1、Telecontrol equipment and systems Part 5-604: Conformance test cases for the IEC 60870-5-104 companion standard PD IEC/TS 60870-5-604:2016 BSI Standards Publication WB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06National foreword This Published Document is the UK implementation of IEC/TS 60
2、870-5-604:2016. It supersedes DD IEC/TS 60870-5-604:2007 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee PEL/57, Power systems management and associated information exchange. A list of organizations represented on this committee can be obtained on req
3、uest to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2016. Published by BSI Standards Limited 2016 ISBN 978 0 580 92287 9 ICS 33.200 Compliance with a Briti
4、sh Standard cannot confer immunity from legal obligations. This Published Document was published under the authority of the Standards Policy and Strategy Committee on 30 June 2016. Amendments/corrigenda issued since publication Date Text affected PUBLISHED DOCUMENT PD IEC/TS 60870-5-604:2016 IEC TS
5、60870-5-604 Edition 2.0 2016-06 TECHNICAL SPECIFICATION Telecontrol equipment and systems Part 5-604: Conformance test cases for the IEC 60870-5-104 companion standard INTERNATIONAL ELECTROTECHNICAL COMMISSION ICS 33.200 ISBN 978-2-8322-3425-9 Registered trademark of the International Electrotechnic
6、al Commission Warning! Make sure that you obtained this publication from an authorized distributor. colour inside PD IEC/TS 60870-5-604:2016 2 IEC TS 60870-5-604:2016 IEC 2016 CONTENTS FOREWORD . 4 INTRODUCTION . 6 1 Scope 7 2 Normative references. 7 3 Terms and definitions 8 4 Abbreviated terms . 8
7、 5 Conformance testing for IEC 60870-5-104 8 5.1 Overview and legend . 8 5.2 Configuration parameters IEC 60870-5-104 . 10 5.3 Verification of IEC 60870-5-104 communication . 10 5.4 Conformance test procedures 51 5.5 Test results chart 88 5.6 Test results of command transmission . 95 5.6.1 General .
8、 95 5.6.2 Test results of single command transmission 96 5.6.3 Test results of double command transmission . 99 5.6.4 Test results of regulating step command transmission. 102 5.6.5 Test results of setpoint command transmission . 105 Figure 1 Test procedure . 9 Table 1 Run the Conformance Test Proce
9、dures for each of the following supported configuration parameter values . 10 Table 2 Tests on transport provider level (1 of 5) 11 Table 3 Tests on data unit identifier 16 Table 4 Verification of ASDUs for process information in monitor (normal) direction (1 of 18) . 17 Table 5 Verification of ASDU
10、s for process information in control (normal) direction (1 of 8) . 35 Table 6 Verification of ASDUs for system information in monitor (normal) direction 43 Table 7 Verification of ASDUs for system information in control (normal) direction (1 of 3) . 43 Table 8 Verification of ASDUs for parameters in
11、 control (normal) direction (1 of 2) 46 Table 9 Verification of ASDUs for file transfer (in monitor (normal) and control direction) (1 of 4) 48 Table 10 Data unit identifier conformance test procedures (1 of 2) 52 Table 11 Information object address conformance test procedures 53 Table 12 Station in
12、itialisation function conformance test procedures (1 of 3) . 54 Table 13 Redundant link conformance test procedures (1 of 3) . 57 Table 14 Cyclic data transmission function conformance test procedures 60 Table 15 Data acquisition through read function conformance test procedures 61 Table 16 Acquisit
13、ion of events function conformance test procedures . 62 Table 17 General interrogation function conformance test procedures (1 of 5) . 63 Table 18 Clock synchronisation function conformance test procedures 68 PD IEC/TS 60870-5-604:2016IEC TS 60870-5-604:2016 IEC 2016 3 Table 19 Command transmission
14、function conformance test procedures (1 of 9) . 69 Table 20 Transmission of integrated totals (telecounting) function conformance test procedures (1 of 4) . 77 Table 21 Parameter loading function conformance test procedures . 81 Table 22 Test procedure function conformance test procedures 82 Table 2
15、3 File transfer procedure function conformance test procedures (1 of 3) 83 Table 24 Additional conformance test procedures . 86 Table 25 Negative conformance test procedures . 87 Table 26 PIXIT related conformance test procedures 88 Table 27 Test results chart (1 of 7) . 89 Table 28 Test results of
16、single command transmission (1 of 3) 96 Table 29 Test results of double command transmission (1 of 3) 99 Table 30 Test results of regulating step command transmission (1 of 3) 102 Table 31 Test results of setpoint command transmission (1 of 2) . 105 PD IEC/TS 60870-5-604:2016 4 IEC TS 60870-5-604:20
17、16 IEC 2016 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ TELECONTROL EQUIPMENT AND SYSTEMS Part 5-604: Conformance test cases for the IEC 60870-5-104 companion standard FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all natio
18、nal electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical
19、 Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. In
20、ternational, governmental and non- governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The
21、 formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendatio
22、ns for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end us
23、er. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication
24、 shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent c
25、ertification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal
26、 injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative referen
27、ces cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for id
28、entifying any or all such patent rights. The main task of IEC technical committees is to prepare International Standards. In exceptional circumstances, a technical committee may propose the publication of a technical specification when the required support cannot be obtained for the publication of a
29、n International Standard, despite repeated efforts, or the subject is still under technical development or where, for any other reason, there is the future but no immediate possibility of an agreement on an International Standard. Technical specifications are subject to review within three years of
30、publication to decide whether they can be transformed into International Standards. IEC 60870-5-604, which is a technical specification, has been prepared by IEC technical committee 57: Power systems management and associated information exchange. PD IEC/TS 60870-5-604:2016IEC TS 60870-5-604:2016 IE
31、C 2016 5 This second edition cancels and replaces the first edition published in 2007. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) Resolution of ambiguities between IEC 60870-5-104:2006 and
32、IEC TS 60870-5-604:2016 (together with IEC 60870-5-104/AMD1); b) Refinement of some test cases to enhance operability between tested devices; c) Additional test cases (mainly negative test cases) added. The text of this technical specification is based on the following documents: Enquiry draft Repor
33、t on voting 57/1614/DTS 57/1683/RVC Full information on the voting for the approval of this technical specification can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. A list of all parts of IEC 60870
34、 series, published under the general title Telecontrol equipment and systems, can be found on the IEC website. The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC website under “http:/webstore.iec.ch“ in the data related
35、 to the specific publication. At this date, the publication will be transformed into an International standard, reconfirmed, withdrawn, replaced by a revised edition, or amended. A bilingual version of this publication may be issued at a later date. IMPORTANT The colour inside logo on the cover page
36、 of this publication indicates that it contains colours which are considered to be useful for the correct understanding of its contents. Users should therefore print this document using a colour printer. PD IEC/TS 60870-5-604:2016 6 IEC TS 60870-5-604:2016 IEC 2016 INTRODUCTION This part of IEC 6087
37、0, which is a technical specification, describes test cases for conformance testing of telecontrol equipment or systems using the IEC 60870-5-104 companion standard and IEC 60870-5-6, Guidelines for conformance testing for the IEC 60870-5 companion standards. PD IEC/TS 60870-5-604:2016IEC TS 60870-5
38、-604:2016 IEC 2016 7 TELECONTROL EQUIPMENT AND SYSTEMS Part 5-604: Conformance test cases for the IEC 60870-5-104 companion standard 1 Scope This part of IEC 60870, which is a technical specification, describes test cases for conformance testing of telecontrol equipment, Substation Automation System
39、s (SAS) and telecontrol systems, including front-end functions of SCADA, using the IEC 60870-5-104 companion standard and IEC 60870-5-6, Guidelines for conformance testing for the IEC 60870-5 companion standards. The use of this part of IEC 60870 facilitates interoperability by providing a standard
40、method of testing protocol implementations, but it does not guarantee interoperability of devices. It is expected that using this specification during testing will minimize the risk of non- interoperability. The goal of this part of IEC 60870 is to enable unambiguous and standardised evaluation of I
41、EC 60870-5 companion standard protocol implementations. The guidelines and conditions for the testing environment are described in IEC 60870-5-6. The detailed test cases per companion standard, containing among others mandatory and optional mandatory test cases per Basic Application Function, ASDU a
42、nd transmission procedure, will become available as a technical specification. Other functionality may need additional test cases but this is outside the scope of this part of IEC 60870. For proper testing, it is recommended to define these additional test cases. This document is such a Technical Sp
43、ecification for the mentioned companion standard. This part of IEC 60870 deals mainly with communication conformance testing; therefore other requirements, such as safety or EMC are not covered. These requirements are covered by other standards (if applicable) and the proof of compliance for these t
44、opics is done according to these standards. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of
45、the referenced document (including any amendments) applies. 1IEC 60870-5-4:1993, Telecontrol equipment and systems Part 5: Transmission protocols Section 4: Definition and coding of application information elements IEC 60870-5-5:1995, Telecontrol equipment and systems Part 5: Transmission protocols
46、Section 5: Basic application functions _ 1The base standard always takes precedence. In case of ambiguity between this technical specification and the base standards (IEC 60870-5-1 to IEC 60870-5-5, IEC 60870-5-104), this part of IEC 60870 needs to be clarified or amended. When testing, negative beh
47、aviour is not described in the base standard, the behaviour described in this document prevails and should be observed. The conformance statement produced after testing indicates any lack of conformance to either the test plan or the base standard. PD IEC/TS 60870-5-604:2016 8 IEC TS 60870-5-604:201
48、6 IEC 2016 IEC 60870-5-6:2006, Telecontrol equipment and systems Part 5-6: Guidelines for conformance testing for the IEC 60870-5 companion standards IEC 60870-5-101:2003, Telecontrol equipment and systems Part 5-101: Transmission protocols Companion standard for basic telecontrol tasks IEC 60870-5-
49、104:2006, Telecontrol equipment and systems Part 5-104: Transmission protocols Network access for IEC 60870-5-101 using standard transport profiles IETF RFC2200, Internet Official Protocol Standards 3 Terms and definitions For the purposes of this document, the terms and definitions given in IEC 60870-5-6 apply. 4 Abbreviated terms For the purposes of this document, the abbreviations given in IEC 60870-5-6 apply. 5
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1