BS ISO IEC 29142-1-2013 Information technology Print cartridge characterization General terms symbols notations and cartridge characterization framework《信息技术 打印盒特性描述 总论 术.pdf

1、BSI Standards Publication BS ISO/IEC 29142-1:2013 Information technology Print cartridge characterization Part 1: General: terms, symbols, notations and cartridge characterization frameworkBS ISO/IEC 29142-1:2013 BRITISH STANDARD National foreword This British Standard is the UK implementation of IS

2、O/IEC 29142-1:2013. The UK participation in its preparation was entrusted to Technical Committee IST/3, IT Printers and Cartridges. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provis

3、ions of a contract. Users are responsible for its correct application. The British Standards Institution 2013. Published by BSI Standards Limited 2013 ISBN 978 0 580 77892 6 ICS 37.100.10 Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was publ

4、ished under the authority of the Standards Policy and Strategy Committee on 31 July 2013. Amendments issued since publication Date Text affectedBS ISO/IEC 29142-1:2013 Information technology Print cartridge characterization Part 1: General: terms, symbols, notations and cartridge characterization fr

5、amework Technologies de linformation Caractrisation de cartouche dimpression Partie 1: Gnralits: termes, symboles, notations et cadre de travail de caractrisation de cartouche ISO/IEC 2013 INTERNATIONAL STANDARD ISO/IEC 29142-1 First edition 2013-04-01 Reference number ISO/IEC 29142-1:2013(E)BS ISO/

6、IEC 29142-1:2013ISO/IEC 29142-1:2013(E)ii ISO/IEC 2013 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO/IEC 2013 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including p

7、hotocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 74

8、9 09 47 E-mail copyrightiso.org Web www.iso.org Published in SwitzerlandBS ISO/IEC 29142-1:2013ISO/IEC 29142-1:2013(E) ISO/IEC 2013 All rights reserved iii Contents Page Foreword iv Introduction v 1 Scope . 1 2 Normative references 1 3 T erms and definitions . 1 4 Requirements 7 5 Structure of ISO/I

9、EC 29142 . 8 5.1 Data Reporting 8 5.2 Environmental . 8 5.3 Toner and ink cartridge characterization 9 6 Framework Overview for cartridge characterization 9 6.1 Elements of a print system . 9 6.2 Cartridge configurations10 6.3 Performance attributes measured on a printed page 10 6.4 Physical attribu

10、tes 11 7 Attribute framework for testing and characterizing cartridges 11 7.1 Overview .11 7.2 Special considerations for binomial and continuous performance point attributes 13 7.3 Special considerations for point and lifetime binomial attributes13 7.4 Special considerations for performance testing

11、 with page attribute values 13 7.5 Test requirements for all attributes .15 7.6 Test methodology for lifetime and point attributes .19 8 Framework requirements for determination of declared attribute values .22 8.1 Determination of the declared value for continuous lifetime or continuous physical at

12、tributes.22 8.2 Determination of the declared value for continuous point attributes .23 8.3 Determination of the declared value for lifetime, point and physical binomial attributes 24 9 Framework requirements for reporting cartridge characterization results .24 Annex A (informative) Terms cross-refe

13、rence 25 Bibliography .28BS ISO/IEC 29142-1:2013ISO/IEC 29142-1:2013(E) Foreword ISO (the International Organization for Standardization) and IEC (the International Electrotechnical Commission) form the specialized system for worldwide standardization. National bodies that are members of ISO or IEC

14、participate in the development of International Standards through technical committees established by the respective organization to deal with particular fields of technical activity. ISO and IEC technical committees collaborate in fields of mutual interest. Other international organizations, govern

15、mental and non-governmental, in liaison with ISO and IEC, also take part in the work. In the field of information technology, ISO and IEC have established a joint technical committee, ISO/IEC JTC 1. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Par

16、t 2. The main task of the joint technical committee is to prepare International Standards. Draft International Standards adopted by the joint technical committee are circulated to national bodies for voting. Publication as an International Standard requires approval by at least 75 % of the national

17、bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO and IEC shall not be held responsible for identifying any or all such patent rights. ISO/IEC 29142-1 was prepared by Joint Technical Committee ISO/IEC JTC

18、1, Information technology, Subcommittee SC 28, Office equipment.iv ISO/IEC 2013 All rights reservedBS ISO/IEC 29142-1:2013ISO/IEC 29142-1:2013(E) Introduction The purpose of this part of ISO/IEC 29142 is to define the framework for characterizing ink and toner cartridges used in printing devices tha

19、t have a digital input printing path, including multi-function devices. This part of ISO/IEC 29142 defines terms, symbols, and notations used throughout the ISO/IEC 29142 series to characterize such ink and toner cartridges. Customer information related to ink and toner cartridges is not consistent

20、in the global marketplace. Cartridge manufacturers, including original, non-original manufacturers, refillers, and remanufacturers, have each communicated expressions of cartridge characteristics. The ISO/IEC 29142 series is provided to aid transparency between manufacturers, suppliers and their cus

21、tomers regarding selected cartridge characteristics. The selected cartridge characteristics do not provide for an exhaustive cartridge characterization. Where applicable, cartridge attributes and the associated characterization tests are used consistently with both ink and toner cartridge technologi

22、es. The selected cartridge attributes are defined for all cartridges, regardless of manufacturing methodology. ISO/IEC 2013 All rights reserved vBS ISO/IEC 29142-1:2013BS ISO/IEC 29142-1:2013Information technology Print cartridge characterization Part 1: General: terms, symbols, notations and cartri

23、dge characterization framework 1 Scope This part of ISO/IEC 29142 establishes terms, symbols, notations and a framework for characterizing toner and ink cartridges used in printing devices that have a digital input printing path, including multi- function devices. This part of ISO/IEC 29142 is inten

24、ded for equipment used in office environments. It primarily provides a foundation for measuring, evaluating, or specifying characteristics of such toner and ink cartridges. The terms, symbols, notations and framework established herein can be applied to such cartridges. The characterizations associa

25、ted with the terms, symbols, notations, and framework established herein are specified throughout the ISO/IEC 29142 series. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references

26、, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 13655, Graphic technology Spectral measurement and colorimetric computation for graphic arts images ISO 5-3, Photography and graphic technology Density meas

27、urements Part 3: Spectral conditions ISO/IEC 29142-2, Information technology Print cartridge characterization Part 2: Cartridge characterization data reporting ISO/IEC 29142-3, Information technology Print cartridge characterization Part 3: Environment 3 T erms a nd definiti ons For the purposes of

28、this document, the following terms and definitions apply. 3.1 all-in-one toner cartridge cartridge that includes at least: a toner containment part, a photoreceptor part, and a developer part 3.2 black-only printer printer with an operating part to apply ink or toner on a substrate with functionalit

29、y limited to print output using only a single black colourant Note 1 to entry: In the case of a printer capable to operate with only a black colourant cartridge and alternatively to operate with other cartridge configurations that include other colourants, the black-only printer condition is limited

30、 to when only the single black colourant cartridge is installed. INTERNATIONAL ST ANDARD ISO/IEC 29142-1:2013(E) ISO/IEC 2013 All rights reserved 1BS ISO/IEC 29142-1:2013ISO/IEC 29142-1:2013(E) 3.3 binomial attribute attribute which either occurs or does not occur and which is characterized by a cou

31、nt of the number of times it occurs in a particular number of observations Note 1 to entry: A random process is said to be binomial if it satisfies four basic properties: a) It consists of a sequence of n trials for some n 1. b) Each trial has exactly two possible outcomes, A and B, which are mutual

32、ly exclusive. c) P(A), the probability of A, takes the same value p on all n trials. P(B) is likewise fixed at 1-p. d) The n trials are independent of one another. 3.4 cartridge user replaceable unit operating with a printing system that includes at least a containing mechanism designed for material

33、s intended for deposition on a substrate 3.5 cartridge attribute test report report including the information of a cartridge customer report and the detailed cartridge characterization results of an ISO/IEC 29142 cartridge characterization test reported for customer presentation according to a requi

34、red format Note 1 to entry: The format is prescribed according to each ISO/IEC 29142 standardized or specified cartridge characterization test and is in compliance with ISO/IEC 29142-2. 3.6 cartridge characterization test test method provided in or in compliance with ISO/IEC 29142-1 for the purpose

35、of evaluating an attribute of a cartridge or cartridge set of interest to cartridge and cartridge set users 3.7 cartridge collector any party providing a cartridge take-back or collection program EXAMPLE A business entity designated to collect cartridges. 3.8 cartridge element sub piece of a cartrid

36、ge other than the containment part of the cartridge 3.9 cartridge end-of-life point in a cartridge life-cycle from which the cartridge is no longer used for its intended purpose without additional non-customer interaction 3.10 c a r t r id g e ident i f ie r formatted human readable arrangement of i

37、nformation uniquely specifying a distinct cartridge 3.11 cartridge life percent completion point point in the life of a cartridge computed as a percent of expected cartridge life 3.12 cartridge set group of colourants and their assignment to one or more cartridges as defined by a printer manufacture

38、r to be necessary and sufficient to produce the fully functional default colour renditions EXAMPLE Default colour renditions: printed black, red, green, blue, cyan, magenta, and yellow.2 ISO/IEC 2013 All rights reservedBS ISO/IEC 29142-1:2013ISO/IEC 29142-1:2013(E) Note 1 to entry: A printer may hav

39、e more than one fully functional cartridge set. 3.13 cartridge supplier cartridge marketer, manufacturer, remanufacturer, refiller, or distributor, being the party or parties responsible for marketing the cartridge and providing customer support for the cartridge 3.14 colour printer printer with an

40、operating part to apply ink or toner on a substrate, with functionality to produce print output containing colours 3.15 containment part containing mechanism designed for materials intended for deposition on a substrate 3.16 continuous attribute attribute which can take on any of a range of values 3

41、.17 cross-systems attribute tolerance range CSATR range of actual attribute values for a cartridge characterization attribute of a particular cartridge characterization test method, determined from evaluation of exemplary systems to which the test method applies 3.18 customer report report, includin

42、g a cartridge notification, and a cartridge attribute checklist, with summary results of selected ISO/IEC 29142 cartridge attribute characterization tests, presented according to a required format Note 1 to entry: The format is prescribed according to each ISO/IEC 29142 standardized or specified car

43、tridge characterization test and is in compliance with ISO/IEC 29142-2. 3.19 deposition material material, ink or toner, liquid or solid, colourant or non-colourant, that can be contained in a cartridge, and that is designed for deposition on a surface by means of a printing system 3.20 developer pa

44、rt physical mechanism, which may or may not be a cartridge element, which functions to apply toner particles to the latent image on the photoreceptor part of an electrophotographic printing system 3.21 discrete attribute attribute which can take only a finite number of values within a range, such as

45、 an integer count 3.22 dye ink material designed for liquid state deposition on a substrate, including a chemical dye colourant 3.23 electrophotographic printer printer principally using opto electric phenomena and electrost atic at traction to move toner to a substrate 3.24 end-of-life phase in a c

46、artridge life-cycle when the cartridge can no longer be used for its intended purpose without additional non-customer interaction ISO/IEC 2013 All rights reserved 3BS ISO/IEC 29142-1:2013ISO/IEC 29142-1:2013(E) 3.25 expected cartridge life approximate number of pages likely to be printed from a cart

47、ridge when run to cartridge end-of-life according to an ISO/IEC 29142 standardized or specified test method 3.26 f ill ed c ar t r i dg e user replaceable unit of a printing system that includes at least ink or toner materials, intended for deposition on a substrate and a containing mechanism for su

48、ch materials 3.27 incineration disposal method that involves combustion of waste material converting it into heat, gas, steam and ash but not including smelting 3.28 ink material, which may or may not include colourant, designed for liquid state deposition on a substrate 3.29 ink cartridge user repl

49、aceable unit of a printing system that includes at least a containing mechanism designed for ink intended for deposition on a substrate 3.30 ink deposition mechanism imaging apparatus for depositing ink on a printing substrate EXAMPLE A printhead. 3.31 ink transport part ink channelling mechanism operating between an ink deposition mechanism and an ink containment part, particularly when the ink deposition mechanism and the ink containment part are not physically abutted 3.32 inkjet printer printer with an operating part, fo