1、PD CEN/TR 15985:2010 ICS 13.220.50; 91.100.01 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW PUBLISHED DOCUMENT Thermal insulating products Factory made products of expanded polystyrene (EPS) Voluntary certification of the raw materialThis Published Document was published und
2、er the authority of the Standards Policy and Strategy Committee on 31 July 2010 BSI 2010 ISBN 978 0 580 68140 0 Amendments/corrigenda issued since publication Date Comments PD CEN/TR 15985:2010 National foreword This Published Document is the UK implementation of CEN/TR 15985:2010. The UK participat
3、ion in its preparation was entrusted to Technical Committee PRI/72/2, Polystyrene. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its
4、 correct application. Compliance with a British Standard cannot confer immunity from legal obligations.PD CEN/TR 15985:2010TECHNICAL REPORT RAPPORT TECHNIQUE TECHNISCHER BERICHT CEN/TR 15985 January 2010 ICS 13.220.50; 91.100.01 English Version Thermal insulating products - Factory made products of
5、expanded polystyrene (EPS) - Voluntary certification of the raw material Produits isolants - Produits manufacturs en polystyrne expans (EPS) - Certification volontaire du matriau de base Wrmedmmstoffe - Werkmig hergestellte Produkte aus expandiertem Polystyrol (EPS) - Freiwillige Zertifizierung des
6、Ausgangsstoffes This Technical Report was approved by CEN on 7 December 2009. It has been drawn up by the Technical Committee CEN/TC 88. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, H
7、ungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Ce
8、ntre: Avenue Marnix 17, B-1000 Brussels 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. CEN/TR 15985:2010: EPD CEN/TR 15985:2010 CEN/TR 15985:2010 (E) 2 Contents Page Foreword 3 Introduction .4 1 Scope 5 2 Normative references 5
9、3 Terms and definitions .5 4 Preparation of samples .6 5 Initial tests 6 6 Factory Production Control (FPC) for EPS raw material .6 6.1 General 6 6.2 Testing frequency 6 7 Certification of conformity for raw material 7 7.1 Bodies involved in the evaluation of conformity procedure .7 7.2 Test specime
10、ns 7 7.3 Initial test for EPS raw material 7 8 Continuous surveillance of EPS raw material 7 8.1 Production 7 8.2 Factory production control .7 9 Certificate of conformity .8 10 Responsibility of the raw material supplier 9 10.1 Declaration by the raw material supplier 9 10.2 Labelling .9 PD CEN/TR
11、15985:2010 CEN/TR 15985:2010 (E) 3 Foreword This document (CEN/TR 15985:2010) has been prepared by Technical Committee CEN/TC 88 “Thermal insulating materials and products”, the secretariat of which is held by DIN. Attention is drawn to the possibility that some of the elements of this document may
12、be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. PD CEN/TR 15985:2010 CEN/TR 15985:2010 (E) 4 Introduction EN 13163 contains an option in Annex B, Table B.2 to change the frequency for the reaction to fire test according
13、 to EN ISO 11925-2 from once per day to once per week. A reduction of the frequency in the FPC is possible according to note to table h of Table B.2, if a certified raw material has been used. Since rules on how to certify EPS raw material are still missing this option could not be chosen yet. That
14、is why the following rules have been developed and issued by TC 88. These rules may be applied by the raw material suppliers and the involved bodies to certify the raw materials until the following text has been incorporated in the next revision of EN 13163:2008. PD CEN/TR 15985:2010 CEN/TR 15985:20
15、10 (E) 5 1 Scope It is essential that EPS products with a reaction to fire performance better than Euroclass F be manufactured from raw materials with a chemical composition, which is under the control of the raw material producer. This Technical Report specifies the conditions allowing reduction of
16、 the FPC frequency for testing the reaction to fire of specimens made from flame retardant EPS raw material. The preconditions are that products are manufactured solely from a specified, certified raw material, within defined density limits, and produced in the way specified by the raw material supp
17、lier. The frequency of testing the final product can be reduced in accordance with EN 13163:2008, Annex B, Table B.2 footnote to table h. It is essential that the reaction to fire performance of the raw material be labelled according to 9.2 in the certificate from an approved body (see EN 13172:2008
