BS ISO IEC 7811-9-2015 Identification cards Recording technique Tactile identifier mark《识别卡 记录技术 触摸识别符标记》.pdf

1、BSI Standards Publication BS ISO/IEC 7811-9:2015 Identification cards Recording technique Part 9: Tactile identifier markBS ISO/IEC 7811-9:2015 BRITISH STANDARD National foreword This British Standard is the UK implementation of ISO/IEC 7811-9:2015. It supersedes BS ISO/IEC 7811-9:2008 which is with

2、drawn. The UK participation in its preparation was entrusted to Technical Committee IST/17, Cards and personal identification. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions

3、of a contract. Users are responsible for its correct application. The British Standards Institution 2015. Published by BSI Standards Limited 2015 ISBN 978 0 580 81356 6 ICS 35.240.15 Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published

4、 under the authority of the Standards Policy and Strategy Committee on 31 December 2015. Amendments/corrigenda issued since publication Date T e x t a f f e c t e dBS ISO/IEC 7811-9:2015 Identification cards Recording technique Part 9: Tactile identifier mark Cartes didentification Technique denregi

5、strement Partie 9: Marque didentificateur tactile INTERNATIONAL STANDARD ISO/IEC 7811-9 Reference number ISO/IEC 7811-9:2015(E) Second edition 2015-12-01 ISO/IEC 2015 BS ISO/IEC 7811-9:2015ii ISO/IEC 2015 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO/IEC 2015, Published in Switzerland All rig

6、hts reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from e

7、ither ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Ch. de Blandonnet 8 CP 401 CH-1214 Vernier, Geneva, Switzerland Tel. +41 22 749 01 11 Fax +41 22 749 09 47 copyrightiso.org www.iso.org ISO/IEC 7811-9:2015(E)BS ISO/IEC 7811-9:2015ISO/IEC 7811-9:

8、2015(E)Foreword iv 1 Scope .1 2 Conformance .1 3 Terms and definitions .1 4 TIM physical characteristics .1 4.1 Location of TIM . 1 4.2 TIM dot arrangement 2 4.3 Dot dimensions . 3 4.4 Sign design 3 ISO/IEC 2015 All rights reserved iii Contents PageBS ISO/IEC 7811-9:2015ISO/IEC 7811-9:2015(E) Forewo

9、rd ISO (the International Organization for Standardization) and IEC (the International Electrotechnical Commission) form the specialized system for worldwide standardization. National bodies that are members of ISO or IEC participate in the development of International Standards through technical co

10、mmittees established by the respective organization to deal with particular fields of technical activity. ISO and IEC technical committees collaborate in fields of mutual interest. Other international organizations, governmental and non-governmental, in liaison with ISO and IEC, also take part in th

11、e work. In the field of information technology, ISO and IEC have established a joint technical committee, ISO/IEC JTC 1. The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval c

12、riteria needed for the different types of document should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements of this document may be the subject of

13、patent rights. ISO and IEC shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any tra

14、de name used in this document is information given for the convenience of users and does not constitute an endorsement. For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the T

15、echnical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information The committee responsible for this document is ISO/IEC JTC 1 Information technology, Subcommittee SC 17, Cards and personal identification. This second edition cancels and replaces the first edition (ISO/IEC

16、 78119:2008), which has been technically revised. ISO/IEC 7811 consists of the following parts, under the general title Identification cards Recording technique: Part 1: Embossing Part 2: Magnetic stripe Low coercivity Part 6: Magnetic stripe High coercivity Part 7: Magnetic stripe High coercivity,

17、high density Part 8: Magnetic stripe Coercivity of 51,7 kA/m (650 Oe) Part 9: Tactile identifier mark Notes in this part of ISO/IEC 7811 are only used for giving additional information intended to assist in the understanding or use of the document. They do not contain provisions or requirements to w

18、hich it is necessary to conform in order to claim compliance with this part of ISO/IEC 7811.iv ISO/IEC 2015 All rights reservedBS ISO/IEC 7811-9:2015INTERNATIONAL ST ANDARD ISO/IEC 7811-9:2015(E) Identification cards Recording technique Part 9: Tactile identifier mark 1 Scope This part of ISO/IEC 78

19、11 specifies the physical characteristics of a tactile identifier mark used by visually impaired card holders to distinguish their cards. It defines the area on the card for the TIM and the layout of Braille style embossed dots arranged in patterns to enable easy tactile recognition. 2 Conformance A

20、 TIM is in conformance with this part of ISO/IEC 7811 if it meets all mandatory requirements and optional requirements as specified. 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO/IEC 7810 and the following apply. 3.1 TIM tactile identifier mark 3.2

21、 embossed raised in relief from the front surface of the card by adding or reacting card material or by deforming the card material from the opposite side 4 TIM physical characteristics 4.1 Location of TIM The TIM should be located on the front surface of the card in the area shown in Figure 1. The

22、TIM shall not be located outside the name and address area defined by ISO/IEC 7811-1. Regardless of TIM location, all other raised areas shall be at least 1 mm from the edge of any TIM. When the technology used to form the raised areas causes a physical deformation of the card such as mechanical emb

23、ossing, then special care shall be taken that such deformation of the card does not adversely affect the required characteristics of the contained components such as IC, antenna, connecting wires, etc. A minimum distance of 3 mm between the contained components and any deformed part of the card is r

24、ecommended unless it is known that the components are not affected by the deformation of the card. ISO/IEC 2015 All rights reserved 1BS ISO/IEC 7811-9:2015ISO/IEC 7811-9:2015(E) The recommended TIM location is shown in Figure 1 as “Default area”. If the “Alternate area” for TIM is used, there shall

25、be no other raised area to the right and below the TIM dots (between TIM dots and nearest edges of card). NOTE The alternate area is raised up to avoid overlapping on the antenna of a contactless IC card but is still low enough to be in the name and address area as required and to be at least 1 mm a

26、way from the primary account line (both specified in ISO/IEC 7811-1). Dimensions in millimetres (inches) b 1 2 Key 1 top reference edge 2 front of card 3 TIM areaDefault area Alternate area a 18,5 (0.728) maximum 18,5 (0.728) maximum b 8 (0.315) maximum 8 (0.315) maximum c 10 1 (0.394 0.039) 10 1 (0

27、.394 0.039) d 2,92 0,38 (0.115 0.015) 9,07 0,38 (0.357 0.015) Figure 1 TIM area 4.2 TIM dot arrangement The TIM shall be composed of a maximum of three groups of six dots arranged as shown in Figure 2.2 ISO/IEC 2015 All rights reservedBS ISO/IEC 7811-9:2015ISO/IEC 7811-9:2015(E) Dimensions in millim

28、etres (inches) Key a 2,3 (0.091) b 4,6 (0.181) c 2,3 (0.091) three places d 6,1 (0.240) e 12,2 (0.480) Figure 2 Arrangement of TIM dots 4.3 Dot dimensions Dots used to make up the TIM shall have a relief height of 0,48 mm (0.019 in) maximum and 0,3 mm (0.012 in) minimum above the adjacent surface of

29、 the card. The shape of each dot is not specified, examples are shown in Figure 3. Dimensions in millimetres (inches) Figure 3 TIM dot base size and shape illustration 4.4 Sign design It is recommended that the cardholder select which of the 18 possible dots are to be raised. The maximum number of r

30、aised dots is 18 and the minimum is 1. NOTE Since there are individual differences in discernment by the tactile sense, it is recommended that the card holder be able to use the combination of the dots that is easy for them to discriminate. ISO/IEC 2015 All rights reserved 3BS ISO/IEC 7811-9:2015ISO

31、/IEC 7811-9:2015(E) ISO/IEC 2015 All rights reserved ICS 35.240.15 Price based on 3 pagesThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services. BSI is incorporated by Royal Charter. Bri

32、tish Standards and other standardization products are published by BSI Standards Limited. British Standards Institution (BSI) BSI Group Headquarters 389 Chiswick High Road London W4 4AL UK About us We bring together business, industry, government, consumers, innovators and others to shape their comb

33、ined experience and expertise into standards -based solutions. The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their

34、goals. Information on standards We can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre. Buying standards You can buy and download PDF versions of BSI

35、 publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services te

36、am. Subscriptions Our range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to With British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards

37、 from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS

38、 is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit With a Multi-User Network Licenc

39、e (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is current. For further information, email . Revisions Our British Standards and other

40、publications are updated by amendment or revision. We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre. Copyright All the data, software

41、and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for comm

42、ercial publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. Details

43、and advice can be obtained from the Copyright & Licensing Department. Useful Contacts: Customer Services Tel: +44 845 086 9001 Email (orders): Email (enquiries): Subscriptions Tel: +44 845 086 9001 Email: Knowledge Centre Tel: +44 20 8996 7004 Email: Copyright & Licensing Tel: +44 20 8996 7070 Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW