BS PD ISO TS 11672-2016 Connectors for fluid power and general use Designation and nomenclature《液压动力用连接器和一般用途 名称和命名》.pdf

1、Connectors for fluid power and general use Designation and nomenclature PD ISO/TS 11672:2016 BSI Standards Publication WB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06National foreword This Published Document is the UK implementation of ISO/TS 11672:2016. The UK participation in its preparat

2、ion was entrusted by Technical Committee MCE/18, Fluid power systems and components, to Panel MCE/18/-/4, Connectors and associated components. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the nece

3、ssary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2016. Published by BSI Standards Limited 2016 ISBN 978 0 580 90317 5 ICS 01.040.23; 23.100.40 Compliance with a British Standard cannot confer immunity from legal obligations. This Pu

4、blished Document was published under the authority of the Standards Policy and Strategy Committee on 30 September 2016. Amendments/corrigenda issued since publication Date Text affected PUBLISHED DOCUMENT PD ISO/TS 11672:2016 ISO 2016 Connectors for fluid power and general use Designation and nomenc

5、lature Connecteurs pour transmissions hydrauliques et applications gnrales Dsignation et nomenclature TECHNICAL SPECIFICATION ISO/TS 11672 Reference number ISO/TS 11672:2016(E) First edition 2016-09-01 PD ISO/TS 11672:2016 ISO/TS 11672:2016(E)ii ISO 2016 All rights reserved COPYRIGHT PROTECTED DOCUM

6、ENT ISO 2016, Published in Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written

7、permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Ch. de Blandonnet 8 CP 401 CH-1214 Vernier, Geneva, Switzerland Tel. +41 22 749 01 11 Fax +41 22 749 09 47 copyrightiso.org www.iso.org PD ISO/TS 116

8、72:2016 ISO/TS 11672:2016(E)Foreword iv Introduction v 1 Scope . 1 2 Normative references 1 3 Terms and definitions . 1 4 Designation and format 1 4.1 General . 1 4.2 Connector size . 2 4.2.1 Threaded connectors and cross connectors 2 4.2.2 Flange connectors . 3 4.3 Designation for ordering parts 4

9、Annex A (normative) Index of letter symbols in alphabetical order 9 Annex B (informative) Application examples 11 Annex C (informative) Correlation of SAE dash sizes to ISO connector, tube and hose sizes 13 Bibliography .14 ISO 2016 All rights reserved iii Contents Page PD ISO/TS 11672:2016 ISO/TS 1

10、1672:2016(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject

11、for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) o

12、n all matters of electrotechnical standardization. The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be note

13、d. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying

14、any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any trade name used in this document is information given for the convenience of

15、 users and does not constitute an endorsement. For an explanation on the meaning of ISO specific terms and expressions related to conformit y assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the foll

16、owing URL: www.iso.org/iso/foreword.html. The committee responsible for this document is ISO/TC 131, Fluid power systems, Subcommittee SC 4, Connectors and similar products and components.iv ISO 2016 All rights reserved PD ISO/TS 11672:2016 ISO/TS 11672:2016(E) Introduction In fluid power systems, p

17、ower is transmitted and controlled through a fluid (liquid or gas) under pressure within an enclosed circuit. In general applications, a fluid can be conveyed under pressure. Components can be connected through their ports by connections (connectors) and conductors (tubes and hoses). Tubes are rigid

18、 conductors; hoses are flexible conductors. Annexes A and B are normative; Annex C is informative. ISO 2016 All rights reserved v PD ISO/TS 11672:2016 Connectors for fluid power and general use Designation and nomenclature 1 Scope This document collects the various designation and nomenclature schem

19、es specified in International Standards for connectors and similar products standardized by ISO/TC 131/SC 4. It establishes a uniform nomenclature structure to facilitate standardization of product names used for threaded connectors, push-in connectors, flanges, hose fittings, port plugs and quick-a

20、ction couplings. The designation and nomenclature established in this document are applicable for procurement purposes when agreed to by user and supplier. 2 Normative references The following documents are referred to in the text in such a way that some or all of their content constitutes requireme

21、nts of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. There are no normative references in this document. 3 Terms and definitions ISO and IEC maintain terminological databa

22、ses for use in standardization at the following addresses: IEC Electropedia: available at http:/ /www.electropedia.org/ ISO Online browsing platform: available at http:/ /www.iso.org/obp 4 Designation and format 4.1 General Designations use the format shown in Figure 1 when specifying a part for pro

