BS ISO IEC 29102-2015 Information technology Office equipment Method for the determination of ink cartridge photo yield for colour printing with inkjet printers and multi-.pdf

1、BSI Standards Publication BS ISO/IEC 29102:2015 Information technology Office equipment Method for the determination of ink cartridge photo yield for colour printing with inkjet printers and multi-function devices that contain inkjet printer componentsBS ISO/IEC 29102:2015 BRITISH STANDARD National

2、foreword This British Standard is the UK implementation of ISO/IEC 29102:2015. It supersedes BS ISO/IEC 29102:2011 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee IST/3, IT Printers and Cartridges. A list of organizations represented on this committee

3、 can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2015. Published by BSI Standards Limited 2015 ISBN 978 0 580 84355 6 ICS 37.100.

4、10 Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 August 2015. Amendments issued since publication Date Text affectedBS ISO/IEC 29102:2015 Information techn

5、ology Office equipment Method for the determination of ink cartridge photo yield for colour printing with inkjet printers and multi-function devices that contain inkjet printer components Technologies de linformation quipement de bureau Mthode dessai de la dtermination du rendement des cartouches de

6、ncre pour limpression de photographies en couleurs avec des imprimantes jet dencre et des dispositifs multi-fonctions contenant des composants dimprimantes jet dencre INTERNATIONAL STANDARD ISO/IEC 29102 Reference number ISO/IEC 29102:2015(E) Second edition 2015-08-15 ISO/IEC 2015 BS ISO/IEC 29102:2

7、015ii ISO/IEC 2015 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO/IEC 2015, Published in Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopyin

8、g, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Ch. de Blandonnet 8 CP 401 CH-1214 Vernier, Geneva, Switzerland Tel. +41 22 749 0

9、1 11 Fax +41 22 749 09 47 copyrightiso.org www.iso.org ISO/IEC 29102:2015(E)BS ISO/IEC 29102:2015ISO/IEC 29102:2015(E)Foreword iv Introduction v 1 Scope . 1 2 Normative references 1 3 Terms and definitions . 2 4 Test parameters and conditions . 4 4.1 Set up . 4 4.2 Sample size . 5 4.3 Print mode 5 4

10、.4 Print environment 6 4.5 Paper 7 4.6 Maintenance 7 4.7 Test files 7 5 Test methodology 8 5.1 Testing procedure . 8 5.1.1 Preparation . 8 5.1.2 Installation of test cartridges 8 5.1.3 Testing . 8 5.1.4 End of cartridge life procedure . 8 5.2 Procedure for handling streaks 8 5.2.1 General 8 5.2.2 No

11、zzle cleaning . 9 5.3 Procedure for handling a defective cartridge, printhead or printer . 9 5.3.1 General 9 5.3.2 Defective cartridge 10 5.3.3 Defective printhead 10 5.3.4 Defective printer .10 6 Determination of the declared yield value and declaration 10 6.1 Yield of primary cartridges .10 6.2 Yi

12、eld of supplemental cartridges .11 6.2.1 General.11 6.2.2 Case 1: supplemental cartridges that has not reached End of life .12 6.2.3 Case 2: supplemental cartridges that have reached End of life once or twice 13 6.3 Test data reporting .15 6.4 Declaration of the yield .15 Annex A (informative) Examp

13、les of fade .19 Annex B (informative) Examples of streaks .20 Annex C (normative) Test reporting form 21 Annex D (informative) Process flowchart.24 Annex E (informative) Method for black and white photo yield determination 26 ISO/IEC 2015 All rights reserved iii Contents PageBS ISO/IEC 29102:2015ISO

14、/IEC 29102:2015(E) Foreword ISO (the International Organization for Standardization) and IEC (the International Electrotechnical Commission) form the specialized system for worldwide standardization. National bodies that are members of ISO or IEC participate in the development of International Stand

15、ards through technical committees established by the respective organization to deal with particular fields of technical activity. ISO and IEC technical committees collaborate in fields of mutual interest. Other international organizations, governmental and non-governmental, in liaison with ISO and

16、IEC, also take part in the work. In the field of information technology, ISO and IEC have established a joint technical committee, ISO/IEC JTC 1. The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular

17、 the different approval criteria needed for the different types of document should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements of this docume

18、nt may be the subject of patent rights. ISO and IEC shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.

19、iso.org/patents). Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement. For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to th

20、e WTO principles in the Technical Barriers to Trade (TBT), see the following URL: Foreword Supplementary information. The committee responsible for this document is ISO/IEC JTC 1, Information technology, Subcommittee SC 28, Office equipment. This second edition cancels and replaces the first edition

21、 (ISO/IEC 29102:2011), of which it constitutes a minor revision.iv ISO/IEC 2015 All rights reservedBS ISO/IEC 29102:2015ISO/IEC 29102:2015(E) Introduction The scope of this International Standard is limited to evaluation of ink cartridge photo yield of ink- containing cartridges (i.e. integrated ink

22、 cartridges and ink cartridges without integrated printheads) for colour photo printing with colour inkjet printers. This International Standard can be applied to colour inkjet printers having an interface to a computer as well as colour inkjet printers that cannot be connected to a computer. This I

23、nternational Standard can also be applied to the inkjet printer component of any multifunctional device that has a digital input printing path, including multi-function devices that contain inkjet printer components. Both liquid and solid ink products can be tested using this International Standard.

24、 The cartridge photo yields of primary cartridges are determined by an end of life judgment, or signalled with either of two phenomena: fade, caused by depletion of ink in the cartridge, or automatic printing stop, caused by an Ink Out detection function. The cartridge photo yields of supplemental c

25、artridges are estimated. It is envisioned that one of the uses of this International Standard will be for the calculation of cost per page (CPP). While this International Standard measures a portion of this cost, it is not used as the sole component of CPP calculation. Additional factors need to be

26、considered for accurate CPP calculations. ISO/IEC 2015 All rights reserved vBS ISO/IEC 29102:2015BS ISO/IEC 29102:2015Information technology Office equipment Method for the determination of ink cartridge photo yield for colour printing with inkjet printers and multi-function devices that contain ink

27、jet printer components 1 Scope The purpose of this International Standard is to provide a method to determine the ink cartridge photo yield of ink-containing cartridges (i.e. integrated ink cartridges and ink cartridges without integrated printheads) for colour photo printing with colour inkjet prin

28、ters and multifunction devices that contain inkjet printer components. In the case where a cartridge set can be used in multiple printer models, only one yield test needs to be performed as long as the difference between printer models does not impact yield. NOTE A cartridge supplier may choose to u

29、se more than one market identifier for a single physical cartridge. In this case only one yield test is required as long as there are no differences in the cartridges other than market identifiers. This International Standard prescribes the following: the test method that manufacturers, test laborat

30、ories, etc. use to determine ink cartridge photo yield; the method for determination of declared photo yield values from the test results; and the appropriate method of describing the photo yield of cartridges in documentation supplied to the consumer by the manufacturer. This International Standard

31、 is only intended for the determination of ink cartridge photo yield. No other claims can be made from this testing regarding quality, reliability, etc. This International Standard can be used to determine the yield of any cartridge that is used during the printing of the photo test file defined in

32、ISO/IEC 29103. This International Standard is not for use with printers whose minimum printable size is equal to or greater than A3. This International Standard is not intended to measure the yield of photo printing on paper size larger than 46, L or A6. In addition, this International Standard is n

33、ot for use with industrial printers or point of sale printers. It only applies to desktop printing systems. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the editi

34、on cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO/IEC 29103, Information technology Office equipment Colour photo test pages for measurement of ink cartridge yield for colour photo printing ISO/IEC 24711, Method for the de

