BS ISO IEC 7816-1-2011 Identification cards Integrated circuit cards Cards with contacts Physical characteristics《识别卡 集成电路卡 带触点卡 物理特征 n》.pdf

1、raising standards worldwide NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BSI Standards Publication BS ISO/IEC 7816-1:2011 Identification cards Integrated circuit cards Part 1: Cards with contacts Physical characteristicsBS ISO/IEC 7816-1:2011 BRITISH STANDARD National forew

2、ord This British Standard is the UK implementation of ISO/IEC 7816-1:2011. It supersedes BS ISO/IEC 7816-1:1998+A1:2003 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee IST/17, Cards and personal identification. A list of organizations represented on t

3、his committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. BSI 2011 ISBN 978 0 580 69840 8 ICS 35.240.15 Compliance with a British Standard cannot confer immuni

4、ty from legal obligations. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 March 2011. Amendments issued since publication Date Text affectedBS ISO/IEC 7816-1:2011Reference number ISO/IEC 7816-1:2011(E) ISO/IEC 2011INTERNATIONAL STANDARD I

5、SO/IEC 7816-1 Second edition 2011-02-15 Identification cards Integrated circuit cards Part 1: Cards with contacts Physical characteristics Cartes didentification Cartes circuit intgr Partie 1: Cartes contacts Caractristiques physiques BS ISO/IEC 7816-1:2011 ISO/IEC 7816-1:2011(E) PDF disclaimer This

6、 PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept ther

7、ein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; th

8、e PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUM

9、ENT ISO/IEC 2011 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member b

10、ody in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO/IEC 2011 All rights reservedBS ISO/IEC 7816-1:2011 ISO/IEC 7816-1:2011(E) ISO/IEC 2011 All

11、rights reserved iiiForeword ISO (the International Organization for Standardization) and IEC (the International Electrotechnical Commission) form the specialized system for worldwide standardization. National bodies that are members of ISO or IEC participate in the development of International Stand

12、ards through technical committees established by the respective organization to deal with particular fields of technical activity. ISO and IEC technical committees collaborate in fields of mutual interest. Other international organizations, governmental and non-governmental, in liaison with ISO and

13、IEC, also take part in the work. In the field of information technology, ISO and IEC have established a joint technical committee, ISO/IEC JTC 1. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of the joint technical committee i

14、s to prepare International Standards. Draft International Standards adopted by the joint technical committee are circulated to national bodies for voting. Publication as an International Standard requires approval by at least 75 % of the national bodies casting a vote. Attention is drawn to the poss

15、ibility that some of the elements of this document may be the subject of patent rights. ISO and IEC shall not be held responsible for identifying any or all such patent rights. ISO/IEC 7816-1 was prepared by Joint Technical Committee ISO/IEC JTC 1, Information technology, Subcommittee SC 17, Cards a

16、nd personal identification. This second edition cancels and replaces the first edition (ISO/IEC 7816-1:1998), which has been technically revised. It also incorporates the Amendment ISO/IEC 7816-1:1998/Amd.1:2003. ISO/IEC 7816 consists of the following parts, under the general title Identification ca

17、rds Integrated circuit cards: Part 1: Cards with contacts Physical characteristics Part 2: Cards with contacts Dimensions and location of the contacts Part 3: Cards with contacts Electrical interface and transmission protocols Part 4: Organization, security and commands for interchange Part 5: Regis

18、tration of application providers Part 6: Interindustry data elements for interchange Part 7: Interindustry commands for Structured Card Query Language (SCQL) Part 8: Commands for security operations Part 9: Commands for card management Part 10: Electronic signals and answer to reset for synchronous

19、cards Part 11: Personal verification through biometric methods Part 12: Cards with contacts USB electrical interface and operating procedures Part 13: Commands for application management in a multi-application environment Part 15: Cryptographic information application BS ISO/IEC 7816-1:2011 ISO/IEC

20、7816-1:2011(E) iv ISO/IEC 2011 All rights reservedIntroduction ISO/IEC 7816 is a series of International Standards specifying integrated circuit cards and the use of such cards for interchange. These cards are identification cards intended for information exchange negotiated between the outside worl

21、d and the integrated circuit in the card. As a result of an information exchange, the card delivers information (computation result, stored data) and/or modifies its content (data storage, event memorization). Five parts are specific to cards with galvanic contacts and three of them specify electric

22、al interfaces. ISO/IEC 7816-1 specifies physical characteristics for cards with contacts. ISO/IEC 7816-2 specifies dimensions and location of the contacts. ISO/IEC 7816-3 specifies electrical interface and transmission protocols for asynchronous cards. ISO/IEC 7816-10 specifies electrical interface

23、and answer to reset for synchronous cards. ISO/IEC 7816-12 specifies electrical interface and operating procedures for USB cards. All the other parts are independent of the physical interface technology. They apply to cards accessed by contacts and/or by contactless technology. ISO/IEC 7816-4 specif

24、ies organization, security and commands for interchange. ISO/IEC 7816-5 specifies registration of application providers. ISO/IEC 7816-6 specifies interindustry data elements for interchange. ISO/IEC 7816-7 specifies commands for structured card query language. ISO/IEC 7816-8 specifies commands for s

25、ecurity operations. ISO/IEC 7816-9 specifies commands for card management. ISO/IEC 7816-11 specifies personal verification through biometric methods. ISO/IEC 7816-13 specifies commands for application management in a multi-application environment. ISO/IEC 7816-15 specifies cryptographic information