23、curement to International Standards for connectors developed by ISO/TC 131/SC 4. Tube ends are assumed, so there is no type symbol for unions. When multiple end types are required to describe a threaded connector type, use the stud end first, when applicable (e.g. SDSWS). If there is no stud end, th

24、e description of the part shall dictate the designation order (e.g. WDRDNP for a weld-on reducing nipple). TECHNICAL SPECIFICATION ISO/TS 11672:2016(E) ISO 2016 All rights reserved 1 PD ISO/TS 11672:2016 ISO/TS 11672:2016(E) Key 1 connector name the name for the part (for example, connector, hose fi

25、tting, coupling, etc.) from the standard. 2 connector standard number the term “ISO” and the number of the relevant International Standard. 3 connector type designation the abbreviated designation consists of symbol for connector end type (Table 1) followed by, when needed, symbol for connector shap

26、e (Table 2) followed by symbol for complete connector (Table 3), if so ordered. 4 connector size see 5.2. 5 connector material symbol (Table 7) followed by seal material symbol (Table 8), where applicable. Figure 1 System for designating and specifying a part 4.2 Connector size The appropriate size

27、designator for the connector end(s) from the relevant International Standard. 4.2.1 Threaded connectors and cross connectors The following general rules shall apply: larger tube end size shall precede the smaller one for straight unions and union elbows; tube end size shall precede that of stud, hos

28、e, or other ends of the connector; male tube end shall precede female (swivel) tube end; for tee connectors, designation shall start with the size of the larger end on the run followed by the size of the branch; if the tee connector has a swivel, it shall be designated first, and on run tees the bra

29、nch size shall follow; for cross connectors, leg with the largest tube end size shall be considered the run and the other the branch; the sequence shall be run sizes (large followed by small) followed by branch sizes (large followed by small);2 ISO 2016 All rights reserved PD ISO/TS 11672:2016 ISO/T

30、S 11672:2016(E) for tube or hose ends, the size of tube or hose in millimetres is used (for 8434-1 connectors the size is followed by the duty symbol (Table 4); for stud ends with metric threads, symbol “M” followed by thread size (without pitch) followed by the duty symbol (Table 4), followed by ty

31、pe of sealing (Table 5), e.g. M14LB for M141,5 light duty stud with metal-to metal sealing. for stud ends with BSP threads, symbol “G” followed by thread size in inches followed by “A” (tolerance class), followed by duty symbol, followed by type of sealing, e.g. G1/4ASE for heavy duty stud end with

32、G1/4 BSP threads and elastomeric sealing; for stud ends with UN/UNF threads, thread size in inches (without pitch) followed by UN or UNF, as appropriate, followed by duty symbol (no sealing type is needed as only O-ring sealing is used with these threads). 4.2.2 Flange connectors For split flange cl

33、amps, FCS, the letter M if the split flange clamps are used with metric screws only, followed by a dash and the nominal size. 4.2.2.1 FCS-25 and FCSM-32 Most split flange clamps accept both inch and metric screws and shall use FCS. Those that only accept inch screws shall use FCS and those that acce

34、pt metric screws only shall use FCSM. For one-piece flange clamps, FC, the letter M if the one-piece flange clamps are used with metric screws only, followed by a dash and the nominal size e.g. FC-25 or FCM-32. Most one-piece flange clamps accept both inch and metric screws and shall use FC. Those t

35、hat only accept inch screws shall use FC and those that accept metric screws only shall use FCM For flange ports, P, followed by a dash and the nominal size and the letter M if the flange ports use metric screws e.g. P-76 or P-76M For flange heads, FH, followed by a dash and the nominal size e.g. FH

36、-76 4.2.2.2 Push-in connectors For tube ends, the outside diameter of the tubes with which they are to be connected, if all tubes are the same size, otherwise the largest and then the smallest each separated by a multiplication symbol (). For stud ends, the outside diameter of the tubes with which t

37、hey are to be connected, followed by the stud end thread designation separated by a multiplication symbol (). 4.2.2.3 Hose fittings For ISO 12151-1, ISO 12151-5 and ISO 12151-6 hose fittings, the connection size, followed by a multiplication symbol () and the hose size e.g. 1212,5. For ISO 12151-2,