18、, 5.3.3 and Annex A). The certification of the raw material relates only to products for which the reaction to fire Euroclass E according to EN 13501-1 is being claimed. The manufacturer of the EPS boards / products continues to be responsible for the FPC of the EPS boards / products. This Technical
19、 Report is in accordance with the general rules of EN 13172. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (
20、including any amendments) applies. EN 1602, Thermal insulating products for building applications Determination of the apparent density EN 13163:2008, Thermal insulation products for buildings Factory made products of expanded polystyrene (EPS) Specification EN 13172:2008, Thermal insulating product
21、s Evaluation of conformity EN 13501-1, Fire classification of construction products and building elements Part 1: Classification using data from reaction to fire tests EN ISO 11925-2, Reaction to fire tests Ignitability of building products subjected to direct impingement of flame Part 2: Single-fla
22、me source test (ISO 11925-2:2002) 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 EPS raw material with flame retardant non-expanded polystyrene beads containing additives such as a flame retardant treatment and a blowing agent 3.2 EPS test s
23、pecimen EPS foam in a finished form with its final product properties (without facing) NOTE ITT = Initial Type Test. PD CEN/TR 15985:2010 CEN/TR 15985:2010 (E) 6 4 Preparation of samples The raw material supplier shall produce samples of the expanded raw material using all the procedures of the norm
24、al production process for EPS. Thickness, density and exposure to thermal attack shall be measured and reported when making the ignitability test in accordance with EN ISO 11925-2. The specimens shall be cut from samples as described in EN ISO 11925-2. NOTE Since EPS is an isotropic material the dir
25、ection of the samples is irrelevant. The thickness of all test specimens shall be 10 mm and 60 mm for ITT. 5 Initial tests Initial type tests shall be carried out on samples as described in Clause 4. Test specimens, in thickness of 10 mm and 60 mm shall be made from the minimum and maximum density o
26、f EPS product sample. The tests shall be performed in accordance with EN ISO 11925-2 with the thermal attack on the edge. 6 Factory Production Control (FPC) for EPS raw material 6.1 General The raw material supplier shall have a factory production control system in place as described in EN 13172 to
27、ensure the quality of production. The continuous FPC of the raw materials shall be carried out by sampling EPS products produced at densities between 15 kg/m and 20 kg/m. The density of all samples prepared shall be determined in accordance with EN 1602. The tests shall be made and the results recor
28、ded in accordance with EN ISO 11925-2 with an exposure time of 15 s and an observation time of 20 s; edge attack only. All tests results shall fulfil the requirements to meet Euroclass E according to EN 13501-1. 6.2 Testing frequency The tests shall be performed on one set of specimens per batch (or
29、 per production day whichever gives the highest frequency) and per plant and type of polymer at a density between 15 kg/m and 20 kg/m. The thickness of the samples shall be 20 mm. In addition, the minimum and maximum density shall be tested and recorded every 3 months. The thickness of the samples s
30、hall be 20 mm. In case EN 13172 specifies applicable rules, the testing frequency can be reduced in agreement with the notified body if the raw material supplier has demonstrated reliable performance. PD CEN/TR 15985:2010 CEN/TR 15985:2010 (E) 7 7 Certification of conformity for raw material 7.1 Bod
31、ies involved in the evaluation of conformity procedure Bodies involved are specified in EN 13172:2008, Annex A. 7.2 Test specimens The number of test specimens to obtain one test result is specified in EN 13501-1 and EN ISO 11925-2. The raw material supplier shall send the samples to the approved bo
32、dy. 7.3 Initial test for EPS raw material For the initial type test the tests shall be performed by an approved body taking into account the more critical edge flame attack only (not the surface attack). NOTE EN ISO 11925-2 requires both testing with surface and edge flame attack, but for this purpo
33、se here only the more critical test is performed. The specimen thickness shall be 10 mm and 60 mm, for both the minimum and maximum density. These two densities specify the density range for which the certificate is valid. A classification report according to EN 13501-1 from an approved body is requ
34、ired for the initial test only. This test shall be repeated every 5 years. 8 Continuous surveillance of EPS raw material 8.1 Production Plant and polymer samples, at the minimum and maximum density shall be tested by an approved body once per year with a specimen thickness of 20 mm. Different fracti
35、ons of one production line can be grouped together within the defined density range. 8.2 Factory production control The FPC shall be checked by an approved body once per year. PD CEN/TR 15985:2010 CEN/TR 15985:2010 (E) 8 Table 1 Testing frequency Test Frequency Test performed by Thickness of the sam
36、ples Density of the samples Initial type test 1 / 5 years Raw material supplier 10 mm and 60 mm Minimum and maximum Factory production control 1 / day or 1 / batch (which gives the highest frequency) Raw material supplier 20 mm Between 15 kg/m and 20 kg/m 1 / 3 months Raw material supplier 20 mm Min
37、imum and maximum Initial type test 1 / 5 years Notified body 10 mm and 60 mm Minimum and maximum Continuous surveillance 1 / year Notified body 10 mm and 60 mm Minimum and maximum 9 Certificate of conformity The approved body shall issue a certificate of conformity according to EN 13172:2008, Annex
38、A. The validity of the certificate shall be limited to 5 years. The certificate cannot be used directly by the EPS producer, but can be used to reduce the testing frequency in his FPC. The certificate shall contain the following information: Heading: “Certificate of conformity according to EN 13163:
39、2008, Annex E” Certified EPS raw material. “EPS Products made of this raw material (not mixed with other materials) and within a density range from kg/m 3to kg/m 3will fulfil the requirements of class E according to EN 13501-1” EPS raw material supplier Production plant Product name Issuing date and
40、 duration of validity of the certificate “The validity of the certification of conformity shall be checked once a year by an approved body. If a product no longer complies with the requirements for this certificate, the EPS producer shall be informed immediately by the raw material supplier”. Name,
41、address and identification number of the approved body. PD CEN/TR 15985:2010 CEN/TR 15985:2010 (E) 9 10 Responsibility of the raw material supplier 10.1 Declaration by the raw material supplier The raw material supplier may affix information on the containers or in the delivery documents, concerning
42、 his certified EPS raw material only after the certificate of conformity has been obtained and the corresponding FPC requirements have been met. The initial certificate shall be provided to the EPS producers by the raw material supplier. The validity period of the declaration of the conformity shall
43、 be expressed by the declaration on the label. In case of non-conformity the raw material supplier shall immediately cease to make the conformity declaration. The validity of the certification shall be verified by the approved body at least once a year, with reference to the annual test-reports. An
44、example for this reference is: “Test on samples made from the raw material demonstrates that products made from the raw material comply with the requirements of EN 13163 for raw material, Euroclass E in accordance with EN 13501-1 (see test reports) and that the certification of conformity has been v
45、erified. The next verification is due by (month, year)”. The raw material supplier shall inform the approved body about relevant changes to his FPC and third party control procedure. The raw material supplier shall inform the relevant manufacturers about all changes in this certificate of conformity
46、. 10.2 Labelling On the label of the raw material the following shall be declared: certified raw material according to Technical Report CEN/TR 15985; products made of this raw material will obtain Euroclass E in accordance with EN 13501-1; raw material supplier; production plant; product name; appro
47、ved body and number of the certificate. PD CEN/TR 15985:2010 BSI Group Headquarters 389 Chiswick High Road, London, W4 4AL, UK Tel +44 (0)20 8996 9001 Fax +44 (0)20 8996 7001 standards BSI - British Standards Institution BSI is the independent national body responsible for preparing British Standar
48、ds. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constan
49、t aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically r
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1