35、termination of ink cartridge yield for colour inkjet printers and multi- function devices that contain printer components INTERNATIONAL ST ANDARD ISO/IEC 29102:2015(E) ISO/IEC 2015 All rights reserved 1BS ISO/IEC 29102:2015ISO/IEC 29102:2015(E) 3 Terms and definitions For the purposes of this docume

36、nt, the following terms and definitions apply. 3.1 fade phenomenon in which a significant colour change occurs due to ink depletion Note 1 to entry: If a printer exhibits fade, a five minute pause is allowed to provide for recovery of the ink delivery system and printing can continue. If fade appear

37、s on the next page, then the cartridge is judged at end of life and the additional page printed after the five minute pause is not counted in the yield calculation. If fade does not appear on the next page, then printing can continue until the next fade or ink out is encountered. Note 2 to entry: Fo

38、r examples of fade, please consult Annex A. Note 3 to entry: In some printer systems, fade can occur prematurely due to the way that ink is provided to the printing system. Note 4 to entry: It can be helpful to use the first photo test suite print samples from the first cartridge set for colour comp

39、arison. Note 5 to entry: A blue light source (such as a blue LED) can be used to help in the detection of yellow fade. 3.2 streak thin lines of colour that appear in test images Note 1 to entry: Streaks differ from fade in the width. Note 2 to entry: If streaks occur in two or more out of four conse

40、cutive test pages, then a streak removal operation is required. Note 3 to entry: Streaks can appear due to a number of reasons; thermal issues and clogged nozzles being two of the main causes. Comparisons are made using the phenomenon sample provided in Annex B. 3.3 streak removal operation procedur

41、e used to restore the print performance by removing streaks Note 1 to entry: It is often called a nozzle cleaning operation. Note 2 to entry: If streaks are observed in two or more out of four consecutive test pages, first the printer can be left idle for five minutes. Then an additional four pages

42、are printed. If the streaks are still observed, then a streak removal operation is conducted according to the latest printer manufacturer documentation. Due to the significant amount of ink that is used for cleaning, the maximum permissible number of times that the streak removal operation can be us

43、ed on a given cartridge is prescribed in 5.2.1. All test pages printed during this process will be included in the page count for determining the yield. 3.4 printhead alignment operation function that aligns newly installed printheads Note 1 to entry: If it is mandatory according to the latest print

44、er manufacturer documentation, this operation is performed during testing. The pages used in the alignment procedure are not counted in the measurement of yield. 3.5 ink low warning generated by the printing system when it has determined that the amount of ink is such that a cartridge change may be

45、required soon Note 1 to entry: It does not indicate that the system is out of ink.2 ISO/IEC 2015 All rights reservedBS ISO/IEC 29102:2015ISO/IEC 29102:2015(E) 3.6 ink out signal generated by the printing system when the usable ink in the system is depleted and the printer stops printing 3.7 end of l

46、ife condition determined by one of two mechanisms: fade (3.1) or ink out (3.6) Note 1 to entry: For cartridges containing multiple colour inks, end of life is defined when the first colour exhibits fade or ink out. In the event that the printer can continue printing after ink out is reported, the ca

47、rtridge will still be considered at end of life. 3.8 end of testing point of time when all of primary cartridges are consumed three times per printer under testing 3.9 photo test suite series of pages defined in ISO/IEC 29103 that are printed as separate jobs 3.10 individual cartridge photo yield nu

48、mber of pages printed between cartridge installation and end of life 3.11 declared cartridge photo yield at or below the lower 90 % confidence bound of the mean Note 1 to entry: 90 % confidence bound of the mean is prescribed in 6.1 and 6.2. 3.12 primary cartridge major contributing cartridge for in

49、k consumption Note 1 to entry: The minimum number of primary cartridges to be tested for different printing systems is prescribed in 4.2. Cartridges that reach end of life (3.7) first are classified as primary cartridges. They should be consumed at least three times per printer at end of testing (3.8). Note 2 to entry: Colour inkjet printers commonly utilize a set of different colour inks to improve quality of photo images. The number of different colour inks ranges from three to