38、ISO 12151-3 and ISO 12151-4 hose fittings, the duty symbol, the connection size, followed by a multiplication symbol () and the hose size e.g. L2219. 4.2.2.4 Port plugs Same as the stud ends for threaded connectors (see 5.2.1). 4.2.2.5 Quick-action couplings Since are no connector styles, only the c

39、oupling series (A, B, or C) and the nominal coupling diameter are required there. ISO 2016 All rights reserved 3 PD ISO/TS 11672:2016 ISO/TS 11672:2016(E) 4.3 Designation for ordering parts Connectors, hose fittings, port plugs, flanges, push-in fittings and quick-action couplings are designated by

40、an alphanumeric code to facilitate ordering. They are designated by the connector name and a space, followed by reference to the relevant standard (ISO XXXX), followed by a hyphen, then the type letter symbols (connector type and shape, where applicable), followed by a hyphen and followed by the siz

41、e code (tube/hose/flange end and/or thread size designators) for the ends, followed by hyphen and followed by connector and seal (if applicable) material symbols. Size designators for connector ends shall be separated by a multiplication symbol (). There shall be no spaces on either side of the hyph

42、ens or the multiplication symbol. See Tables 1 through 9 for the alpha-numeric symbols to be used. Annex A provides an index of the letter symbols used in alphabetical order. Annex B provides examples of how the designation system is applied. Annex C provides correlation of SAE dash sizes to ISO con

43、nector, tube and hose sizes. Table 1 Letter symbols to be used in designating connector types for fluid power and general use Connector type Letter symbol Tube connectors Hose fittings Threaded Flange Push-in Banjo BJ 14743 Bulkhead BH 8434-1 8434-2 8434-3 8434-6 14743 Braze-on BR 8434-1 8434-3 Cap

44、CP 8434-1 8434-2 8434-3 Plug PL 8434-1 8434-2 8434-3 14743 Port P 6162-1 6162-2 14743 Reducer Reducer with nut Reducer without nut RD RDA RDB 8434-1 8434-2 8434-6 8434-3 8434-3 Stud SD 8434-1 8434-2 8434-3 8434-6 14743 12151-4 Swivel With sealing surface not exposed With sealing surface exposed SW S

45、WA SWB 8434-1 8434-2 8434-6 8434-3 8434-3 14743 12151-2 12151-5 12151-6 12151-1 12151-1 Swivel with O-ring SWO 8434-1 Swivel bulkhead SWBH 147434 ISO 2016 All rights reserved PD ISO/TS 11672:2016 ISO/TS 11672:2016(E) Connector type Letter symbol Tube connectors Hose fittings Threaded Flange Push-in

46、Swivel port SWP 14743 Tube end TE 14743 Weld-on / Weld-in WD 8434-1 8434-3 Table 2 Letter symbols to be used in designating shapes of connectors for fluid power and general use Shape Letter symbol Tube connectors Hose fittings Threaded Push-in Branch tee BT 8434-1 8434-2 8434-3 14743 90 elbow E 8434

47、-1 8434-2 8434-3 8434-6 14743 12151-1 12151-2 12151-3 12151-4 12151-5 12151-6 22,5 elbow E22 12151-3 30 elbow E30 12151-3 45 elbow E45 12151-1 12151-2 12151-3 12151-5 12151-6 60 elbow E60 12151-3 67, 5 elbow E67 12151-3 Cross K 8434-1 8434-2 8434-3 14743 Run tee RT 8434-1 8434-2 8434-3 14743 Straigh

48、t S 8434-1 8434-2 8434-3 14743 12151-1 12151-2 12151-3 12151-4 12151-5 12151-6 Tee T 8434-1 8434-2 8434-3 14743 Y shape Y 14743Table 1 (continued) ISO 2016 All rights reserved 5 PD ISO/TS 11672:2016 ISO/TS 11672:2016(E) Table 3 Letter symbols to be used in designating types of components of connecto

49、rs for fluid power and general use Type of connector component Letter symbol Tube connectors Threaded Flange Cutting ring CR 8434-1 One-piece flange clamp FC 6162-1 6162-2 Split flange clamp pair FCS 6162-1 6162-2 Flange head FH 6162-1 6162-2 Locknut LN 8434-1 8434-2 8434-3 Sleeve: For metric tube For inch tube SL MSL ISL 8434-2 8434-3 8434-2 8434-3 Nut Standard strength nut High strength nut N NA NB 8434-1 8434-2 8434-3 8434-3 Nipple For metric tube For inch tube NP MNP INP