BS ISO IEC 24735-2012 Information technology Office equipment Method for measuring digital copying productivity《信息技术 办公设备 数字复印产量的测量方法》.pdf

1、raising standards worldwide NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BSI Standards Publication BS ISO/IEC 24735:2012 Information technology Office equipment Method for measuring digital copying productivityBS ISO/IEC 24735:2012 BRITISH STANDARD National foreword This Br

2、itish Standard is the UK implementation of ISO/IEC 24735:2012. It supersedes BS ISO/IEC 24735:2009 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee IST/3, IT Printers and Cartridges. A list of organizations represented on this committee can be obtained

3、 on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2012. Published by BSI Standards Limited 2012 ISBN 978 0 580 73898 2 ICS 37.100.10 Compliance wi

4、th a British Standard cannot confer immunity from legal obligations. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 August 2012. Amendments issued since publication Date Text affectedBS ISO/IEC 24735:2012Reference number ISO/IEC 24735:201

5、2(E) ISO/IEC 2012INTERNATIONAL STANDARD ISO/IEC 24735 Second edition 2012-06-15Information technology Office equipment Method for measuring digital copying productivity Technologie de linformation quipements de bureau Mthode de mesure de la productivit dun photocopieur numrique BS ISO/IEC 24735:2012

6、 ISO/IEC 24735:2012(E) COPYRIGHT PROTECTED DOCUMENT ISO/IEC 2012 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from

7、either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO/IEC 2012 All rights reservedBS ISO/IEC 2473

8、5:2012 ISO/IEC 24735:2012(E) ISO/IEC 2012 All rights reserved iiiContents Page Foreword iv Introduction . v 1 Scope 1 2 Normative references 1 3 Terms and definitions . 1 4 Test Parameters and Conditions . 3 4.1 Environment . 3 4.2 Voltage 3 4.3 Copying Device Setup . 3 4.4 Paper . 4 4.5 Maintenance

9、 . 4 4.6 Preparation of Test Targets (Test Charts) 4 5 Test Method . 5 5.1 Test Setup 5 5.2 Test Measurement Procedure 5 5.3 Test Method Process 8 5.4 General Performance Test 10 5.5 Feature Performance Test 11 6 Calculations and Treatment of Data 14 6.1 General Performance Test 15 6.2 Feature Perfo

10、rmance Test 16 7 Presentation of Results 17 7.1 General Performance Test 17 7.2 Feature Performance Test 19 Annex A (informative) Examples of report presentation 20 Annex B (informative) Example of full detailed report 23 B.1 General . 23 B.2 Machine Setup Information and Pre-set items . 23 B.3 Meas

11、urement Results for General Performance Test . 24 B.4 Measurement Results for Feature Performance Test 24 B.5 Other special modes . 25 Annex C (normative) Test targets for measurement of copying productivity 26 Annex D (informative) Definitions of “FCOT” and “Continuous Copying Speed” . 27 Bibliogra

12、phy 30 BS ISO/IEC 24735:2012 ISO/IEC 24735:2012(E) iv ISO/IEC 2012 All rights reservedForeword ISO (the International Organization for Standardization) and IEC (the International Electrotechnical Commission) form the specialized system for worldwide standardization. National bodies that are members

13、of ISO or IEC participate in the development of International Standards through technical committees established by the respective organization to deal with particular fields of technical activity. ISO and IEC technical committees collaborate in fields of mutual interest. Other international organiz

14、ations, governmental and non-governmental, in liaison with ISO and IEC, also take part in the work. In the field of information technology, ISO and IEC have established a joint technical committee, ISO/IEC JTC 1. International Standards are drafted in accordance with the rules given in the ISO/IEC D

15、irectives, Part 2. The main task of the joint technical committee is to prepare International Standards. Draft International Standards adopted by the joint technical committee are circulated to national bodies for voting. Publication as an International Standard requires approval by at least 75 % of

16、 the national bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO and IEC shall not be held responsible for identifying any or all such patent rights. ISO/IEC 24735 was prepared by Joint Technical Committee

17、ISO/IEC JTC 1, Information technology, Subcommittee SC 28, Office equipment. This second edition cancels and replaces the first edition (ISO/IEC 24735:2009), which has been technically revised. It also incorporates the Technical Corrigendum ISO/IEC 24735:2009/Cor.1:2009. BS ISO/IEC 24735:2012 ISO/IE

18、C 24735:2012(E) ISO/IEC 2012 All rights reserved vIntroduction Many digital copying devices produce copied pages at a different rate than their nominal speed when running with different modes (simplex, duplex, copying quality modes), different substrate weight and collating and/or finishing options.

19、 The degree to which a reduction in productivity is experienced depends significantly on other parameters of the job stream. The most dominant of the parameters of the job stream are: the number of original pages in a set to be printed, whether ouput pages are single-sided or double-sided, image qua

20、lity modes selected, B&W and colour reproduction job stream, number of print sets to be produced, substrate size used, run length and finishing options. The existing International Standard (ISO/IEC 14545) only addresses the productivity issues for light-lens B&W copying device/duplicators and does n

21、ot take into account these important machine and job related factors for digital copying devices. BS ISO/IEC 24735:2012BS ISO/IEC 24735:2012 INTERNATIONAL STANDARD ISO/IEC 24735:2012(E) ISO/IEC 2012 All rights reserved 1Information technology Office equipment Method for measuring digital copying pro

22、ductivity 1 Scope This International Standard specifies a method for measuring the “productivity” of digital copying devices and multifunctional devices with various copying modes. It is applicable to digital copying devices and multifunctional devices equipped with automatic document feeder and col

23、lating function. This International Standard is intended to be used for black and white (B&W) as well as colour digital copying devices and multifunctional devices of any underlying marking technology. It allows comparison of the throughput copying rates for a machine operated in various available o

24、perating modes (simplex, duplex, size of substrates, 2-up, etc) and various available digital image processing configurations. This International Standard includes test files, test setup procedures, test procedures, and reporting requirements for digital copying productivity measurements. This Inter

25、national Standard is not intended to be used for devices which are not able to copy on a media size of A4/8.5“x11“, devices that do not have an automatic document feeder (ADF), or devices which are not able to collate multiple copies of original prints from a test set. This International Standard is

26、 not intended to replace manufacturers rated speeds. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (includin

27、g any amendments) applies. ISO 2470-1:2009, Paper, board and pulps Measurement of diffuse blue reflectance factor Part 1: Indoor daylight conditions (ISO brightness) ISO 536:1995, Paper and board Determination of grammage 3 Terms and definitions For the purposes of this document, the following terms

28、 and definitions apply. 3.1 duplex copying use of a copying device to make a number of copies with the copying being done on both sides of the sheet NOTE An equivalent term is “two-sided copying” and referred to as 1:2 mode or 2:2 mode. 3.2 effective throughput EFTP average speed at which a device p

29、roduces pages measured from the initiation of the job through the complete exit of the last page of the last test set BS ISO/IEC 24735:2012 ISO/IEC 24735:2012(E) 2 ISO/IEC 2012 All rights reservedNOTE EFTP is expressed in images per minute (ipm). EFTP can be affected by the digital processing time o

30、f the test set as well as the run time of the test set. 3.3 estimated saturated throughput ESAT rate at which a device produces pages measured from the complete exit of the last page of the first test set through the complete exit of the last page of the last test set NOTE ESAT is expressed in image

31、s per minute (ipm). 3.4 feature performance test optional test used to evaluate productivity changes with various copying and finishing features enabled by providing FSOT and ESAT NOTE The feature performance test suite is run with default copying system settings to establish a base line, and then w

32、ith the selected feature (e.g. stapling) ON, for comparison. 3.5 first set out time FSOT number of seconds between the initiation of the job to the complete exit of the last page of the first test set NOTE There is a different definition called “FCOT“ (first copy out time). “FCOT” and “continuous co

33、pying speed” for EP (electrophotographic) copying machines are defined in ISO/IEC 21117. For reference, the extension of these definitions, also applied for out of scope copying devices, is shown in Annex D (informative). 3.6 full detailed report presentation of information including machine setup a

