1、BSI Standards Publication PD ISO/TS 13399-309:2016 Cutting tool data representation and exchange Part 309: Creation and exchange of 3D models Tool holders for indexable insertsPD ISO/TS 13399-309:2016 PUBLISHED DOCUMENT National foreword This Published Document is the UK implementation of ISO/TS 133
2、99-309:2016. The UK participation in its preparation was entrusted to Technical Committee MTE/18, Tools tips and inserts for cutting applications. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the n
3、ecessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2016. Published by BSI Standards Limited 2016 ISBN 978 0 580 83599 5 ICS 25.100.01; 35.240.50 Compliance with a British Standard cannot confer immunity from legal obligations. This
4、 Published Document was published under the authority of the Standards Policy and Strategy Committee on 31 March 2016. Amendments issued since publication Date Text affectedPD ISO/TS 13399-309:2016 ISO 2016 Cutting tool data representation and exchange Part 309: Creation and exchange of 3D models To
5、ol holders for indexable inserts Reprsentation et change des donnes relatives aux outils coupants Partie 309: Cration et change de modles 3D Porte outil plaquette amovible TECHNICAL SPECIFICATION ISO/TS 13399-309 Reference number ISO/TS 13399-309:2016(E) First edition 2016-03-01PD ISO/TS 13399-309:2
6、016ISO/TS 13399-309:2016(E)ii ISO 2016 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO 2016, Published in Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, inclu
7、ding photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Ch. de Blandonnet 8 CP 401 CH-1214 Vernier, Geneva, Switzerland T
8、el. +41 22 749 01 11 Fax +41 22 749 09 47 copyrightiso.org www.iso.orgPD ISO/TS 13399-309:2016ISO/TS 13399-309:2016(E)Foreword vi Introduction viii 1 Scope . 1 2 Normative references 1 3 Starting elements, coordinate systems, planes 2 3.1 General . 2 3.2 Reference system (PCS primary coordinate syst
9、em) 2 3.3 Tool item position . 2 3.3.1 Prismatic tool position . . 3 3.3.2 Round tool position . 3 3.4 Planes 4 3.5 Cutting reference point (CRP) 5 3.6 Design of the pocket seat . 8 3.7 Adjustment coordinate system on workpiece side .12 3.7.1 General.12 3.7.2 Designation of the coordinate system wor
10、kpiece side 12 4 Design of the model 14 4.1 Necessary parameters for the connection interface feature 14 4.2 Necessary properties for insert and pocket seat 15 4.2.1 General.15 4.2.2 Properties for equilateral, equiangular and equilateral, non- equiangular inserts .15 4.2.3 Properties for non-equila
11、teral, equiangular and non-equilateral, non- equiangular inserts .15 4.2.4 Properties for round inserts .16 4.2.5 Design of the pocket seat feature16 5 Tool holder for longitudinal and transversal turning 17 5.1 General 17 5.2 Necessary properties 17 5.3 Basic geometry .18 5.4 Turning tool with pock
12、et seat and top surface offset .21 5.5 Turning tool assembly .21 5.6 Boring bar body .22 6 Turning tool for external threading 24 6.1 General 24 6.2 Necessary properties 24 6.3 Basic geometry .25 6.4 Turning tool with pocket seat and top surface offset .25 6.5 Turning tool assembly .26 7 Boring bar
13、for internal threading 27 7.1 General 27 7.2 Necessary properties 27 7.3 Basic geometry .28 7.4 Boring bar with pocket seat and top surface offset 29 7.5 Boring bar assembly 30 8 Turning tool for OD grooving and parting 30 8.1 General 30 8.2 Necessary properties 30 8.3 Basic geometry .32 8.4 Groovin
14、g tool with pocket seat and top surface offset 33 8.5 Grooving and cut-off tool assembly .33 ISO 2016 All rights reserved iii Contents PagePD ISO/TS 13399-309:2016ISO/TS 13399-309:2016(E)9 Boring bar for ID grooving 34 9.1 General 34 9.2 Necessary properties 34 9.3 Basic geometry .35 9.4 Boring bar
15、with pocket seat and top surfaces .36 9.5 Grooving boring bar assembly .37 10 Pull back boring bar .37 10.1 General 37 10.2 Necessary properties 38 10.3 Basic geometry .38 10.4 Boring bar with pocket seat and top surfaces .39 10.5 Pull back boring bar assembly .39 11 System tool for external turning
16、 .40 11.1 General 40 11.2 Necessary properties 40 11.3 Basic geometry .41 11.4 System tool with pocket seat and top surfaces 41 11.5 Assembly of system tool for external turning .42 12 System tool for external threading .43 12.1 General 43 12.2 Necessary properties 43 12.3 Basic geometry .44 12.4 Sy
17、stem tool with pocket seat and top surfaces 44 12.5 Assembly of a system tool for external threading .44 13 System tool for internal turning 44 13.1 General 44 13.2 Necessary properties 45 13.3 Basic geometry .45 13.4 System tool with pocket seat and top surfaces 45 13.5 System tool for internal tur
18、ning assembly .45 14 System tool for internal threading 46 14.1 General 46 14.2 Necessary properties 46 14.3 Basic geometry .46 14.4 System tool with pocket seat and top surfaces 46 14.5 System tool for internal threading assembly .46 15 System tool for OD grooving and/or cut-off 47 15.1 General 47
19、15.2 Necessary properties 47 15.3 Basic geometry .48 15.4 Grooving tool with pocket seat and top surface offset 48 15.5 System tool for OD grooving and parting assembly .48 16 System tool for ID grooving 49 16.1 General 49 16.2 Necessary properties 49 16.3 Basic geometry .49 16.4 Grooving tool with
20、pocket seat and top surface offset 49 16.5 System tool for ID grooving assembly 49 17 Pull back system tool 50 17.1 General 50 17.2 Necessary properties 50 17.3 Basic geometry .50 17.4 System tool with pocket seat and top surfaces 51 17.5 Pull back system tool assembly .51 iv ISO 2016 All rights res
21、ervedPD ISO/TS 13399-309:2016ISO/TS 13399-309:2016(E)18 System tool, neutral design for OD turning 51 18.1 General 51 18.2 Necessary properties 51 18.3 Basic geometry .52 18.4 System tool with pocket seat and top surfaces 52 18.5 System tool, neutral design for OD turning assembly 52 19 Design of de
22、tails .52 19.1 Basics for modelling 52 19.2 Fixing threads for inserts 52 19.3 Contact surfaces/drive keys Orientation .52 19.4 Chamfers and roundings .52 20 Attributes of surfaces Visualization of the model features 52 21 Structure of the design elements (tree of model) .53 22 Data exchange model 5
23、4 Annex A (normative) Mirror planes for left-handed tools 56 Annex B (informative) Information about nominal dimensions 57 Bibliography .58 ISO 2016 All rights reserved vPD ISO/TS 13399-309:2016ISO/TS 13399-309:2016(E) Foreword ISO (the International Organization for Standardization) is a worldwide
24、federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that c
25、ommittee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The procedures used to develop this documen
26、t and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives,
27、 Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development
28、of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement. For an explanation on the meaning of ISO specif
29、ic terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information The committee responsible for this document is ISO/TC 29, Small tools. ISO
30、/TS 13399 consists of the following parts, under the general title Cutting tool data representation and exchange: Part 1: Overview, fundamental principles and general information model Part 2: Reference dictionary for the cutting items Technical Specification Part 3: Reference dictionary for tool it
31、ems Technical Specification Part 4: Reference dictionary for adaptive items Technical Specification Part 5: Reference dictionary for assembly items Technical Specification Part 50: Reference dictionary for reference systems and common concepts Technical Specification Part 60: Reference dictionary fo
32、r connection systems Technical Specification Part 80: Creation and exchange of 3D models Overview and principles Technical Specification Part 100: Definitions, principles and methods for reference dictionaries Technical Specification Part 150: Usage guidelines Technical Specification Part 201: Creat
33、ion and exchange of 3D models Regular inserts Technical Specification Part 202: Creation and exchange of 3D models Irregular inserts Technical Specification Part 203: Creation and exchange of 3D models Replaceable inserts for drilling Technical Specification Part 204: Creation and exchange of 3D mod
34、els Inserts for reaming Technical Specification Part 301: Concept for the design of 3D models based on properties according to ISO/TS 133993: Modelling of thread cutting taps, thread forming taps and thread cutting dies Technical Specificationvi ISO 2016 All rights reservedPD ISO/TS 13399-309:2016IS
35、O/TS 13399-309:2016(E) Part 302: Concept for the design of 3D models based on properties according to ISO/TS 133993: Modelling of solid drills and countersinking tools Technical Specification Part 303: Concept for the design of 3D models based on properties according to ISO/TS 133993: Modelling of e
36、nd mills with solid cutting edges Technical Specification Part 304: Concept for the design of 3D models based on properties according to ISO/TS 133993: Modelling of milling cutters with arbor hole and solid cutting edges Technical Specification Part 307: Creation and exchange of 3D models End mills
37、for indexable inserts Technical Specification Part 308: Creation and exchange of 3D models Milling cutters with arbor hole for indexable inserts Technical Specification Part 309: Creation and exchange of 3D models Tool holders for indexable inserts Technical Specification Part 311: Creation and exch
38、ange of 3D models Solid reamers Technical Specification Part 312: Creation and exchange of 3D models Reamers for indexable inserts Technical Specification Part 401: Creation and exchange of 3D models Converting, extending and reducing adaptive items Technical Specification Part 405: Creation and exc
39、hange of 3D models Collets Technical Specification The following parts are under preparation: Part 70: Graphical data layout Layer settings for tool designs Technical Specification Part 71: Graphical data layout Creation of documents for the standardized data exchange Graphical product information T
40、echnical Specification Part 72: Creation of documents for the standardized data exchange Definition of properties for drawing header and their XML data exchange Technical Specification Part 305: Creation and exchange of 3D models Modular tooling systems with adjustable cartridges for boring Technica
41、l Specification Part 310: Creation and exchange of 3D models T urning tools with carbide tips Technical Specification ISO 2016 All rights reserved viiPD ISO/TS 13399-309:2016ISO/TS 13399-309:2016(E) Introduction This part of ISO/TS 13399 defines the concept, the terms and the definitions on how to d
42、esign simplified 3D models of tool holders for indexable inserts that can be used for NC-programming, simulation of the manufacturing processes and the determination of collision within these processes. It is not intended to standardize the design of the cutting tool itself. A cutting tool is used i
43、n a machine to remove material from a workpiece by a shearing action at the cutting edges of the tool. Cutting tool data that can be described by ISO/TS 13399 (all parts) include, but are not limited to, everything between the workpiece and the machine tool. Information about inserts, solid tools, a
44、ssembled tools, adaptors, components and their relationships can be represented by ISO/TS 13399 (all parts). The increasing demand providing the end user with 3D models for the purposes defined above is the basis for the development of this series of International Standards. The objective of this In
45、ternational Standard is to provide the means to represent the information that describes cutting tools in a computer sensible form that is independent from any particular computer system. The representation will facilitate the processing and exchange of cutting tool data within and between different
46、 software systems and computer platforms and support the application of this data in manufacturing planning, cutting operations and the supply of tools. The nature of this description makes it suitable not only for neutral file exchange, but also as a basis for implementing and sharing product datab
47、ases and for archiving. The methods that are used for these representations are those developed by ISO/TC 184/SC 4 for the representation of product data by using standardized information models and reference dictionaries. Definitions and identifications of dictionary entries are defined by means of
48、 standard data that consist of instances of the EXPRESS entity data types defined in the common dictionary schema, resulting from a joint effort between ISO/TC 184/SC 4 and IEC/TC 3/SC 3D and in its extensions defined in ISO 13584-24 and ISO 13584-25.viii ISO 2016 All rights reservedPD ISO/TS 13399-
49、309:2016TECHNICAL SPECIFICATION ISO/TS 13399-309:2016(E) Cutting tool data representation and exchange Part 309: Creation and exchange of 3D models Tool holders for indexable inserts 1 Scope This part of ISO/TS 13399 specifies a concept for the design of turning tools for indexable inserts, together with the usage of the related properties and domains of values. This pa
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1