BS PD ISO TS 11619-2014 Polyurethane tubing for use primarily in pneumatic installations Dimensions and specification《气动装置中主要使用的聚氨酯管 尺寸和规范》.pdf

1、BSI Standards Publication PD ISO/TS 11619:2014 Polyurethane tubing for use primarily in pneumatic installations Dimensions and specificationPD ISO/TS 11619:2014 PUBLISHED DOCUMENT National foreword This Published Document is the UK implementation of ISO/TS 11619:2014. The UK participation in its pre

2、paration was entrusted to Technical Committee PRI/66, Rubber and plastics tubing, hoses and hose assemblies. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Use

3、rs are responsible for its correct application. The British Standards Institution 2014. Published by BSI Standards Limited 2014 ISBN 978 0 580 85118 6 ICS 23.040.20 Compliance with a British Standard cannot confer immunity from legal obligations. This Published Document was published under the autho

4、rity of the Standards Policy and Strategy Committee on 28 February 2014. Amendments issued since publication Date Text affectedPD ISO/TS 11619:2014 ISO 2014 Polyurethane tubing for use primarily in pneumatic installations Dimensions and specification Tubes en polyurthanne utiliss principalement dans

5、 les installations pneumatiques Dimensions et spcifications TECHNICAL SPECIFICATION ISO/TS 11619 First edition 2014-02-15 Reference number ISO/TS 11619:2014(E)PD ISO/TS 11619:2014ISO/TS 11619:2014(E)ii ISO 2014 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO 2014 All rights reserved. Unless oth

6、erwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address

7、 below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in SwitzerlandPD ISO/TS 11619:2014ISO/TS 11619:2014(E) ISO 2014 All rights reserved iii Co

8、ntents Page Foreword iv Introduction v 1 Scope . 1 2 Normative references 1 3 Terms and definitions . 1 4 Materials and construction . 1 5 Dimensions and tolerances . 1 5.1 Outside diameters, wall thickness and tolerances . 1 5.2 Length tolerances . 2 6 Performance requirements . 2 6.1 Hydrostatic t

9、esting at 23 C 2 C . 2 6.2 Hydrostatic testing at 60 C 2 C . 3 6.3 Maximum working pressure . 3 6.4 Minimum bend radius 3 7 Type, routine and production testing . 4 8 Marking 4 9 Recommendations for packing and storage 4 Annex A (normative) Test frequency 5 Annex B (informative) Recommended tests fo

10、r production testing 6 Bibliography 7PD ISO/TS 11619:2014ISO/TS 11619:2014(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through IS

11、O technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates c

12、losely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criter

13、ia needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements of this document may be the subject of

14、patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any trade name

15、used in this document is information given for the convenience of users and does not constitute an endorsement. For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical

16、 Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information The committee responsible for this document is ISO/TC 45, Rubber and rubber products, Subcommittee SC 1, Rubber and plastics hoses and hose assemblies.iv ISO 2014 All rights reservedPD ISO/TS 11619:2014ISO/TS 11619:

17、2014(E) Introduction This Technical Specification has been prepared to provide minimum acceptable requirements for the satisfactory performance of thermoplastic polyurethane tubing used mainly in pneumatic applications. The tubing conveys compressed air which controls and powers pneumatic systems. T

18、his Technical Specification will be revised to an International Standard when ISO 14743 has been revised and published in ISO/TC 131. ISO 2014 All rights reserved vPD ISO/TS 11619:2014PD ISO/TS 11619:2014Polyurethane tubing for use primarily in pneumatic installations Dimensions and specification WA

19、RNING Persons using this document should be familiar with normal laboratory practice. This document does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user to establish appropriate health and safety practices and to ensure complia

20、nce with any national regulatory conditions. 1 Scope This Technical Specification specifies the requirements for flexible thermoplastic polyurethane tubing conveying compressed air, for use in the ambient temperature range from 23 C to 60 C, in sizes from 3 mm to 12 mm outside diameter. Working pres

21、sure depends on the tube size and the service temperature (see Table 4). Tubing may be used with push on connectors which are specified in ISO 14743. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its applica

22、tion. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 1307, Rubber and plastics hoses Hose sizes, minimum and maximum inside diameters, and tolerances on cut-to-length hoses ISO 1402,

