BS ISO IEC 19798-2017 Information technology Office equipment Method for the determination of toner cartridge yield for colour printers and multifunction devices that cont.pdf

1、BS ISO/IEC 19798:2017 Information technology Office equipment Method for the determination of toner cartridge yield for colour printers and multi-function devices that contain printer components BSI Standards Publication WB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS ISO/IEC 19798:2017 B

2、RITISH STANDARD National foreword This British Standard is the UK implementation of ISO/IEC 19798:2017. It supersedes BS ISO/IEC 19798:2006 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee IST/3, IT Printers and Cartridges. A list of organizations repr

3、esented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2017. Published by BSI Standards Limited 2017 ISBN 978

4、0 580 84294 8 ICS 37.100.10 Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 January 2017. Amendments/corrigenda issued since publication Date T e x t a f f e

5、 c t e dBS ISO/IEC 19798:2017 Information technology Office equipment Method for the determination of toner cartridge yield for colour printers and multi- function devices that contain printer components Technologies de linformation quipements de bureau Mthode pour la dtermination du rendement de ca

6、rtouche de toner pour les imprimantes couleur et pour les dispositifs multifonctionnels qui contiennent des composants dimprimantes INTERNATIONAL STANDARD ISO/IEC 19798 Reference number ISO/IEC 19798:2017(E) Third edition 2017-01 ISO/IEC 2017 BS ISO/IEC 19798:2017ii ISO/IEC 2017 All rights reserved

7、COPYRIGHT PROTECTED DOCUMENT ISO/IEC 2017, Published in Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an int

8、ranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Ch. de Blandonnet 8 CP 401 CH-1214 Vernier, Geneva, Switzerland Tel. +41 22 749 01 11 Fax +41 22 749 09 47 copyrightiso.

9、org www.iso.org ISO/IEC 19798:2017(E)BS ISO/IEC 19798:2017ISO/IEC 19798:2017(E)Foreword iv Introduction v 1 Scope . 1 2 Normative references 1 3 Terms and definitions . 1 4 Test parameters and conditions . 2 4.1 Set-up 2 4.2 Sample size . 3 4.3 Print mode 3 4.4 Print environment 4 4.5 Paper 4 4.6 Ma

10、intenance 5 4.7 Test files 5 4.8 End of life . 5 5 Test methodology 6 5.1 Testing procedure . 6 5.2 Procedure for handling a defective cartridge or printer . 6 5.2.1 General 6 5.2.2 Defective cartridge . 6 5.2.3 Defective printer 7 6 Determination of the yield value and declaration 7 6.1 Determinati

11、on of the declared yield value 7 6.2 Test data reporting 8 6.3 Declaration of the yield 8 Annex A (informative) Examples of fade .10 Annex B (informative) Flow chart 11 Annex C (normative) Sample reporting form .13 Annex D (normative) Optional method for comparison of colour to ISO/IEC 19752 .17 Bib

12、liography .19 ISO/IEC 2017 All rights reserved iii Contents PageBS ISO/IEC 19798:2017ISO/IEC 19798:2017(E) Foreword ISO (the International Organization for Standardization) and IEC (the International Electrotechnical Commission) form the specialized system for worldwide standardization. National bod

13、ies that are members of ISO or IEC participate in the development of International Standards through technical committees established by the respective organization to deal with particular fields of technical activity. ISO and IEC technical committees collaborate in fields of mutual interest. Other

14、international organizations, governmental and non-governmental, in liaison with ISO and IEC, also take part in the work. In the field of information technology, ISO and IEC have established a joint technical committee, ISO/IEC JTC 1. The procedures used to develop this document and those intended fo

15、r its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .

16、org/ directives). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will

17、 be in the Introduction and/or on the ISO list of patent declarations received (see www .iso .org/ patents). Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement. For an explanation on the meaning of ISO specific terms and expr

18、essions related to conformit y assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www . i s o .org/ iso/ foreword .html. The committee responsible for this document is ISO/IEC JTC 1,

19、 Information technology, SC 28, Office equipment. This third edition cancels and replaces the second edition (ISO/IEC 19798:2007), of which it constitutes a minor revision with the following changes: The definitions for 3.1, 3.2, 3.3 and 3.4 have been aligned with ISO/IEC 19752:2016. For the sample

20、size in 4.2 at least has been inserted. 4.8 has been added as a subclause containing information previously given in notes to entry in 3.5; ISO 29142-1 has been added to the Bibliography.iv ISO/IEC 2017 All rights reservedBS ISO/IEC 19798:2017ISO/IEC 19798:2017(E) Introduction The purpose of this do

21、cument is to provide a process for determining the cartridge page yield for a given colour electrophotographic print system (i.e. all-in-one toner cartridges and toner cartridges without a photoconductor) using a standard office consumer type test suite. This test suite is not focused on printing of

22、 photographs, but is intended to be a sampling of typical office consumer pages. In the case where a cartridge set can be used in multiple printer models, only one yield test needs to be performed as long as the difference between printer models does not impact yield. NOTE A cartridge supplier can c

23、hoose to use more than one market identifier for a single physical cartridge. In this case, only one yield test is required as long as there are no differences in the cartridges other than market identifiers. This document prescribes the following: the test method that manufacturers, test labs, etc.

