BS PD CEN TS 12200-2-2017 Plastics rainwater piping systems for above ground external use Unplasticized poly(vinyl chloride) (PVC-U) Guidance for the assessment of conform.pdf

1、Plastics rainwater piping systems for above ground external use Unplasticized poly(vinyl chloride) (PVC-U) Part 2: Guidance for the assessment of conformity PD CEN/TS 12200-2:2017 BSI Standards Publication WB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06National foreword This Published Docum

2、ent is the UK implementation of CEN/TS 12200- 2:2017. It supersedes DD CEN/TS 12200-2:2003 which is withdrawn. The UK participation in its preparation was entrusted by Technical Committee PRI/88, Plastics piping systems, to Subcommittee PRI/88/1, Plastics piping for non-pressure applications. A list

3、 of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2017. Published by BSI Standards

4、Limited 2017 ISBN 978 0 580 94290 7 ICS 23.040.05 Compliance with a British Standard cannot confer immunity from legal obligations. This Published Document was published under the authority of the Standards Policy and Strategy Committee on 28 February 2017. Amendments/corrigenda issued since publica

5、tion Date Text affected PUBLISHED DOCUMENT PD CEN/TS 12200-2:2017 TECHNICAL SPECIFICATION SPCIFICATION TECHNIQUE TECHNISCHE SPEZIFIKATION CEN/TS 12200-2 February 2017 ICS 23.040.05 Supersedes CEN/TS 12200-2:2003 English Version Plastics rainwater piping systems for above ground external use - Unplas

6、ticized poly(vinyl chloride) (PVC-U) - Part 2: Guidance for the assessment of conformity Systmes de canalisations de descentes deaux pluviales en plastique usage externe en arien - Poly(chlorure de vinyle) non plastifi (PVC-U) - Partie 2 : Guide pour lvaluation de la conformit Kunststoff-Rohrleitung

7、ssysteme fr auenliegende Regenfallleitungen - Weichmacherfreies Polyvinylchlorid (PVC-U) - Teil 2: Empfehlungen fr die Beurteilung der Konformitt This Technical Specification (CEN/TS) was approved by CEN on 4 December 2016 for provisional application. The period of validity of this CEN/TS is limited

8、 initially to three years. After two years the members of CEN will be requested to submit their comments, particularly on the question whether the CEN/TS can be converted into a European Standard. CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to m

9、ake the CEN/TS available promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in parallel to the CEN/TS) until the final decision about the possible conversion of the CEN/TS into an EN is reached. CEN members are the national standards

10、 bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia,

11、 Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form and by any means res

12、erved worldwide for CEN national Members. Ref. No. CEN/TS 12200-2:2017 E PD CEN/TS 12200-2:2017CEN/TS 12200-2:2017 (E) 2 Contents Page European foreword . 3 Introduction 4 1 Scope 5 2 Normative references 5 3 Terms and definitions, 6 4 Abbreviated terms 9 5 General 9 6 Testing and inspection 9 6.1 M

13、aterial specification 9 6.1.1 PVC-U material . 9 6.1.2 Acrylic material 10 6.1.3 Other material . 11 6.2 Grouping 11 6.2.1 General . 11 6.2.2 Size groups 11 6.2.3 Fitting groups 11 6.3 Type testing 11 6.4 Batch release tests . 14 6.5 Process verification tests 15 6.6 Audit tests . 16 6.7 Indirect te

14、sts (IT) . 18 6.8 Test records . 18 Annex A (informative) Basic test matrix . 19 Bibliography . 20 PD CEN/TS 12200-2:2017CEN/TS 12200-2:2017 (E) 3 European foreword This document (CEN/TS 12200-2:2017) has been prepared by Technical Committee CEN/TC 155 “Plastics piping systems and ducting systems”,

15、the secretariat of which is held by NEN. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. This document supersedes CEN/TS 12200-2:2003. Compared with

16、CEN/TS 12200-2:2003, the following changes have been made: a) use of the template drafted by CEN/TC 155/WG 21 for assessment of conformity documents (change of “Terms and definitions” and addition of 1 column “Sampling procedures” in Tables); b) introduction of “Limits of addition of PVC reprocessed

