1、BSI Standards Publication Cutting tool data representation and exchange Part 303: Creation and exchange of 3D models Solid end mills PD ISO/TS 13399-303:2016National foreword This Published Document is the UK implementation of ISO/TS 13399-303:2016. The UK participation in its preparation was entrus
2、ted to Technical Committee MTE/18, Tools tips and inserts for cutting applications. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for it
3、s correct application. The British Standards Institution 2016. Published by BSI Standards Limited 2016 ISBN 978 0 580 92390 6 ICS 25.100.01; 35.240.50 Compliance with a British Standard cannot confer immunity from legal obligations. This Published Document was published under the authority of the St
4、andards Policy and Strategy Committee on 29 February 2016. Amendments/corrigenda issued since publication Date Text affected PUBLISHED DOCUMENT PD ISO/TS 13399-303:2016 ISO 2016 Cutting tool data representation and exchange Part 303: Creation and exchange of 3D models Solid end mills Reprsentation e
5、t change des donnes relatives aux outils coupants Partie 303: Cration et change de modles 3D Fraises cylindriques deux tailles monobloc TECHNICAL SPECIFICATION ISO/TS 13399-303 Reference number ISO/TS 13399-303:2016(E) First edition 2016-02-01 PD ISO/TS 13399-303:2016 ISO/TS 13399-303:2016(E)ii ISO
6、2016 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO 2016, Published in Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on t
7、he internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Ch. de Blandonnet 8 CP 401 CH-1214 Vernier, Geneva, Switzerland Tel. +41 22 749 01 11 Fax +41 22 74
8、9 09 47 copyrightiso.org www.iso.org PD ISO/TS 13399-303:2016 ISO/TS 13399-303:2016(E)Foreword v Introduction vii 1 Scope . 1 2 Normative references 1 3 Starting elements, coordinate systems, planes 2 3.1 General . 2 3.2 Reference system 2 3.3 Coordinate system at the cutting part 3 3.4 Planes 3 3.5
9、 Cutting reference point (CRP) 4 4 Design of the model . 5 4.1 General . 5 4.2 Necessary parameters for the connection interface feature . 5 5 Non-centre cutting end mill 5 5.1 General . 5 5.2 Necessary properties . 6 5.3 Geometry of the non-cutting part inclusive of the connection 7 5.4 Geometry of
10、 the cutting part . 7 5.5 Complete non-centre cutting end mill 8 6 Centre cutting end mill . 9 6.1 General . 9 6.2 Necessary properties . 9 6.3 Geometry of the non-cutting part inclusive of the connection 9 6.4 Geometry of the cutting part 10 6.5 Complete centre cutting end mill .10 7 Angular end mi
11、ll (V-groove) 11 7.1 General 11 7.2 Necessary properties 11 7.3 Geometry of the non-cutting part inclusive of the connection .11 7.4 Geometry of the cutting part 12 7.5 V-groove end mill, complete .13 8 Dovetail end mill 13 8.1 General 13 8.2 Necessary properties 13 8.3 Geometry of the non-cutting p
12、art inclusive of the connection .13 8.4 Geometry of the cutting part 14 8.5 Complete dovetail end mill, complete 15 9 T-slot end mill .15 9.1 General 15 9.2 Necessary properties 15 9.3 Geometry of the non-cutting part inclusive of the connection .15 9.4 Geometry of the cutting part 16 9.5 Complete T
13、-slot end mill 16 10 Ball-nosed end mill .17 10.1 General 17 10.2 Necessary properties 17 10.3 Geometry of the non-cutting part inclusive of the connection .18 10.4 Geometry of the cutting part 18 10.5 Complete ball-nosed end mill18 11 Die end mill .19 ISO 2016 All rights reserved iii Contents Page
14、PD ISO/TS 13399-303:2016 ISO/TS 13399-303:2016(E)11.1 General 19 11.2 Necessary properties 19 11.3 Geometry of the non-cutting part inclusive of the connection .20 11.4 Geometry of the cutting part 20 11.5 Complete die end mill 20 12 C onca v e r ounded pr ofile end mill .21 12.1 General 21 12.2 Nec
15、essary properties 21 12.3 Geometry of the non-cutting part inclusive of the connection .21 12.4 Geometry of the cutting part 21 12.5 Complete concave rounded profile end mill .22 13 Thread end mill 23 13.1 General 23 13.2 Necessary properties 23 13.3 Geometry of the non-cutting part inclusive of the
16、 connection .24 13.4 Geometry of the cutting part 24 13.5 Complete thread end mill .24 14 Cutting stylus .25 14.1 General 25 14.2 Necessary properties 25 14.3 Geometry of the non-cutting part inclusive of the connection .26 14.4 Geometry of the cutting part 26 14.5 Complete cutting stylus, complete
17、26 15 Thread end mill with drilling part 27 15.1 General 27 15.2 Necessary properties 27 15.3 Geometry of the non-cutting part inclusive of the connection .28 15.4 Geometry of the cutting part 28 15.5 Complete thread end mill with drilling part .28 16 Design of details .29 16.1 Basics for modelling
18、29 16.2 Contact/clamping surfaces Orientation 29 16.3 Chamfers, rounding, others .29 17 Attributes of surfaces Visualization of the model features 29 18 Structure of the design elements (tree of model) .30 19 Data exchange model 30 Annex A (informative) Information about nominal dimensions 32 Biblio
19、graphy .33 iv ISO 2016 All rights reserved PD ISO/TS 13399-303:2016 ISO/TS 13399-303:2016(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried
20、 out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO
21、 collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different
22、approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements of this document may be
23、the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).
24、Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement. For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles i
25、n the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information The committee responsible for this document is ISO/TC 29, Small tools. ISO/TS 13399 consists of the following parts, under the general title Cutting tool data representation and exchange: Part 1: Over
26、view, fundamental principles and general information model Part 2: Reference dictionary for the cutting items Technical Specification Part 3: Reference dictionary for tool items Technical Specification Part 4: Reference dictionary for adaptive items Technical Specification Part 5: Reference dictiona
27、ry for assembly items Technical Specification Part 50: Reference dictionary for reference systems and common concepts Technical Specification Part 60: Reference dictionary for connection systems Technical Specification Part 80: Creation and exchange of 3D models Overview and principles Technical Spe
28、cification Part 100: Definitions, principles and methods for reference dictionaries Technical Specification Part 150: Usage guidelines Technical Specification Part 201: Creation and exchange of 3D models Regular inserts Technical Specification Part 202: Creation and exchange of 3D models Irregular i
29、nserts Technical Specification Part 203: Creation and exchange of 3D models Replaceable inserts for drilling Technical Specification Part 204: Creation and exchange of 3D models Inserts for reaming Technical Specification Part 301: Concept for the design of 3D models based on properties according to
30、 ISO/TS 13399-3: Modelling of thread-cutting taps, thread-forming taps and thread-cutting dies Technical Specification ISO 2016 All rights reserved v PD ISO/TS 13399-303:2016 ISO/TS 13399-303:2016(E) Part 302: Concept for the design of 3D models based on properties according to ISO/TS 13399-3: Model
31、ling of solid drills and countersinking tools Technical Specification Part 303: Concept for the design of 3D models based on properties according to ISO/TS 13399-3: Modelling of end mills with solid cutting edges Technical Specification Part 304: Concept for the design of 3D models based on properti
32、es according to ISO/TS 13399-3: Modelling of milling cutters with arbor hole and solid cutting edges Technical Specification Part 307: Creation and exchange of 3D models End mills for indexable inserts Technical Specification Part 308: Creation and exchange of 3D models Milling cutters with arbor ho
33、le for indexable inserts Technical Specification Part 309: Creation and exchange of 3D models Tool holders for indexable inserts Technical Specification Part 311: Creation and exchange of 3D models Solid reamers Technical Specification Part 312: Creation and exchange of 3D models Reamers for indexab
34、le inserts Technical Specification Part 401: Creation and exchange of 3D models Converting, extending and reducing adaptive items Technical Specification Part 405: Creation and exchange of 3D models Collets Technical Specification The following parts are under preparation: Part 70: Graphical data la
