BS ISO IEC 29142-3-2013 Information technology Print cartridge characterization Environment《信息技术 打印盒特性描述 环境》.pdf

1、raising standards worldwide NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BSI Standards Publication BS ISO/IEC 29142-3:2013 Information technology Print cartridge characterization Part 3: EnvironmentBS ISO/IEC 29142-3:2013 BRITISH STANDARD National foreword This British Stan

2、dard is the UK implementation of ISO/IEC 29142-3:2013. The UK participation in its preparation was entrusted to Technical Committee IST/3, IT Printers and Cartridges. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport

3、to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2013. Published by BSI Standards Limited 2013 ISBN 978 0 580 74571 3 ICS 37.100.10 Compliance with a British Standard cannot confer immunity from legal obligati

4、ons. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 April 2013. Amendments issued since publication Date Text affectedBS ISO/IEC 29142-3:2013Reference number ISO/IEC 29142-3:2013(E) ISO/IEC 2013INTERNATIONAL STANDARD ISO/IEC 29142-3 First

5、 edition 2013-03-01 Information technology Print cartridge characterization Part 3: Environment Technologies de linformation Caractrisation de cartouche dimpression Partie 3: Environnement BS ISO/IEC 29142-3:2013 ISO/IEC 29142-3:2013(E) COPYRIGHT PROTECTED DOCUMENT ISO/IEC 2013 All rights reserved.

6、Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. I

7、SO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO/IEC 2013 All rights reservedBS ISO/IEC 29142-3:2013 ISO/IEC 29142-3:2013(E) ISO/IEC 2013 All rights reserved iiiContents Page For

8、eword iv Introduction . v 1 Scope 1 2 Normative references 1 3 Terms and definitions . 2 4 Abbreviated terms . 5 5 Relationship with ISO 14020 Series . 5 6 Company environmental responsibility 5 7 Environmental attributes throughout the cartridge life-cycle 5 8 Verification methods . 9 9 Life-cycle

9、assessment 10 10 Certification and compliance . 10 11 Mutual recognition 10 Bibliography 11 BS ISO/IEC 29142-3:2013 ISO/IEC 29142-3:2013(E) iv ISO/IEC 2013 All rights reservedForeword ISO (the International Organization for Standardization) and IEC (the International Electrotechnical Commission) for

10、m the specialized system for worldwide standardization. National bodies that are members of ISO or IEC participate in the development of International Standards through technical committees established by the respective organization to deal with particular fields of technical activity. ISO and IEC t

11、echnical committees collaborate in fields of mutual interest. Other international organizations, governmental and non-governmental, in liaison with ISO and IEC, also take part in the work. In the field of information technology, ISO and IEC have established a joint technical committee, ISO/IEC JTC 1

12、. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of the joint technical committee is to prepare International Standards. Draft International Standards adopted by the joint technical committee are circulated to national bodies f

13、or voting. Publication as an International Standard requires approval by at least 75 % of the national bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO and IEC shall not be held responsible for identifyin

14、g any or all such patent rights. ISO/IEC 29142-3 was prepared by Joint Technical Committee ISO/IEC JTC 1, Information technology, Subcommittee SC 28, Office equipment. ISO/IEC 29142 consists of the following parts, under the general title Information technology Print cartridge characterization: Part

15、 3: Environment The following parts are under preparation: Part 1: General: terms, symbols, notations and cartridge characterization framework Part 2: Cartridge Characterization Data Reporting BS ISO/IEC 29142-3:2013 ISO/IEC 29142-3:2013(E) ISO/IEC 2013 All rights reserved vIntroduction The purpose

16、of this part of ISO/IEC 29142 is to establish principles and framework for environmental product standards, environmental labels, and green procurement criteria specific to ink and toner cartridges used in printing devices that have a digital input printing path, including multi-function devices. Th

17、is standard includes terminology definitions for such cartridges and their environmental interactions, cartridge environmental attributes, and test methods for inclusion in cartridge environmental standards, environmental labels, and green procurement criteria. Printing systems use consumables and b