17、 and recycled material” in a separate table (Table 2); c) addition of an informative Annex A: Basic test matrix. EN 12200 consists of the following Parts, under the general title “Plastics rainwater piping systems for above ground external use Unplasticized poly (vinyl chloride) (PVC-U)”. Part 1: Sp

18、ecifications for pipes, fittings and the system; Part 2: Guidance for the assessment of conformity; According to the CEN-CENELEC Internal Regulations, the national standards organisations of the following countries are bound to announce this European Standard: Austria, Belgium, Bulgaria, Croatia, Cy

19、prus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and

20、the United Kingdom. PD CEN/TS 12200-2:2017CEN/TS 12200-2:2017 (E) 4 Introduction Figures 1 and 2 are intended to provide general information on the concept of testing and organization of those tests used for the purpose of the assessment of conformity. For each type of test, i.e. type test (TT), bat

21、ch release test (BRT), process verification test (PVT) and audit test (AT), this part of EN 12200 details the applicable characteristics to be assessed and the frequency and sampling of testing. A typical scheme for the assessment of conformity of materials (formulations), pipes, fittings or assembl

22、ies by manufacturers is given in Figure 1. Figure 1 Typical scheme for the assessment of conformity by a manufacturer A typical scheme for the assessment of conformity of materials (formulations), pipes, fittings, valves or assemblies by manufacturers, including a third-party certification, is given

23、 in Figure 2. PD CEN/TS 12200-2:2017CEN/TS 12200-2:2017 (E) 5 Figure 2 Typical scheme for the assessment of conformity by a manufacturer, including certification 1 Scope This part of EN 12200 gives guidance for the assessment of conformity of formulations, products, joints and assemblies in accordan

24、ce with EN 12200-1:2016 intended to be included in the manufacturers quality plan as part of the quality management system and for the establishment of third-party certification procedures. NOTE In order to help the reader, a basic test matrix is given in Annex A. In conjunction with EN 12200-1:2016

25、, this document is applicable to piping systems made of unplasticized poly(vinyl chloride) (PVC-U) intended to be used for above ground external rainwater, and to fittings and brackets made of acrylic materials which may be used in combination with the pipes. 2 Normative references The following doc

26、uments, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 12200-1:2016, Plastic

27、s rainwater piping systems for above ground external use - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes, fittings and the system PD CEN/TS 12200-2:2017CEN/TS 12200-2:2017 (E) 6 3 Terms and definitions, For the purposes of this document, the terms and definitions give

28、n in EN 12200-1:2016, and the following apply. 3.1 certification body impartial body, governmental or non-governmental, possessing the necessary competence and responsibility to carry out certification of conformity according to given rules of procedure and management Note 1 to entry: A certificatio

29、n body is preferably accredited to EN ISO/IEC 17021 2. 3.2 inspection body body, that performs inspection SOURCE: EN ISO/IEC 17020:2012 3, 2.2 Note 1 to entry: A body can be an organization, or part of an organization. Note 2 to entry: A inspection body is preferably compliant with EN ISO/IEC 17020

30、3. 3.3 testing laboratory laboratory which measures, tests, calibrates or otherwise determines the characteristics of the performance of materials and products Note 1 to entry: In the context of this part of EN 12202, the materials and products can be subjected to type testing, batch release testing

31、, process verification testing, audit testing, and witness testing, as applicable. Note 2 to entry: A testing laboratory is preferably compliant with EN ISO/IEC 17025 4. 3.4 quality management system management system to direct and control an organization with regard to quality SOURCE: EN ISO 9000:2

32、015 5, 3.2.3 Note 1 to entry: Requirements for quality management systems are given in EN ISO 9001 1. 3.5 quality plan document setting out the specific quality practices, resources and sequence of activities relevant to a particular product or range of products 3.6 type testing TT testing performed

33、 to prove that the formulation, product, joint or assembly is capable of conforming to the requirements given in the relevant standard Note 1 to entry: The type test results remain valid until there is a change in the material or product or assembly provided that the process verification tests are d

34、one regularly. PD CEN/TS 12200-2:2017CEN/TS 12200-2:2017 (E) 7 3.7 batch release test BRT test performed by or on behalf of the manufacturer on a batch of materials or products, which needs to be satisfactorily completed before the batch can be released 3.8 process verification test PVT test perform

35、ed by, or on behalf of the manufacturer on materials, products or joints or assemblies at specific intervals to confirm that the process continues to be capable of producing products which conform to the requirements given in the relevant standard Note 1 to entry: Such tests are not required to rele

36、ase batches of materials or products; rather they are carried out as a measure of process control. 3.9 audit test AT test performed by a test laboratory on behalf of an inspection body or certification body to confirm that the material, product, joint or assembly continues to conform to the requirem

37、ents given in the relevant standard and to provide information to assess the effectiveness of the quality management system 3.10 indirect test IT test performed by or on behalf of the manufacturer, different from that specified test for that particular characteristic, having previously verified its

38、correlation with the specified test 3.11 witness test WT test accepted by an inspection or a certification body for type testing and/or audit testing, which is carried out by or on behalf of the manufacturer and supervised by a representative of the inspection or certification body, qualified in tes

39、ting 3.12 material generic term for formulations grouped by families, expressed by generic names, e.g. poly(vinyl chloride) (PVC), stainless steel, brass or EPDM Note 1 to entry: Definition from European Commission, Directorate-General for Enterprise and Industry, Sub- group on Product Testing Proce

40、dures (EC, DG ENT and IND, SG PTP). 3.13 formulation clearly defined homogenous mixture of base polymer with additives, i.e. anti-oxidants, pigments, stabilizers and others, at a dosage level necessary for the processing and the intended use of the final product Note 1 to entry: The term “compound”

41、is sometime used with similar meaning as “formulation”. PD CEN/TS 12200-2:2017CEN/TS 12200-2:2017 (E) 8 3.14 material batch clearly identified quantity of a given homogeneous formulation manufactured under uniform conditions and defined and identified by the formulation manufacturer 3.15 product pip

42、e or fitting of a clearly identified type intended to be a part of a piping system which the manufacturer puts on the market 3.16 product batch clearly identified collection of products, manufactured consecutively or continuously under the same conditions, using the same formulations and conforming

43、to the same specification Note 1 to entry: The production batch is defined and identified by the product manufacturer. 3.17 sample one or more products drawn from the same production batch, selected at random without regard to their quality Note 1 to entry: The number of products in the sample is th

44、e sample size. 3.18 group collection of similar products from which samples are selected for testing purposes 3.19 component product manufactured out of a specific formulation, brought to the market as part of another product or as a spare part 3.20 joint connection between two products 3.21 assembl

45、y product that can be dismantled into a set of components EXAMPLE A test piece consisting of various products. 3.22 sampling plan specification of the type of sampling to be used in combination with the operational specification of the entities or increments to be taken, the samples to be constitute

46、d and the measurements or tests to be made EXAMPLE A specific plan which indicates the number of units of products or assemblies to be inspected. 3.23 product type generic description of a product PD CEN/TS 12200-2:2017CEN/TS 12200-2:2017 (E) 9 EXAMPLE A pipe or its main parts, of the same design, f

47、rom a particular formulation. 3.24 cavity (moulding) space within a mould to be filled to form the moulded product EXAMPLE That part of the injection mould which gives the form to the injection moulded product. 4 Abbreviated terms To avoid misunderstanding, the abbreviations in this clause are defin

48、ed as being the same in each language. For the same reason, the terms are given in the three languages, English, French and German. EN FR DE AT audit test essai daudit berwachungsprfung BRT batch release test essai de libration de campagne de fabrication Freigabeprfung einer Charge IT indirect test

49、essai indirect indirekte Prfung PVT process verification test essai de vrification du procd de fabrication Prozessberprfung TT type test essai de type Typprfung WT witness testing essai tmoin Prfung unter Aufsicht 5 General 5.1 Formulation, products, joints and assemblies shall conform to the requirements given in EN 12200-1. 5.2 Products and assemblies shall be produced by the manufacturer under a quality management system which includes a quality plan . It is recommended that the quality management system conforms to, or