35、yout Layer settings for tool designs Technical Specification Part 71: Graphical data layout Creation of documents for the standardized data exchange Graphical product information Technical Specification Part 72: Creation of documents for the standardized data exchange Definition of properties for dr
36、awing header and their XML-data exchange Technical Specification Part 305: Creation and exchange of 3D models Modular tooling systems with adjustable cartridges for boring Technical Specification Part 310: Creation and exchange of 3D models T urning tools with carbide tips Technical Specificationvi
37、ISO 2016 All rights reserved PD ISO/TS 13399-303:2016 ISO/TS 13399-303:2016(E) Introduction This part of ISO/TS 13399 defines the concept, the terms and the definitions on how to design simplified 3D models of milling cutters with arbors hole for indexable inserts that can be used for NC- programmin
38、g, simulation of the manufacturing processes and the determination of collision within machining processes. It is not intended to standardize the design of the cutting tool itself. A cutting tool is used in a machine to remove material from a workpiece by a shearing action at the cutting edges of th
39、e tool. Cutting tool data that can be described by ISO/TS 13399 (all parts) include, but are not limited to, everything between the workpiece and the machine tool. Information about inserts, solid tools, assembled tools, adaptors, components and their relationships can be represented by ISO/TS 13399
40、 (all parts). The increasing demand providing the enduser with 3D models for the purposes defined above is the basis for the development of this series of International Standards. The objective of this International Standard is to provide the means to represent the information that describes cutting
41、 tools in a computer sensible form that is independent from any particular computer system. The representation will facilitate the processing and exchange of cutting tool data within and between different software systems and computer platforms and support the application of this data in manufacturi
42、ng planning, cutting operations and the supply of tools. The nature of this description makes it suitable not only for neutral file exchange, but also as a basis for implementing and sharing product databases and for archiving. The methods that are used for these representations are those developed
43、by ISO/TC 184/SC 4 for the representation of product data by using standardized information models and reference dictionaries. Definitions and identifications of dictionary entries are defined by means of standard data that consist of instances of the EXPRESS entity data types defined in the common
44、dictionary schema, resulting from a joint effort between ISO/TC 184/SC 4 and IEC/TC 3/SC 3D, and in its extensions defined in ISO 13584-24 and ISO 13584-25. ISO 2016 All rights reserved vii PD ISO/TS 13399-303:2016 Cutting tool data representation and exchange Part 303: Creation and exchange of 3D m
45、odels Solid end mills 1 Scope This part of ISO/TS 13399 specifies a concept for the design of tool items, limited to solid (non-indexable) end mills, with the usage of the related properties and domains of values. This part of ISO/TS 13399 specifies a common way of design simplified models that cont
46、ain the following: definitions and identifications of the design features of solid (non-indexable) end mills, with a link to the properties used; definitions and identifications of the internal structure of the 3D model that represents features and properties of solid (non-indexable) end mills. The
47、following are outside the scope of this part of ISO/TS 13399: applications where these standard data may be stored or referenced; creation and exchange of simplified 3D models for cutting tools; creation and exchange of simplified 3D models for cutting items; creation and exchange of simplified 3D m
48、odels for other tool items not being described in the scope of this part of ISO/TS 13399; creation and exchange of simplified 3D models for adaptive items; creation and exchange of simplified 3D models for assembly items and auxiliary items. 2 Normative references The following documents, in whole o
49、r in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO/TS 13399-3, Cutting tool data representation and exchange Part 3: Reference dictionary for tool items ISO
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1