26、application. BS ISO/IEC 7816-1:2011 INTERNATIONAL STANDARD ISO/IEC 7816-1:2011(E) ISO/IEC 2011 All rights reserved 1Identification cards Integrated circuit cards Part 1: Cards with contacts Physical characteristics 1 Scope This part of ISO/IEC 7816 specifies the physical characteristics of integrate

27、d circuit cards with contacts. It applies to identification cards of the ID-1 card type, which can include embossing and/or a magnetic stripe and/or tactile identifier mark as specified in ISO/IEC 7811. Test methods are specified in ISO/IEC 10373-1. This part of ISO/IEC 7816 applies to cards which h

28、ave a physical interface with electrical contacts. It does not, however, define the nature, number and position of the integrated circuits in the cards. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the ed

29、ition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO/IEC 7810, Identification cards Physical characteristics ISO/IEC 10373-1, Identification cards Test methods Part 1: General characteristics 3 Terms and definitions For th

30、e purposes of this document, the terms and definitions given in ISO/IEC 7810, ISO/IEC 10373-1 and the following apply. 3.1 integrated circuit IC electronic component designed to perform processing and/or memory functions 3.2 contact conducting element ensuring galvanic continuity between integrated

31、circuit and the external interfacing equipment 3.3 damaged not testably functional as defined in ISO/IEC 10373-1 BS ISO/IEC 7816-1:2011 ISO/IEC 7816-1:2011(E) 2 ISO/IEC 2011 All rights reserved4 Physical characteristics 4.1 General An ID-1 card shall fulfil the physical requirements given in 4.2 to

32、4.5 after the insertion of an IC into the card body. 4.2 Surface profile of contacts No point of the entire IC contact surface shall be higher than 0,10 mm above or lower than 0,10 mm below the adjacent surface of the card. A card issuer may require more stringent tolerances in accordance with its s

33、ector or its application-specific requirements. WARNING For cards which are printed after embedding, problems can be encountered when contacts are above the adjacent surface of the card. 4.3 Mechanical strength (of a card and contacts) The card should resist damage to its surface and to any componen

34、ts contained in it and should remain intact during normal use, storage and handling. Each contact surface and contact area (entire galvanic surface) shall not be damaged by a working pressure equivalent to a steel ball of diameter 1 mm applying a force of 1,5 N. 4.4 Electrical resistance (of contact

35、s) The contact resistance of a card connector assembly should be sufficiently low to enable a good contact between card and reader contacts. When a d.c. current of any value between 50 A and 100 mA is applied, the surface resistance between any two points on the same contact pad shall not exceed 0,5

36、 at a distance of 1,5 mm between contact points. The contact pad area is defined in ISO/IEC 7816-2. 4.5 Electromagnetic interference (between magnetic stripe and integrated circuit) If the card carries a magnetic stripe, the IC card shall not be damaged, malfunction or be altered after reading, writ

37、ing or erasing of the magnetic stripe. Conversely, the writing or reading of the IC shall not cause a malfunction of the magnetic stripe or its associated reading, writing or handling mechanisms. BS ISO/IEC 7816-1:2011 ISO/IEC 7816-1:2011(E) ISO/IEC 2011 All rights reserved 3Bibliography 1 ISO/IEC 7

38、811-1:2002, Identification cards Recording technique Part 1: Embossing 2 ISO/IEC 7811-2:2001, Identification cards Recording technique Part 2: Magnetic stripe Low coercivity 3 ISO/IEC 7811-6:2008, Identification cards Recording technique Part 6: Magnetic stripe High coercivity 4 ISO/IEC 7811-7:2004,

39、 Identification cards Recording technique Part 7: Magnetic stripe High coercivity, high density 5 ISO/IEC 7811-8:2008, Identification cards Recording technique Part 8: Magnetic stripe Coercivity of 51,7 kA/m (650 Oe) 6 ISO/IEC 7811-9:2008, Identification cards Recording technique Part 9: Tactile ide

40、ntifier mark 7 ISO/IEC 7813:2006, Information technology Identification cards Financial transaction cards 8 ISO/IEC 7816-2, Identification cards Integrated circuit cards Part 2: Cards with contacts Dimensions and location of the contacts BS ISO/IEC 7816-1:2011 ISO/IEC 7816-1:2011(E) ICS 35.240.15 Pr

41、ice based on 3 pages ISO/IEC 2011 All rights reserved This page deliberately left blankBSI is the independent national body responsible for preparing British Standards and other standards-related publications, information and services. It presents the UK view on standards in Europe and at the intern

42、ational level. It is incorporated by Royal Charter. British Standards Institution (BSI) raising standards worldwide BSI Group Headquarters 389 Chiswick High Road London W4 4AL UK Tel +44 (0)20 8996 9001 Fax +44 (0)20 8996 7001 British Standards are updated by amendment or revision. Users of British

43、 Stan- dards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and serv- ices. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of th

44、e technical com- mittee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001 BSI offers Members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Te

45、l: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001 Email: Buying standards You may buy PDF and hard copy versions of standards directly using a credit card from the BSI Shop on the website In addition all orders for BSI, international and foreign standards publications can be addressed to BSI Custome

46、r Services. Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001 Email: In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide

47、range of information on national, European and international standards through its Knowledge Centre. Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005 Email: Various BSI electronic information services are also available which give details on all its products and services. Tel: +44 (0)20 8996 7111

48、Fax: +44 (0)20 8996 7048 Email: BSI Subscribing Members are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Ad- ministration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via British Standards Online can be found at Further information about BSI is available on the BSI website at www.bsi- Copy