18、ecause of this, environmental responsibility is important to be considered during the phases of design, manufacturing, printer operation and end-of-life. The terms, definitions, attributes, and test methods established in this standard are generally applicable to all cartridges and are intended for

19、use in the development of environmental standards, environmental labels, and green procurement guidelines. The defined attributes and methods form a framework to standardize the treatment and definition of cartridge environmental issues. The foundation provided in this standard supports the followin

20、g objectives: 1. Minimization of product environmental impact throughout the cartridge life-cycle 2. Minimization of product environmental impact associated with end-of-life In an attempt to harmonize with existing environmental labels, standards, declarations, and green procurement criteria, enviro

21、nmental provisions and measurement methods already well established will be referenced wherever possible. This includes consideration of legal requirements and customer expectations associated with material use, manufacturing operations, and packaging, and/or management during end-of- life. This par

22、t of ISO/IEC 29142 provides the following: 1. Terms and definitions related to cartridge environmental attributes. 2. Cartridge environmental attributes for inclusion in environmental labels, standards and green procurement criteria. 3. Test methods that manufacturers, test labs, etc., use to determ

23、ine values for the defined cartridge environmental attributes. 4. Methods for determination of declared values from the test results. 5. Methods for declaration of conformance to provisions that dont require measurement. This International Standard is intended for office equipment environments. BS I

24、SO/IEC 29142-3:2013BS ISO/IEC 29142-3:2013 INTERNATIONAL STANDARD ISO/IEC 29142-3:2013(E) ISO/IEC 2013 All rights reserved 1Information technology Print cartridge characterization Part 3: Environment 1 Scope This part of ISO/IEC 29142 describes the principles and framework for environmental assessme

25、nt of ink and toner cartridges used in printing devices that have a digital input printing path, including multi-function devices, including: a) the goals and definitions related to environmental responsibility; b) guidance to determine the relative benefits of reuse, recycling, recovery, and reduct

26、ion techniques; c) identification and prioritization of environmental attributes according to each phase of the cartridge life- cycle; d) criteria for establishing environmentally sustainable practices. This part of ISO/IEC 29142 establishes foundational terms, definitions, attributes, and test meth

27、ods for cartridge environmental standards, environmental labels, and green procurement criteria. This part of ISO/IEC 29142 standardizes treatment of environmental interactions and impacts throughout the cartridge life-cycle, and promotes harmonization of environmental standards, environmental label

28、s, and green procurement criteria pertaining to ink and toner cartridges, thereby reducing impact on the environment and informing and benefiting the cartridge customer. This part of ISO/IEC 29142 establishes environmental terms, definitions, attributes and test methods in accordance with the terms,

29、 symbols, notations and framework of ISO/IEC 29142-1 and ISO Guide 64. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced

30、document (including any amendments) applies. ISO 1043 (all parts), Plastics Symbols and abbreviated terms ISO 11014, Safety data sheet for chemical products Content and order of sections ISO 11469, Plastics Generic identification and marking of plastic products ISO 14020, Environmental labels and de

31、clarations General principles ISO 14021, Environmental labels and declarations Self-declared environmental claims (Type II environmental labelling) BS ISO/IEC 29142-3:2013 ISO/IEC 29142-3:2013(E) 2 ISO/IEC 2013 All rights reservedISO 14024, Environmental labels and declarations Type I environmental

32、labelling Principles and procedures ISO 17025, General requirements for the competence of testing and calibration laboratories ISO/IEC 28360, Information Technology Office Equipment Determination of chemical emission rates from electronic equipment ISO/IEC 29142-1, Information technology Cartridge C

33、haracterization Part 1: General: terms, symbols, notations and cartridge characterization framework ISO/IEC 29142-2, Information technology Cartridge Characterization Part 2: Cartridge characterization data reporting 3 Terms and definitions For the purposes of this document, the terms and definition

34、s given in ISO/IEC 29142-1 and the following apply. 3.1 Ames test internationally recognized test which uses a biological assay to assess the mutagenic potential of chemical compounds 3.2 cartridge collector any party providing a cartridge take-back or collection program such as a business entity de

35、signated to collect cartridges 3.3 cartridge supplier cartridge marketer, manufacturer, remanufacturer, refiller, or distributor, being the party or parties responsible for marketing the cartridge and providing customer support for the cartridge 3.4 cartridge end-of-life point in a cartridge life-cy

36、cle from which the cartridge is no longer used for its intended purpose without additional non-customer interaction 3.5 end-of-life phase in a cartridge life-cycle when the cartridge can no longer be used for its intended purpose without additional non-customer interaction 3.6 environment surroundin

37、gs in which an organization operates, including air, water, land, natural resources, flora, fauna, humans, and their interaction ISO Guide 64 3.7 environmental provision any requirement, recommendation or statement in a standard that addresses environmental issues ISO Guide 64 BS ISO/IEC 29142-3:201

38、3 ISO/IEC 29142-3:2013(E) ISO/IEC 2013 All rights reserved 33.8 landfilled waste disposal in a landfill or other non-reuse, -recycle, -remanufacture, -waste to energy, or -incineration depository, excluding the residuals from waste to energy and incineration 3.9 incineration disposal method that inv

39、olves combustion of waste material converting it into heat, gas, steam and ash but not including smelting 3.10 life-cycle consecutive and interlinked stages of a product system, from raw material to acquisition or generation from natural resources to final disposition ISO 14040:2006, definition 3.1

40、3.11 life-cycle assessment compilation and evaluation of the inputs, outputs and the potential environmental impacts of a product system throughout its life-cycle 3.12 material safety data sheet MSDS form containing safety information about the ink or toner contained in cartridges designed for use i

41、n printing applications; and which includes physical, chemical, and toxicological properties, regulatory information, and recommendation to ensure safe handling 3.13 safety data sheet SDS form containing safety information about the ink or toner contained in cartridges designed for use in printing a

42、pplications; and which includes physical, chemical, and toxicological properties, regulatory information, and recommendation to ensure safe handling 3.14 non-original cartridge cartridge that is marketed by a company other than the company that markets the printing system for which the cartridge is

43、intended 3.15 original cartridge cartridge that is marketed by the company that markets the printing system for which the cartridge is intended 3.16 prevent indicates a condition of zero allowance of an intentionally added substance 3.17 product environmental aspect element of a product that, during

44、 its lifecycle, can interact with the environment ISO 14001 3.18 product environmental criteria environmental requirements that the product shall meet in order to be awarded an environmental label BS ISO/IEC 29142-3:2013 ISO/IEC 29142-3:2013(E) 4 ISO/IEC 2013 All rights reservedISO 14024 3.19 produc

45、t environmental impact any change to the environment, wholly or partly resulting from a product environmental aspect ISO 14001 3.20 recovery process to divert cartridges and/or cartridge materials from the solid waste stream and into productive uses 3.21 recyclable product that can be collected, sep

46、arated, or otherwise recovered from the solid waste stream for reuse, or in the manufacture or assembly of another package or product, through an established recycling program 3.22 recycle reuse, remanufacture or otherwise divert from a solid waste stream 3.23 recycled content percent, by mass, of r

47、ecycled material in a product or packaging 3.24 recycled material materials that have been recovered or otherwise diverted from the solid waste stream, either during the manufacturing process or after consumer use 3.25 recycling activities where components or materials that have been recovered or ot

48、herwise diverted from the solid waste stream are put into productive use as a material or component 3.26 refill operation to replace ink or toner in a customers cartridge that does not involve the replacement or refurbishing of worn cartridge components 3.27 refiller cartridge supplier that refills

49、customers cartridges 3.28 remanufacture operation to replace or clean components and add ink or toner using cartridges from cartridge take-back or collection programs 3.29 remanufacturer cartridge supplier that produces or markets remanufactured cartridges 3.30 restrict indicates a condition of specifically constrained or limited allowance BS ISO/IEC 29142-3:2013 ISO/IEC 29142-3:2013(E) ISO/IEC 2013 All rights reserved 53.31 reuse operation in which a whole or a component part of a c