734. However, ISO/IEC 24735 contains no measurement method for the scanning productivity of multifunctional devices to be used for comparison and procurement of these machines. This International Standard provides a g

20、eneral method for measuring “scanning productivity” of the multifunctional devices. The International Standard also includes a test chart for scanning productivity measurement. It allows the manufacturers and the buyers of digital multifunctional devices to describe the productivity of various digit

21、al scanning devices with respect to representative office usage. ISO/IEC 2015 All rights reserved vBS ISO/IEC 17991:2015BS ISO/IEC 17991:2015Information technology Office equipment Method for Measuring Scanning Productivity of Digital Multifunctional Devices 1 Scope This International Standard speci

22、fies a method for determining scanning productivity by measuring “scanning speed” and “scan to network folder speed”. It includes test files, test setup procedure, test procedure, and the reporting requirements for the scanning productivity measurements. This International Standard is applicable to

23、black and white (B it can be affected by scan time, digital processing time, maintenance and the run time of the test. Note 3 to entry: A different term (“EFTP; effective throughput” for digital copying machines) is defined in ISO/IEC 24735. Note 4 to entry: As for scEFTP 30secF , measurement parame

24、ters involving the measurement of file transmission to a network folder are dependent on other factors like the computer and network configuration and represent relative values and not absolute values. 3.4 scanning Estimated Saturated Throughput scESAT rate at which a device scans pages measured fro

25、m full ejection of the last page of the first test set from ADF through the full ejection of the of the last page of the scanning sets (using suffix “ A ”) Note 1 to entry: scESAT is expressed in images per minute (ipm). Note 2 to entry: There are suffixes such as “ 1setA ” or “ 30secF ”. Each suffi

26、x is used to classify tests such as “1 set Test” or “1 set + 30 second test” for “ADF Productivity Measurement”(using suffix “ A ”) or “Scan to Network Folder Productivity Measurement”(using suffix “ F ”) test respectively. There is no measurement for “Scan to Network Folder Productivity Measurement

27、” of scESAT, scESAT 30secFdefined, therefore scESAT 1setAand scESAT 1setFare not used as classifications. 3.5 scanning First Set Out Time scFSOT number of seconds between the initiation of the job to full ejection of the last page of the first test set from ADF Note 1 to entry: There are suffixes su

28、ch as “ 1setA ” or “ 30secF ”. Each suffix is used to classify tests such as “1 set Test” or “1 set + 30 second test” for “ADF Productivity Measurement”(using suffix “ A ”) or “Scan to Network Folder Productivity Measurement”(using suffix “ F ”) test respectively. 3.6 full detailed report presentati

29、on of information including machine setup and measured test results 3.7 full report presentation of results including the scFSOT, scESAT, and scEFTP values in performance test as well as the calculated averages for each value 3.8 network folder speed rate at which a device scans and stores the scann

30、ed image file in the network folder to demonstrate the overall productivity of the device when scanning documents Note 1 to entry: Suffix “ F ” means “Scan to Network Folder Productivity Measurement”. For example, suffix such as “ 30secF ” means a test of “1 set + 30 second” test for “Scan to Networ

31、k Folder Productivity”.2 ISO/IEC 2015 All rights reservedBS ISO/IEC 17991:2015ISO/IEC 17991:2015(E) 3.9 performance test test used to evaluate productivity by providing scFSOT, scESAT, and scEFTP without using any special feature or mode, and includes both the simplex scanning mode and the duplex sc

32、anning modes if available 3.10 scanning Last Set Out Time scLSOT number of seconds between the initiation of the job to full ejection of the last page of the last test set from ADF Note 1 to entry: There are suffixes such as “ 1setA ” or “ 30secF ”. Each suffix is used to classify tests such as “1 s

33、et Test” or “1 set + 30 second test” for “ADF Productivity Measurement”(using suffix “ A ”) or “Scan to Network Folder Productivity Measurement”(using suffix “ F ”) test respectively. 3.11 simplex scanning use of a scanning device when only a single side of a sheet is scanned Note 1 to entry: Other

34、equivalent term is “single sided scanning”. 3.12 summary report presentation of results including the average overall scEFTP in the performance test for the scanning device default base line performance 3.13 test file digital file used for creating test targets 3.14 test set all of the pages of test

35、 target 3.15 test target hard copy document used for testing per the test method, and created from test file Note 1 to entry: An equivalent term is “test chart”. 3.16 time measurement number of seconds measured by timing device (stopwatch or other device) or by reading time display on the PC dock No

36、te 1 to entry: Suffixes such as “ SW ” and “ PC ” are used to show which time measurement is done; by timing device (stopwatch or other device) or by reading time display on the PC dock. For example, “t SW1A ” is the time measured via stopwatch or other device for completion of the first set out and

37、 “t PC1F ” is the time measured via PC clock for completion of the first set file written to the network folder. 3.17 scanning resolution resolution at which the document is scanned 4 Test Parameters and Conditions 4.1 Environment The test environment, including temperature and humidity, shall be wi

38、thin the ranges recommended by the manufacturer for operating the device. If no recommendation is available, the following ranges shall apply. ISO/IEC 2015 All rights reserved 3BS ISO/IEC 17991:2015ISO/IEC 17991:2015(E) Temperature: 18 C to 25 C Relative humidity: 30 % to 70 % NOTE The temperature a

39、nd humidity of the test environment should be recorded in the full detailed report (Annex B). 4.2 Voltage The scanning device shall be connected to a voltage supply within the manufacturer specified operating voltage range for the scanning device under test. NOTE The measurement should be made under

40、 no-load condition prior to each test. 4.3 Scanning Device Setup Place the scanning device on a horizontal surface and set up the scanning device according to the manufacturers recommendations. The scanning device shall be fully enclosed in its normal exterior cover. The machine shall be acclimated

41、in the test environment prior to conducting the test(s) at least 8 h. All images and scanning modes should be at their factory preset configuration for the scanning device. It is assumed that the settings listed in table 1 are common to all scanning devices. These listed settings shall be set to the

42、 manufacturers default or preset condition for the device. If a device has settings not listed in Table 1, they too shall be set to default settings. All settings shall be explicitly stated in either case of default or non-default settings. For scanning devices that have additional scan quality and

43、digital image processing features, those features shall be set to match their normal default condition, and included in the result reporting. Disabling manufacturer default installed features, routines or applications, is not allowed. The following preset values in the test shall be noted in the ful

44、l detailed report (Annex B). Table 1 Preset settings Preset item Preset value Example Mode Scanning resolution default 200 dpi Colour or grey scale/B&W default Colour Duplex/simplex default Simplex Original page size default A4 Paper feed orientation (long/short edge) default Long edge Scan destinat

45、ion default Shared network Storing File Type default PDF (multi) Auto scan quality adjustment default (Factory preset default setting) If the scanning device is setup with internal or external options such as memory as default, then these options shall be noted on the full detailed report format in

46、the configuration options as shown in Annex B, for example “160 GB HDD installed”. Additional tests may be conducted using other, non-default settings for the scanning device. The results of such additional tests shall be documented as having parameters that differ from the factory defaults and show

47、n in comparison to the default system parameter results. Optional paper sizes may be used for the scanning device tests such as A3 and/or 11” 17” size as appropriate for the test mode. When sheets of paper size other than A4/8.5”x11” are used, the sizes shall be indicated in the places of A4/8.5” 11” in the measurement results tables. When a comparison needs 4 ISO/IEC 2015 All rights reserved