BS M 61-1989 Specification for envelope dimensions of P clamps (loop clamps) for fluid systems《液压系统用“P”形卡箍(环形卡箍()轮廓尺寸规范》.pdf

1、BRITISH STANDARD AEROSPACE SERIES BS M 61:1989 ISO 7315:1988 Specification for Envelope dimensions of “P” clamps (loop clamps) for fluid systemsBSM61:1989 This British Standard, having been prepared under the directionof the Aerospace Standards Policy Committee, waspublished under the authorityof th

2、e Board of BSI andcomes into effect on 29September1989 BSI 11-1999 The following BSI references relate to the work on this standard: Committee reference ACE/- Draft for comment 86/76683 DC ISBN 0 580 17507 3 Committees responsible for this British Standard The preparation of this British Standard wa

3、s entrusted by the Aerospace Standards Policy Committee (ACE/-) to subcommittee ACE/-/1, upon which the following bodies were represented: Civil Aviation Authority (Airworthiness Division) Institution of Production Engineers Ministry of Defence Society of British Aerospace Companies Limited Amendmen

4、ts issued since publication Amd. No. Date of issue CommentsBSM61:1989 BSI 11-1999 i Contents Page Committees responsible Inside front cover National foreword ii 1 Scope 1 2 Field of application 1 3 Reference 1 4 Classification 1 5 Description 1 6 Dimensions 1 Figure Maximum envelope dimensions for “

5、P” clamps (loop clamps) 2 Table 1 1 Table 2 3BSM61:1989 ii BSI 11-1999 National foreword This British Standard has been prepared under the direction of the Aerospace Standards Policy Committee. It is identical with ISO7315:1988 Aerospace “P” clamps (loop clamps) for fluid systems Envelope dimensions

6、 published by the International Organization for Standardization (ISO). ISO 7315 was produced as a result of international discussion in which the UK took an active part. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are respons

7、ible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Cross-reference International Standard Corresponding British Standard ISO 6771:1987 BS 2M51:1989 Classification for pressure and temperature for fluid systems and compone

8、nts (Identical) Summary of pages This document comprises a front cover, an inside front cover, pagesi andii, pages1 to3 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front co

9、ver.BSM61:1989 BSI 11-1999 1 1 Scope This International Standard specifies maximum and minimum dimensions for “P” clamps (loop clamps) installed by means of a bolt with a nominal diameter of5mm. The specified dimensions define a dimensional envelope. This International Standard shall not be consider

10、ed as an interchangeability standard. The tolerances for each type of clamp are to be defined in the parts standards drawings. 2 Field of application These clamps are intended for the installation, support and guiding of rigid tubing or hose assemblies used in aerospace equipment. NOTE“P” clamps (lo

11、op clamps) may also be used for other equipment, e.g. electrical cables or looms. 3 Reference ISO 6771, Aerospace Fluid systems and components Pressure and temperature classifications. 4 Classification “P” clamps (loop clamps) are classified into six types according to the temperature range in which

12、 they are intended to be used (seeTable 1). Table 1 5 Description The “P” clamp (loop clamp) is a “single-block” or a “multi-component”-type clamp. The “multi-component”-type clamp is provided as a metallic support with a plastomer or elastomer cushion or sheathing. 6 Dimensions The “P” clamp (loop

13、clamp) shall be in accordance with the Figure and Table 2. The shape of clamp illustrated in the Figure does not purport to be the exact shape of the manufactured clamp. Table 2 only specifies those dimensions required to define the maximum envelope and the proper location of the tube relative to th

14、e mounting plane and fastening point. Temperatures in degrees Celsius Clamp type Temperature range a min. max. 1 55 +70 2 55 +135 3 55 +200 4 55 +320 5 55 +400 6 55 +650 a See ISO 6771.BSM61:1989 2 BSI 11-1999 Figure Maximum envelope dimensions for “P” clamps (loop clamps)BSM61:1989 BSI 11-1999 3 Ta

15、ble 2 a Dimensions in millimetres Nominal diameter of tube DN b A B c D E F G H J K L c min. max. min. max. max. min. max. max. min. max. max. max. 04 05 06 08 10 12 14 16 18 20 22 25 28 32 36 40 45 50 56 63 70 80 90 100 11 11,5 12 13 14 15 17,5 18,5 19,5 20,5 21,5 23 24,5 26,5 28,5 30,5 33 35,5 38,

16、5 42 45,5 50,5 55,5 60,5 12,7 13,2 13,7 14,7 15,7 16,7 19,1 20,1 21,1 22,1 23,1 24,6 26,8 28,8 30,8 32,8 35,5 38 41 44,5 48 53 58 63 2,8 3,2 3,8 4,8 5,8 6,8 7,8 8,8 9,8 10,8 11,8 13,3 14,8 16,8 18,8 20,8 23 25,5 28,5 32 35,5 40,5 45,5 50,5 6,0 6,5 7,0 8,0 9,0 10 11,2 12,3 13,3 14,3 15,3 16,8 19,4 20

17、,7 21,7 24,7 27,3 29,8 32,8 36,3 39,8 44,8 49,8 54,8 2,5 2,5 2,5 2,5 2,5 2,5 3,3 3,3 3,3 3,3 3,3 3,3 4 4 4 4 4 4 4 4 4 4 4 4 8,1 8,1 8,1 8,1 8,1 8,1 8,8 8,8 8,8 8,8 8,8 8,8 9,1 9,1 9,1 9,1 9,1 9,1 9,1 9,1 9,1 9,1 9,1 9,1 5,5 5,5 5,5 5,5 5,5 5,5 5,5 5,5 5,5 5,5 5,5 5,5 5,5 5,5 5,5 5,5 5,5 5,5 5,5 5,5

18、 5,5 5,5 5,5 5,5 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,5 5,5 5,5 5,5 5,5 5,5 5,5 5,5 5,5 5,5 5,5 5,5 5,5 5,5 5,5 5,5 5,5 5,5 5,5 5,5 5,5 5,5 5,5 5,5 6,5 6,5 6,5 6,5 6,5 6,5 6,5 6,5 6,5 6,5 6,5

19、 6,5 6,5 6,5 6,5 6,5 6,5 6,5 6,5 6,5 6,5 6,5 6,5 6,5 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 a All dimensions in this table apply with the tube assembled in the tightened c

20、lamp. b Diameters DN 14, 18, 22, 28, 36, 45, 56, 70 and 90 are non-preferred sizes for tubing in fluid systems. c This dimension is an overall dimension which includes metal width and cushion or sheathing.0,3 + 0BSM 61:1989 ISO 7315:1988 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsIn

21、stitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards sh

22、ould make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical commit

23、tee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, i

24、nternational and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise req

25、uested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and servi

26、ces. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089

27、967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a ret

28、rieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designat

29、ions. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.