24、 use to determine cartridge yield; the method for determination of declared yield values from the test results; the appropriate method of describing the yield of cartridges in the documentation supplied to the consumer by the manufacturer. The cartridge yield is determined by an end of life judgment

25、, or signalled with either of two phenomena: fade caused by depletion of the useable toner in the cartridge or automatic printing stop caused by a toner out detection function. This document will be used for the measurement of one of the contributions to cost per page (CPP). This document does not d

26、irectly measure CPP, only the yield of the magenta, cyan, yellow and black toner cartridges. In most cases, these are not the only contributors to the CPP. It is beyond the scope of this document to provide a methodology for calculation of CPP. ISO/IEC 2017 All rights reserved vBS ISO/IEC 19798:2017

27、BS ISO/IEC 19798:2017Information technology Office equipment Method for the determination of toner cartridge yield for colour printers and multi-function devices that contain printer components 1 Scope The scope of this document is limited to evaluation of toner cartridge page yield for toner-contai

28、ning cartridges (i.e. all-in-one toner cartridges and toner cartridges without a photoconductor) for colour electrophotographic print systems. This document can also be applied to the printer component of any multifunctional device that has a digital input printing path, including multi-function dev

29、ices that contain electrophotographic printer components. This document is only intended for the measurement of toner cartridge page yield when printing on plain paper using cyan, magenta, yellow and black toner cartridges. No other claims can be made from this testing regarding quality, reliability

30、, etc. This document is not for use with printers whose minimum printable size is equal to or greater than A3 or for photo-only printers. NOTE 1 Application of this document for yield measurement of toner replenishment systems (i.e. toner cartridge and bottle type systems where the toner reservoir i

31、s internal to the printing system and not user- replaceable) requires some procedural modifications specifically noted herein. This document is intended for equipment used in the office space and does not apply to production volume or large format printing machines where the major cost of ownership

32、is not caused by the consumable yield measured in this document. NOTE 2 An all-in-one toner cartridge is a cartridge that includes at least: a toner containment part, a photoreceptor part and a developer part (see ISO/IEC 29142-1). 2 Normative references The following documents are referred to in th

33、e text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO/IEC 24712, Colour test pages for measu

34、rement of office equipment consumable yield 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. ISO and IEC maintain terminological databases for use in standardization at the following addresses: IEC Electropedia: available at h t t p :/ www .electr

35、opedia .org/ ISO Online browsing platform: available at h t t p :/ www .iso .org/ obp 3.1 fade phenomenon whereby a noticeable reduction in density uniformity in the bars around the sides of the diagnostic page occurs Note 1 to entry: This does not have to be a distinct gap. INTERNATIONAL ST ANDARD

36、ISO/IEC 19798:2017(E) ISO/IEC 2017 All rights reserved 1BS ISO/IEC 19798:2017ISO/IEC 19798:2017(E) Note 2 to entry: In this test, fade is defined as a noticeably lighter area, 3 mm or greater, located in the bars around the diagnostic page of the test suite. Generally, the lightening will occur para

37、llel to the paper movement direction during printing. The determination of the change in lightness is to be made referenced to the 100th page (diagnostic page) printed for each cartridge in testing. For examples of fade, consult Annex A. 3.2 shake procedure specified method to carry out shaking of a

38、 cartridge according to the user manual Note 1 to entry: If a shake procedure is used in testing, it will be noted in the report. 3.3 toner low signal generated by the printer when it has been detected that the amount of toner is such that a toner change will be required soon Note 1 to entry: It doe

39、s not indicate that the system is out of toner. 3.4 toner out signal generated by the printer when the toner in the system is depleted and the printer is incapable of reliable printing without user intervention Note 1 to entry: For the purpose of this test, the toner out signal will only be used if

40、it causes the printer to stop printing and requires toner replacement to continue printing. 3.5 end of life when the printer declares “toner out” (3.4) or when fade (3.1) is observed 3.6 individual cartridge yield value determined by counting the number of diagnostic pages (page 5 of the ISO/IEC 247

41、12 test suite) printed between cartridge installation and end of life (3.5) and multiplying by 5 Note 1 to entry: If the printer stops due to toner out (3.4) in the middle of a test page suite, the number of the diagnostic pages printed is counted. Then, the first diagnostic page of the suspended pr

42、int job is included in the subsequent cartridge yield. The number of test page suites counted may contain some pages that show visible fade (3.1). To simplify the testing, determination of end of life (3.5) is only made on the diagnostic page (page 5). 3.7 declared cartridge yield value at or below

43、the lower 90 % confidence bound as prescribed in 6.1 and 6.3 4 Test parameters and conditions 4.1 Set-up Place the printer on a horizontal surface and set up the printer according to the installation guide provided in the printer users manual. Use the most recent printer driver available from the ma

44、nufacturers website or the supplied driver with the printer. The driver version will be specified on the test report. Cartridge installation shall be completed following the instructions in the cartridge installation guide. If there is a contradiction between the printer and cartridge manuals for th

45、e cartridge installation, the cartridge manual will take precedence except if changes are recommended for printer or driver settings. If the cartridges used in testing are toner replenishment or toner bottle types, then one set of toner cartridges will be used to end of life in each printer before t

46、he start of the test. The pages printed to 2 ISO/IEC 2017 All rights reservedBS ISO/IEC 19798:2017ISO/IEC 19798:2017(E) deplete these priming cartridges do not have to be recorded and printing can be conducted at any environment. The priming cartridges are used to bring the printing system to a set

47、toner level condition. NOTE 1 The cartridges used to bring the printing system to a set toner level condition do not have to start out full. For large capacity systems, using a complete cartridge could result in tens of thousands of pages printed just to bring the system to a set condition. All imag

48、e and print quality modifiers shall be at their factory pre-set configuration for the printer and default installed condition for the driver. If the printer and driver differ, then the driver defaults shall be used. Any user selectable toner conservation modes shall be disabled during testing. If au

49、to media detection is available on the printer, it shall be disabled and media-type set to plain paper. This is to avoid inaccurate sensing of the media. For printers that default to duplex printing, the default shall be overridden and the printer be set to simplex for yield testing. If the printer under test uses an internal PDF interpreter, it is okay to use it as long as the printer defaults are set to not substitute fonts. If the internal interpreter is used, this shall be