BS PD IEC TR 62839-1-2014 Environmental declaration Wires cables and accessory products Specific rules《环境声明 电线 电缆及附件产品 具体规则》.pdf

1、BSI Standards Publication Environmental declaration Part 1: Wires, cables and accessory products Specific rules PD IEC/TR 62839-1:2014National foreword This Published Document is the UK implementation of IEC/TR 62839-1:2014. The UK participation in its preparation was entrusted to Technical Commit-

2、tee EPL/46, Cables, wires and waveguides, radio frequency connectors and accessories for communication and signalling. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a con

3、tract. Users are responsible for its correct application. The British Standards Institution 2014. Published by BSI Standards Limited 2014 ISBN 978 0 580 82395 4 ICS 13.020.01; 33.120.10; 33.120.20 Compliance with a British Standard cannot confer immunity from legal obligations. This Published Docume

4、nt was published under the authority of the Standards Policy and Strategy Committee on 30 November 2014. Amendments/corrigenda issued since publication Date Text affected PUBLISHED DOCUMENT PD IEC/TR 62839-1:2014 IEC TR 62839-1 Edition 1.0 2014-11 TECHNICAL REPORT Environmental declaration Part 1: W

5、ires, cables and accessory products Specific rules INTERNATIONAL ELECTROTECHNICAL COMMISSION P ICS 13.020.01; 33.120.10; 33.120.20 PRICE CODE ISBN 978-2-8322-1921-8 Registered trademark of the International Electrotechnical Commission Warning! Make sure that you obtained this publication from an aut

6、horized distributor. colour inside PD IEC/TR 62839-1:2014 2 IEC TR 62839-1:2014 IEC 2014 CONTENTS FOREWORD . 3 1 Scope 5 2 Normative references 5 3 Terms and definitions . 6 4 Communication and data wires and cables 7 4.1 Functional unit and reference flow description. 7 4.2 System boundaries . 8 Ov

7、erview . 8 4.2.1Installation phase 8 4.2.2Use phase . 8 4.2.3Lifetime and use rates . 12 4.2.4End of life phase 12 4.2.5 5 Control and command wires and cables . 13 5.1 Functional unit and reference flow description. 13 5.2 System boundaries . 13 Overview . 13 5.2.1Installation phase 13 5.2.2Use pha

8、se . 14 5.2.3End of life phase 14 5.2.4 6 Accessories FFS . 14 Annex A (informative) Applications 15 Table 1 Twisted pair cables . 10 Table 2 Optical cables . 12 Table A.1 Table of applications 15 PD IEC/TR 62839-1:2014IEC TR 62839-1:2014 IEC 2014 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ ENVIRO

9、NMENTAL DECLARATION Part 1: Wires, cables and accessory products Specific rules FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promo

10、te international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (

11、hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non- governmental organizations liaising with the IEC also

12、 participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possib

13、le, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. Whil

14、e all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake t

15、o apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestatio

16、n of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of thi

17、s publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or ind

18、irect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for t

19、he correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. The main task of IEC technical committees is to

20、 prepare International Standards. However, a technical committee may propose the publication of a technical report when it has collected data of a different kind from that which is normally published as an International Standard, for example “state of the art“. IEC TR 62839-1, which is a technical r

21、eport, has been prepared by IEC technical committee 46: Cables, wires, waveguides, R.F. connectors, R.F. and microwave passive components and accessories. PD IEC/TR 62839-1:2014 4 IEC TR 62839-1:2014 IEC 2014 The text of this technical report is based on the following documents: Enquiry draft Report

22、 on voting 46/496/DTR 46/528/RVC Full information on the voting for the approval of this technical report can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. A list of all parts in the IEC 62839 serie

23、s, published under the general title Environmental declaration, can be found on the IEC website. The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC website under “http:/webstore.iec.ch“ in the data related to the specif

24、ic publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. A bilingual version of this publication may be issued at a later date. IMPORTANT The colour inside logo on the cover page of this publication indicates that it contains colours wh

25、ich are considered to be useful for the correct understanding of its contents. Users should therefore print this document using a colour printer. PD IEC/TR 62839-1:2014IEC TR 62839-1:2014 IEC 2014 5 ENVIRONMENTAL DECLARATION Part 1: Wires, cables and accessory products Specific rules 1 Scope This pa

26、rt of IEC 62839 specifies the PSR (product specific rules) for wires and cables used for communication, data, control and command. This PSR covers the use, installation and end-of-life stages and provides methodological precisions to PEP/PCR writing for “wires and cables and accessories” products us

27、ed for communication, data, control and command. PSR and general rules all together form the product category rules. ISO 14025:2006 establishes the principles and specifies the procedures for developing Type III environmental declaration programmes and Type III environmental declarations. It specifi

28、cally establishes the use of the ISO 14040 series of standards in the development of Type III environmental declaration programmes and Type III environmental declarations. It establishes principles for the use of environmental information, in addition to those given in ISO 14020:2000. Type III envir