34、nd measured test results 3.7 full report presentation of results including the FSOT, ESAT and EFTP values in general performance tests or the FSOT and ESAT values in feature performance tests as well as the calculated averages for each value 3.8 general performance test test used to evaluate product

35、ivity by providing FSOT, ESAT and EFTP without using any special feature or mode, and which includes both the simplex copying mode and the duplex copying modes 1:2 and 2:2, if available 3.9 last set out time LSOT number of seconds between the initiation of the job to the complete exit of the last pa

36、ge of the last test set 3.10 nominal copying speed copying rate, excluding time to first page copied, measured when producing pages in a continuous copying mode with a single static document using a nominal weight substrate NOTE Nominal copying speed is expressed in copies per minute or images per m

37、inute. 3.11 simplex copying use of a copying device when only a single side of a sheet is copied on NOTE Other equivalent terms are “one-sided copying” or “simplex to simplex” referred to as 1:1 mode. BS ISO/IEC 24735:2012 ISO/IEC 24735:2012(E) ISO/IEC 2012 All rights reserved 33.12 summary report p

38、resentation of results, including the average overall FSOT and ESAT in general performance tests or the ratio of the copying performance such as FSOT and ESAT with the subject feature ON versus the copying device default base line performance (without the subject feature ON) in feature performance t

39、ests 3.13 test file digital file used for creating test targets 3.14 test set all of the pages of a test target 3.15 test target hard copy document used for testing per the test method, and created from a test file NOTE An equivalent term is “test chart”. 4 Test Parameters and Conditions 4.1 Environ

40、ment The test environment, including temperature and humidity, shall be within the ranges recommended by the manufacturer for operating the device. If no recommendation is available, the following ranges shall apply. Temperature: 18 C to 25 C Relative humidity: 30% to 70% NOTE The temperature and hu

41、midity of the test environment should be recorded in the full detailed report (Annex B). 4.2 Voltage The copying device shall be connected to a voltage supply within the manufacturer specified operating voltage range for the copying device under test. NOTE The measurement should be made under no-loa

42、d condition prior to each test. 4.3 Copying Device Setup Place the copying device on a horizontal surface and set up the copying device according to the manufacturers recommendations. The copying device shall be fully enclosed in its normal exterior cover. The machine and all of its necessary suppli

43、es shall be acclimated in the test environment prior to conducting the test(s) at least 8 hours. All supplies used in the test(s), included copy paper, shall be those specified by the manufacturer. All image and copying modes should be at their factory pre-set configuration for the copying device. I

44、t is assumed that the settings listed in Table 1 are common to all copying devices. These listed settings shall be set to the manufacturers default or pre-set condition for the device. If a device has settings not listed in Table 1, they too shall be set to default settings. For copying devices that

45、 have additional print quality and digital image processing features, those features must be set to match their normal default condition, and included in the result reporting. Disabling manufacturer default installed features, routines or applications, is not allowed. Examples include, but are not l

46、imited to the following: automatic cleaning or calibration cycles, and energy save settings. If the system has automatic media detect(automatic paper type selection), it can be disabled, and paper used in the test shall be selected manually. This must be noted in the full detailed report (Annex B).

47、The following pre-set values in the test will be noted on this report format. BS ISO/IEC 24735:2012 ISO/IEC 24735:2012(E) 4 ISO/IEC 2012 All rights reservedIf the copying device is setup with internal or external options such as memory, sorter, or finisher as default, then these options shall be not

48、ed on the full detailed report format in the configuration options as shown in Annex B, for example “Finisher as default” or “160GB HDD installed”. Table 1 Pre-set Settings Pre-set item Pre-set value Mode Output resolution default Output Quality default Copying mode default Auto density adjustment d

49、efault Collating function Activated (if not activated in default mode.) Paper Paper sending direction default Paper type setting default Paper-path Paper feeding Standard cassette Paper exit Standard exit tray Face up exit default Duplex copying unit default (used in 1:2 mode and 2:2 mode). Temporary stop Fixing capability default Image quality stability default Capacity of paper default Others default 4.4 Paper The output paper used in this test shall be within the range of, and/or not violate, specific written attr