BS PD ISO IEC TR 18781-2015 Identification cards Laundry testing of ID Cards《识别卡 ID卡的洗衣测试》.pdf

1、BSI Standards Publication Identification cards Laundry testing of ID Cards PD ISO/IEC TR 18781:2015National foreword This Published Document is the UK implementation of ISO/IEC TR 18781:2015. The UK participation in its preparation was entrusted to Technical Committee IST/17, Cards and personal iden

2、tification. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2015. Published

3、 by BSI Standards Limited 2015 ISBN 978 0 580 84562 8 ICS 97.060 Compliance with a British Standard cannot confer immunity from legal obligations. This Published Document was published under the authority of the Standards Policy and Strategy Committee on 31 October 2015. Amendments/corrigenda issued

4、 since publication Date Text affected PUBLISHED DOCUMENT PD ISO/IEC TR 18781:2015Identification cards Laundry testing of ID Cards Cartes didentification Essai en blanchisserie des cartes didentification TECHNICAL REPORT ISO/IEC TR 18781 First edition 2015-10-15 Reference number ISO/IEC TR 18781:2015

5、(E) ISO/IEC 2015 PD ISO/IEC TR 18781:2015 ii ISO/IEC 2015 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO/IEC 2015, Published in Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electron

6、ic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Ch. de Blandonnet 8 CP 401 CH-1214 Vernier

7、, Geneva, Switzerland Tel. +41 22 749 01 11 Fax +41 22 749 09 47 copyrightiso.org www.iso.org ISO/IEC TR 18781:2015(E) PD ISO/IEC TR 18781:2015 ISO/IEC TR 18781:2015(E)Foreword iv Introduction v 1 Scope .1 2 Terms and definitions .1 3 Apparatus and reagents 1 4 Test procedure 2 Bibliography 4 ISO/IE

8、C 2015 All rights reserved iii Contents Page PD ISO/IEC TR 18781:2015 ISO/IEC TR 18781:2015(E) Foreword ISO (the International Organization for Standardization) and IEC (the International Electrotechnical Commission) form the specialized system for worldwide standardization. National bodies that are

9、 members of ISO or IEC participate in the development of International Standards through technical committees established by the respective organization to deal with particular fields of technical activity. ISO and IEC technical committees collaborate in fields of mutual interest. Other internationa

10、l organizations, governmental and non-governmental, in liaison with ISO and IEC, also take part in the work. In the field of information technology, ISO and IEC have established a joint technical committee, ISO/IEC JTC 1. The procedures used to develop this document and those intended for its furthe

11、r maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of document should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). At

12、tention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO and IEC shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the I

13、ntroduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement. For an explanation on the meaning of ISO specific terms and expressions related

14、 to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information The committee responsible for this document is ISO/IEC JTC 1, Information Technology, Subcommittee SC 17,

15、Cards and personal identification.iv ISO/IEC 2015 All rights reserved PD ISO/IEC TR 18781:2015 ISO/IEC TR 18781:2015(E) Introduction Test methods developed in ISO/IEC 24789 are intended to reflect the factors affecting the life of a card in normal use. Accidental exposure such as laundering is not c

16、onsidered to be normal use. Nevertheless, many card specifiers and users are concerned that a test procedure should be drawn up and published as a recognised method. SC 17 agreed at meeting No 62 that this Technical Report was the most appropriate format for such a test. It can be used in conjunctio

17、n with tests described in the base standard. The risk of cards being laundered varies according to geographical region and national norms. In the US, for example, it is thought that most people carry their cards in a trouser pocket giving the possibility that cards are laundered with clothing. In Ja

18、pan and northern Europe, cards are mainly carried in wallets with a lower risk of laundering damage. There are a number of factors that can potentially affect cards during laundering: exposure to water plus detergent solution for a period of up to 2,5 hours; exposure to washing cycle temperatures of

19、 up to 90 C for part of that time; exposure to dryer temperatures of up to 80 C. During the process, most cards will remain within the pocket of the garment so there is likely to be some minor physical stress due to tumbling or spinning. In seeking to propose a test that may be considered representa

20、tive of the range of conditions a card may encounter, some statistics were obtained on the current trends in laundering. Globally, 38% of laundry loads are done with cold water (source: P hot wash time; total washing time. 4.3 Transfer the load to the dryer and operate the synthetics or permanent pr

21、ess cycle. Note that a drying cycle normally ends with a short cooling cycle and the load may not be fully dry. Remove the load and record the maximum card temperature after drying by reading from the temperature indicator label. This should not exceed 60 C. Remove cards from the pockets and place i

22、n a default test environment as defined in ISO/IEC 10373-1 for at least four hours before evaluation. 4.4 Compare test cards with untested cards, noting any changes in visual appearance, for example whether text is still legible and the portrait is still recognizable. If the card is damaged or warpe

23、d, check if the card is still compliant with relevant parts of ISO 7810. For cards containing an IC, magnetic stripe, or optical memory, check whether the card remains testably functional as defined in ISO/IEC 10373-1. Also, check the cards containing any other functionality tested prior to the wash

24、ing procedure. Report any visual or physical changes to the cards under test. Also, report the following: the manufacturer and model number of machine(s) used; the type and quantity of detergent and softening agent (if used); water temperature (nominal and/or actual); hot wash time; total wash cycle

25、 time; dryer cycle time; maximum card temperature after washing; maximum card temperature after drying. ISO/IEC 2015 All rights reserved 3 PD ISO/IEC TR 18781:2015 ISO/IEC TR 18781:2015(E) Bibliography 1 ISO 6059, Water quality Determination of the sum of calcium and magnesium EDTA titrimetric metho

26、d 2 ISO 6330, Textiles Domestic washing and drying procedures for textile testing 3 ISO 7810, Identification cards Physical characteristics 4 ISO/IEC 10373-1, Identification cards Test methods Part 1: General characteristics 5 ISO/IEC 24789-1, Identification cards Card service life Part 1: Applicati

27、on profiles and requirements 6 ISO/IEC 24789-2, Identification cards Card service life Part 2: Methods of evaluation 7 AAMVA DL/ID Card Design Standard, Personal Identification AAMVA North American Standard (Refers to Reference 2) 8 ANSI INCITS 322-Laundry test4 ISO/IEC 2015 All rights reserved PD I

28、SO/IEC TR 18781:2015This page deliberately left blankThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services. BSI is incorporated by Royal Charter. British Standards and other standardiza

29、tion products are published by BSI Standards Limited. British Standards Institution (BSI) BSI Group Headquarters 389 Chiswick High Road London W4 4AL UK About us We bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into s

30、tandards -based solutions. The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals. Information on standards We c

31、an provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre. Buying standards You can buy and download PDF versions of BSI publications, including British and

32、 adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team. Subscriptions Our range of subsc

33、ription services are designed to make using standards easier for you. For further information on our subscription products go to With British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24

34、/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to

35、 BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit With a Multi-User Network Licence (MUNL) you are able to host standa

36、rds publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is current. For further information, email . Revisions Our British Standards and other publications are updated by amendmen

37、t or revision. We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre. Copyright All the data, software and documentation set out in all Bri

38、tish Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use. Except a

39、s permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. Details and advice can be obtained from the

40、Copyright & Licensing Department. Useful Contacts: Customer Services Tel: +44 845 086 9001 Email (orders): Email (enquiries): Subscriptions Tel: +44 845 086 9001 Email: Knowledge Centre Tel: +44 20 8996 7004 Email: Copyright & Licensing Tel: +44 20 8996 7070 Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW