BS ISO IEC 19395-2015 Information technology Sustainability for and by information technology Smart data centre resource monitoring and control《信息技术 针对并依据信息技术的可持续性 智能数据中心资.pdf

1、BSI Standards Publication BS ISO/IEC 19395:2015 Information technology Sustainability for and by information technology Smart data centre resource monitoring and controlBS ISO/IEC 19395:2015 BRITISH STANDARD National foreword This British Standard is the UK implementation of ISO/IEC 19395:2015. The

2、UK participation in its preparation was entrusted to Technical Committee ICT/-/1, Information systems co-ordination. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contr

3、act. Users are responsible for its correct application. The British Standards Institution 2015. Published by BSI Standards Limited 2015 ISBN 978 0 580 84222 1 ICS 35.040 Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the au

4、thority of the Standards Policy and Strategy Committee on 31 January 2015. Amendments issued since publication Date Text affectedBS ISO/IEC 19395:2015 Information technology Sustainability for and by information technology Smart data centre resource monitoring and control Technologies de linformatio

5、n Durabilit pour et par les technologies de linformation Surveillance des ressources et contrle des centres de donnes intelligents INTERNATIONAL STANDARD ISO/IEC 19395 Reference number ISO/IEC 19395:2015(E) First edition 2015-01-15 ISO/IEC 2015 BS ISO/IEC 19395:2015ii ISO/IEC 2015 All rights reserve

6、d COPYRIGHT PROTECTED DOCUMENT ISO/IEC 2015 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior wri

7、tten permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland

8、ISO/IEC 19395:2015(E)BS ISO/IEC 19395:2015ISO/IEC 19395:2015(E)Contents Page Foreword iv Introduction v 1 Scope . 1 2 Conformance . 2 3 Normative references 2 4 T erms, definitions and acr on yms 3 5 Domains . 4 5.1 Introduction 4 5.2 Base Domain . 5 5.2.1 CIM_System . 5 5.2.2 CIM_BaseMetricDefiniti

9、on . 5 5.2.3 CIM_BaseMetricValue 5 5.2.4 CIM_MetricDefForME . 6 5.2.5 CIM_MetricInstance . 6 5.2.6 CIM_RegisteredProfile . 6 5.2.7 CIM_SystemDevice 6 5.2.8 CIM_Component . 7 5.2.9 Metrics for fluid measurements . 7 5.2.10 CIM_NumericSensor 10 5.2.11 CIM_EnabledLogicalElementCapabilities 10 5.2.12 CI

10、M_ElementCapabilities .10 5.3 IT Domain .10 5.4 Power Domain 13 5.5 Fluid Domain .13 5.5.1 SDC_FluidConnection 15 5.5.2 SDC_FluidElement15 5.5.3 SDC_FluidMeasurementPoint 16 5.5.4 SDC_FluidTransferPort 16 5.5.5 SDC_CoolingSystem 16 5.5.6 SDC_CoolingSettingData .16 6 Properties .16 7 Messages 22 7.1

11、Commands and responses .23 7.1.1 GET . .23 7.1.2 SET 23 7.2 Event subscription and notification.24 7.2.1 Event subscription.24 7.2.2 Event notification .25 Annex A (normative) E CMA -400 E dition 1 R esour c e c onfigur ation options .26 Annex B (informative) R esour c e c onfigur ation of a CRAH s

12、y st em s fluid perspecti v e 30 ISO/IEC 2015 All rights reserved iiiBS ISO/IEC 19395:2015ISO/IEC 19395:2015(E) Foreword ISO (the International Organization for Standardization) and IEC (the International Electrotechnical Commission) form the specialized system for worldwide standardization. Nationa

13、l bodies that are members of ISO or IEC participate in the development of International Standards through technical committees established by the respective organization to deal with particular fields of technical activity. ISO and IEC technical committees collaborate in fields of mutual interest. O

14、ther international organizations, governmental and non-governmental, in liaison with ISO and IEC, also take part in the work. In the field of information technology, ISO and IEC have established a joint technical committee, ISO/IEC JTC 1. The procedures used to develop this document and those intend

15、ed for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of document should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.or

16、g/directives). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO and IEC shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document

17、 will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement. For an explanation on the meaning of ISO specific terms and ex

18、pressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information ISO/IEC 19395 was prepared by Ecma International (as ECMA-400) and was adopted, under a s

19、pecial “fast-track procedure”, by Joint Technical Committee ISO/IEC JTC 1, Information technology, in parallel with its approval by national bodies of ISO and IEC.iv ISO/IEC 2015 All rights reservedBS ISO/IEC 19395:2015ISO/IEC 19395:2015(E) Introduction Operation of data centres requires management