23、Rubber and plastics hoses and hose assemblies Hydrostatic testing ISO 10619-1:2011, Rubber and plastics hoses and tubing Measurement of flexibility and stiffness Part 1: Bending tests at ambient temperature ISO 8330, Rubber and plastics hoses and hose assemblies Vocabulary ISO 8331, Rubber and plast

24、ics hoses and hose assemblies Guidelines for selection, storage, use and maintenance 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 8330 apply. 4 Materials and construction The tubing shall be manufactured from polyester or polyether based polyureth

25、ane and shall be homogenous, and free from surface imperfections. The tubing is extruded and can be coloured to user requirements. For applications where there is moisture or water present above 40 C, polyurethane materials with good hydrolysis resistance would be required. This must be specified by

26、 the user to the supplier of the tubing. 5 Dimensions and tolerances 5.1 Outside diameters, wall thickness and tolerances The outside diameters and tolerances of tubing shall meet the requirements given in Table 1. TECHNICAL SPECIFICATION ISO/TS 11619:2014(E) ISO 2014 All rights reserved 1PD ISO/TS

27、11619:2014ISO/TS 11619:2014(E) Table 1 Outside diameters, wall thickness and tolerances Outside diameter Wall thickness Diameter mm Tolerance mm Thickness mm Tolerance mm 3 0,10 0,50 + 0,10 - 0,05 4 0,10 0,75 + 0,10 - 0,05 5 0,10 1,00 + 0,10 - 0,05 6 0,10 1,00 + 0,10 - 0,05 8 0,10 1,25 + 0,10 - 0,05

28、 8 0,10 1,00 + 0,10 - 0,05 10 0,15 1,50 + 0,15 - 0,07 10 0,15 1,00 + 0,15 - 0,05 12 0,15 2,00 + 0,15 - 0,07 5.2 Length tolerances The tolerances on cut lengths shall be in accordance with ISO 1307. 6 Performance requirements 6.1 Hydrostatic testing at 23 C 2 C When subjected to the burst pressure te

29、st specified in ISO 1402 at 23 C 2 C, tubing shall meet the requirements specified in Table 2. Table 2 Burst testing at 23 C 2 C Outside diameter mm Wall thickness mm Minimum burst pressure MPa Minimum burst pressure bar 3 0,5 5,40 54,0 4 0,75 6,23 62,3 5 1,0 6,75 67, 5 6 1,0 5,40 54,0 8 1,25 5,00 5

30、0,0 8 1,0 3,84 38,4 10 1,5 4,76 47,6 10 1,0 3,00 30,0 12 2,0 5,40 54,02 ISO 2014 All rights reservedPD ISO/TS 11619:2014ISO/TS 11619:2014(E) 6.2 Hydrostatic testing at 60 C 2 C When subjected to the burst pressure test specified in ISO 1402 at 60 C 2 C, tubing shall meet the requirements given in Ta

31、ble 3. Tests shall be conducted at 60 C in a proper temperature controlled cabinet, and compressed gas (either air or nitrogen) can be used as a burst test media. Table 3 Burst testing at 60 C 2 C Outside diameter mm Wall thickness mm Minimum burst pressure MPa Minimum burst pressure bar 3 0,5 3,46

32、34,6 4 0,75 3,98 39,8 5 1,0 4,32 43,2 6 1,0 3,45 34,5 8 1,25 3,20 32,0 8 1,0 2,47 24,7 10 1,5 3,04 30,4 10 1,0 1,92 19,2 12 2,0 3,45 34,5 6.3 Maximum working pressure The maximum working pressure shall be as specified in Table 4. Table 4 Maximum working pressures at 23 C and 60 C Outside diameter mm

33、 Wall thick- ness mm Maximum work- ing pressure at 23 C MPa Maximum work- ing pressure at 23 C bar Maximum work- ing pressure at 60 C MPa Maximum work- ing pressure at 60 C bar 3 0,5 1,35 13,5 0,86 8,6 4 0,75 1,55 15,5 0,99 9,9 5 1,0 1,68 16,8 1,08 10,8 6 1,0 1,35 13,5 0,86 8,6 8 1,25 1,25 12,5 0,80

34、 8,0 8 1,0 0,96 9,6 0,61 6,1 10 1,5 1,19 11,9 0,76 7,6 10 1,0 0,75 7, 5 0,48 4,8 12 2,0 1,35 13,5 0,86 8,6 NOTE Maximum working pressures are based on a factor of safety of 4:1 on minimum burst pressures because the main use of this tubing is for conveying compressed air. 6.4 Minimum bend radius Whe