29、onmental declarations as described in ISO 14025:2006 are primarily intended for use in business-to-business communication, but their use in business-to-consumer communication under certain conditions is not precluded. These environmental declarations, referred here after as PEP, follow a specific se

30、t of rules and requirements specified in product category rules declaration that are referred here after as “PEP/PCR”. Three categories of wires and cables are covered: communication and data wires and cables, which may have metal or optical fiber conductors; control and command wires and cables , w

31、hich can have metal or fiber optical conductors; accessories. This document only deals with the “wires and cables“ products. “Accessories products” are for further study. This document is primarily intended for: environment and/or product managers; LCA (life cycle assessment) experts in companies, i

32、n charge of PEP/PCR development; verifiers in charge of PEP/PCR conformity assessment in accordance with the defined rules. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references

33、, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60793 (all parts), Optical fibres PD IEC/TR 62839-1:2014 6 IEC TR 62839-1:2014 IEC 2014 IEC 60793-2-10, Optical fibres Part 2-10: Product specifications Sec

34、tional specification for category A1 multimode fibres IEC 60794 (all parts), Optical fibre cables IEC 61156 (all parts), Multicore and symmetrical pair/quad cables for digital communications IEC 61156-5, Multicore and symmetrical pair/quad cables for digital communications Part 5: Symmetrical pair/q

35、uad cables with transmission characteristics up to 1 000 MHz Horizontal floor wiring Sectional specification IEC 61156-7, Multicore and symmetrical pair/quad cables for digital communications - Part 7: Symmetrical pair cables with transmission characteristics up to 1 200 MHz - Sectional specificatio

36、n for digital and analog communication cables ISO/IEC 15018, Information technology Generic cabling for homes ISO 14020:2000, Environmental labels and declarations General principles ISO 14025:2006, Environmental labels and declarations Type III environmental declarations Principles and procedures I

37、SO 14040:2006, Environmental management Life cycle assessment Principles and framework ISO 14044, Environmental management Life cycle assessment Requirements and guidelines 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 functional unit quant

38、ified performance of a system of products intended to be used as a reference unit in a life cycle assessment SOURCE: ISO 14040:2006, 3.20, modified modified for fitting with the specific category of products that are covered in this document 3.2 product specific rules PSR set of specific rules, requ

39、irements and guidelines for developing Type III environmental declarations for a product category 3.3 product category rules PCR set of specific rules, requirements and guidelines for developing Type III environmental declarations for one or more product categories SOURCE: ISO 14025:2006, 3.5 PD IEC

40、/TR 62839-1:2014IEC TR 62839-1:2014 IEC 2014 7 3.4 product environmental profile PEP declaration indicating the environmental aspects of a product established in compliance with the PEP ecopassport program according to ISO 14025, ISO 14040 and ISO 14044 3.5 reference product product or products syst

41、em modeled in the LCA and representative of a homogeneous environmental family 3.6 reference flow measure of the outputs from processes in a given system required to fulfill the function expressed by the functional unit SOURCE: ISO 14040:2006, 3.29, modified modified for fitting with the specific ca

42、tegory of products that are covered in this document 3.7 life cycle assessment LCA compilation and evaluation of inputs, outputs and the potential environmental impacts of a product system throughout its life cycle SOURCE: ISO 14040:2006, 3.2 3.8 system boundary set of criteria that specify which el

43、ementary processes are part of a system of products SOURCE: ISO 14040:2006, 3.32, modified modified for fitting with the specific category of products that are covered in this document 4 Communication and data wires and cables 4.1 Functional unit and reference flow description Subclause 4.1 specifie

44、s for communication and data wires and cables category the chapter ”Functional unit and reference flow description” of the PEP/PCR by defining more accurately the functional unit of this product category. To define the functional unit of the communication and data wires and cables, manufacturers sha

45、ll use the following sentence. “Transmit a communication signal on 1 m according to XX protocol, YY category, during X years and a Y % use rate in accordance with the standards in force.” Lifetime and use rate match the Z application defined in Table A.1 of “Wires, cables and accessories products sp

46、ecific rules“. The determination of the number of years X depends on the application and is explained in 5.2.2. “Use phase”. To the functional unit corresponds a reference flow, expressed in metres and which includes: the reference product; the reference product packaging; PD IEC/TR 62839-1:2014 8 I

47、EC TR 62839-1:2014 IEC 2014 products and items necessary for the installation which are integrated in the field of the study. 4.2 System boundaries Overview 4.2.1 As described in the PEP/PCR, the following life cycle phases are to be recorded: the manufacturing phase: from the natural resources extr

48、action to product manufacturing and its disposal to the producers last logistic platform; the distribution phase: from the producers logistic platform until its arrival at the place of implementation; the installation phase; the use phase of the product including its use, and maintenance necessary t

49、o ensure the service ability; the end of life phase which takes into account the product end of life transportation to a treatment centre or dump. Installation phase 4.2.2 Concerning communication and data wires and cables, due to the wide range of possible installation of these products, the installation phase is excluded from the PEP/PCR perimeter. The impact determination of the installation will be performed by the PEP user