20、of storage, computation, communication, electrical energy and temperature to achieve the required quality of service and efficiency parameters. Often, however, the separate management of Information Technology (IT), electrical energy (or power) and cooling Resource islands yields a sub-optimal resul

21、t. This International Standard provides Messages that facilitate integrated or “smart” monitoring and control of Resources in those islands. The Messages are exchanged between the Management Function and Resources. The International Standard acknowledges that those Resources may be composed of other

22、 Resources (e.g. a rack may contain servers, ventilators, etc.). In addition, e.g. those servers may be viewed from their computing, energy consumption or dissipation aspects which this International Standard models as Resource Components and groups into IT, power and fluid Domains, respectively. IS

23、O/IEC 2015 All rights reserved vBS ISO/IEC 19395:2015BS ISO/IEC 19395:2015Information technology Sustainability for and by information technology Smart data centre resource monitoring and control 1 Scope In the Smart Data Centre, Management Functions monitor and control Resources. Resources model IT

24、 and facility equipment, systems and components in a data centre. To monitor and control the Resources Properties, Management Functions exchange command, response or event Messages with Resources, see Figure 1. Figure 1 Scope Resources are made up out of Resource Components which this second edition

25、 shares Properties with classes in Common Information Models (CIM). Messages refer to Resources and their Properties. Messages are encoded in XML and exchanged in HTTP primitives. Figure 1 illustrates the functionality that this second edition adds as described above. Figure 2 Functionality that sec

26、ond edition adds Management Function(s), Resources, IT & facility equipment, systems and components themselves are out of scope as illustrated in Figure 1, Figure 2 and Figure 3. Static information such as location, addressing of Resources and CPU models are out of scope as well. INTERNATIONAL ST AN

27、DARD ISO/IEC 19395:2015(E) ISO/IEC 2015 All rights reserved 1BS ISO/IEC 19395:2015ISO/IEC 19395:2015(E) Figure 3 detailed scope using CIM (UML Notation) 2 Conformance Conformant Management Functions monitor and control Properties (Clause 6) of Resources using Messages as specified in Clause 7. In re

28、sponse to the commands, conformant responses and events from Resources use the Messages as specified in Clause 7. Any of the Resource configurations specified in Annex A may optionally be implemented, in addition to any other configuration using any combination of Resources and Resource Components.

29、3 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. DMTF, “CIM Schema”, h t t

30、p :/d m t f . org/standards/cim DMTF DSP0004, “CIM Infrastructure Specification” DMTF DSP0200, “CIM Operations over HTTP” DMTF DSP1009, “Sensors Profile” DMTF DSP1011, “Physical Asset Profile”2 ISO/IEC 2015 All rights reservedBS ISO/IEC 19395:2015ISO/IEC 19395:2015(E) DMTF DSP1014, “Ethernet Port Pr

31、ofile” DMTF DSP1022, “CPU Profile” DMTF DSP1027, “Power State Management Profile” DMTF DSP1029, “OS Status Profile” DMTF DSP1033, “Profile Registration Profile” DMTF DSP1035, “Host LAN Network Port Profile” DMTF DSP1042, “System Virtualization Profile” DMTF DSP1044, “Processor Resource Virtualizatio

32、n Profile” DMTF DSP1045, “Memory Resource Virtualization Profile” DMTF DSP1047, “Storage Resource Virtualization Profile” DMTF DSP1052, “Computer System Profile” DMTF DSP1053, “Base Metrics Profile” DMTF DSP1057, “Virtual System Profile” DMTF DSP1081, “Virtual System Migration Profile” 4 T erms, d e

33、finitions and acr on yms For the purposes of this document, the following terms, definitions and acronyms apply. 4.1 Common Information Model CIM 4.2 CIM Client emitter of CIM message requests and consumer of CIM message responses 4.3 CIM Listener consumer of events 4.4 CIM message request command o

34、r event request 4.5 CIM message response response 4.6 condition query expression on property value ISO/IEC 2015 All rights reserved 3BS ISO/IEC 19395:2015ISO/IEC 19395:2015(E) 4.7 Distributed Management Task Force DMTF Note 1 to entry: DMTFs URL is http:/ /www.dmtf.org/ 4.8 domain set of resource co

35、mponents 4.9 e v e n t d e s c r i p t i o n i n d i c a t i o n f i l t e r set of conditions and associated parameters 4.10 Information Technology IT 4.11 CIM message command, response or event 4.12 Management Function MF 4.13 property resource attribute 4.14 Resource Component RC 4.15 CIM Resourc

36、e representation of IT and facility equipment, systems or components 4.16 Smart Data Centre SDC arrangement of all the resources and management function(s) 5 Domains 5.1 Introduction This International Standard specifies Resource Components (RC) which share Properties with CIM classes, to compose Re

37、source configurations as specified in Figure 3. The Resource Components are grouped into IT, power, fluid and base Domains.4 ISO/IEC 2015 All rights reservedBS ISO/IEC 19395:2015ISO/IEC 19395:2015(E) Figure 4 Resource and Resource Component In tables in this Clause, the Key indicates the identifier

38、which shall be unique in the SDC namespace as specified in Common Information Model (CIM) Infrastructure Specification (DSP0004). The Key uniquely identifies each instance. 5.2 Base Domain To construct the foundation of Resources, Resource Components from the base Domain shall be used. 5.2.1 CIM_Sys

39、tem See CIM Schema. 5.2.2 CIM_BaseMetricDefinition See Base Metrics Profile (DSP1053). TimeScope is optional in DSP1053 whereas in this International Standard, TimeScope is mandatory. 5.2.3 CIM_BaseMetricValue The requirements in Base Metrics Profile (DSP1053) and those in Table 1 apply. ISO/IEC 201

40、5 All rights reserved 5BS ISO/IEC 19395:2015ISO/IEC 19395:2015(E) Table 1 Class: CIM_BaseMetricValue Properties M/O *1 Requirements on Value TimeStamp Mandatory In case the device generating the metric instances does not have a clock device, the TimeStamp value shall be “99990101000000.000000+000” i

41、n case the base metric definition time scope requires that the TimeStamp value is not NULL. “99990101000000.000000+000” is used to indicate that the DateTime property value is not valid. Volatile Mandatory TRUE *1“M/O” indicates “mandatory or optional.” 5.2.4 CIM_MetricDefForME CIM_MetricDefForME sh

42、all be used to associate CIM_BaseMetricDefinition to SDC_ FluidMeasurementPoint. The requirements in Base Metrics Profile (DSP1053) and those in Table 2 apply. If the CIM_BaseMetricDefinition class is implemented, CIM_MetricDefForME shall be also implemented. Table 2 Class: CIM_MetricDefForME Proper

43、ties M/O Requirements on value Antecedent Mandatory Key: Shall be a reference to SDC_FluidMeasurementPoint with Cardinality 1 indicating one reference Dependent Mandatory Key: Shall be a reference to CIM_BaseMetricDefinition with Cardinality 1* indicating one or more references MetricCollectionEnabl

44、ed Optional 5.2.5 CIM_MetricInstance CIM_MetricInstance shall be used to associate CIM_BaseMetricValue instances to CIM_BaseMetricValue instances. See Base Metrics Profile (DSP1053). If the CIM_BaseMetricDefinition class is implemented, CIM_MetricInstance shall be also implemented. 5.2.6 CIM_R egist

45、 er edPr ofile The requirements in Profile Registration Profile (DSP1033) and those in Table 3 apply. T a b l e 3 C l a s s : C I M _ Re g i s t e r e d P r o f i l e Properties M/O Requirements on value RegisteredName Mandatory “CoolingSystem” RegisteredVersion Mandatory “1.0.0” RegisteredOrganizat

46、ion Mandatory 1 (Others) OtherRegisteredOrganization Mandatory “Ecma_TGG” 5.2.7 CIM_SystemDevice CIM_SystemDevice association shall be used to associate SDC_FluidElement with the CIM_System instance of which it is a member. The requirements in CIM Schema and those in Table 4 apply.6 ISO/IEC 2015 All

47、 rights reservedBS ISO/IEC 19395:2015ISO/IEC 19395:2015(E) Table 4 Class: CIM_SystemDevice Properties M/O Requirements on value Antecedent Mandatory Key: Shall be a reference to CIM_System with Cardinality 1 indicating one reference Dependent Mandatory Key: Shall be a reference to SDC_FluidElement w

48、ith Cardinality 1* indicating one or more references 5.2.8 CIM_Component CIM_Component association shall be used to associate SDC_FluidElement instances of which it is involved. The requirements in CIM Schema and those in Table 5 apply. Table 5 Class: CIM_Component Properties M/O Requirements on val

49、ue Antecedent Mandatory Key: Shall be a reference to SDC_FluidElement with Cardinality 1 indicating one reference Dependent Mandatory Key: Shall be a reference to SDC_FluidElement with Cardinality 1* indicating one or more references 5.2.9 Metrics for fluid measur ements The set of fluid metrics supported by an instance of SDC_FluidMeasurementPoint is implementation dependent. An instance of SDC_FluidMeasurementPoint may support all, none, or any combination of thes