35、n tested in accordance with ISO 10619-1:2011 method A1, the minimum bend radius shall be as specified in Table 5, and the value of T/D shall be greater than 0,9. ISO 2014 All rights reserved 3PD ISO/TS 11619:2014ISO/TS 11619:2014(E) Table 5 Minimum bending radius at 23 C Outside diameter mm Wall thi

36、ckness mm Minimum bend radius at 23 C mm 3 0,5 13 4 0,75 13 5 1,0 15 6 1,0 20 8 1,25 25 8 1,0 35 10 1,5 40 10 1,0 60 12 2,0 40 7 Type, routine and production testing For type testing and routine testing, the tests specified in Annex A shall be carried out. For production testing, the tests given in

37、Annex B are recommended. NOTE Type tests are those tests required to obtain product approval; Routine tests are those carried out on each length of tubing; and Production tests are those carried out on each production batch. 8 Marking Tubing shall be marked in characters which can be easily seen wit

38、h the naked eye, either using a contrasting indelible ink or as otherwise agreed between the supplier and the purchaser, with at least the following information: a) the manufacturers name or trade mark, e.g. XXX; b) the reference of this Technical Specification, i.e. ISO/TS 11619:2014; c) the outsid

39、e diameter and wall thickness, e.g. 6 mm 1 mm; d) the maximum working pressure at 23 C in MPa and bar, e.g. 1,35 MPa (13,5 bar) at 23 C; and e) the quarter and the last two digits of the year of manufacture, e.g. 1Q14. EXAMPLE XXX/ISO/TS 11619:2014/6 mm 1 mm/MWP1,35 MPa (13,5 bar) at 23 C/1Q14 9 Rec

40、ommendations for packing and storage The recommendations for packing and storage are given in ISO 8331.4 ISO 2014 All rights reservedPD ISO/TS 11619:2014ISO/TS 11619:2014(E) Annex A (normative) Test frequency A.1 Table A.1 gives the frequency of testing for routine tests and type tests. A.2 Type tes

41、ts are those carried out to verify that the tube meets all the requirements of this Technical Specification. A.3 Routine tests are those tests to be carried out on every manufactured length of tube. NOTE This type of tubing is normally produced with continuous outside diameter measurement and also w

42、all thickness gauging. Table A.1 Frequency of testing for routine tests and type tests Test Routine test Type test 5.1 Outside diameter X X 5.1 Wall thickness X X 6.1 Hydrostatic testing at 23 C N.A. X 6.2 Hydrostatic testing at 60 C N.A. X 6.4 Bend radius test N.A. X NOTE N.A. = Not applicable ISO

43、2014 All rights reserved 5PD ISO/TS 11619:2014ISO/TS 11619:2014(E) Annex B (informative) Recommended tests for production testing B.1 Table B.1 gives the recommended tests for production acceptance testing. B.2 Production tests are those tests to be carried out on a manufactured batch of tubing or s

44、ample of tube from a manufactured batch. B.3 A manufacturing batch is defined as a maximum of 6 000 m of tubing. Table B.1 Recommended tests for production acceptance testing Test Production test 5.1 Outside diameter X 5.1 Wall thickness X 6.1 Hydrostatic testing at 23 C X 6.2 Hydrostatic testing at

45、 60 C N.A. 6.4 Bend radius test N.A. NOTE N.A. = Not applicable6 ISO 2014 All rights reservedPD ISO/TS 11619:2014ISO/TS 11619:2014(E) Bibliography ISO 14743:2004, Pneumatic fluid power Push-in connectors for thermoplastic tubes 1) 1) Under revision. ISO 2014 All rights reserved 7PD ISO/TS 11619:2014

46、ISO/TS 11619:2014(E) ISO 2014 All rights reserved ICS 23.040.20 Price based on 7 pagesThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services. BSI is incorporated by Royal Charter. Britis

47、h Standards and other standardization products are published by BSI Standards Limited. British Standards Institution (BSI) BSI Group Headquarters 389 Chiswick High Road London W4 4AL UK About us We bring together business, industry, government, consumers, innovators and others to shape their combine

48、d experience and expertise into standards -based solutions. The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goa

49、ls. Information on standards We can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre. Buying standards You can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at bsigroup.c