1、BSI Standards Publication PD ISO/TS 13399-401:2016 Cutting tool data representation and exchange Part 401: Creation and exchange of 3D models Converting, extending and reducing adaptive itemsPD ISO/TS 13399-401:2016 PUBLISHED DOCUMENT National foreword This Published Document is the UK implementatio
2、n of ISO/TS 13399-401:2016. The UK participation in its preparation was entrusted to Technical Committee MTE/18, Tools tips and inserts for cutting applications. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to in
3、clude all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2016. Published by BSI Standards Limited 2016 ISBN 978 0 580 84133 0 ICS 25.100.01; 35.240.50 Compliance with a British Standard cannot confer immunity from legal ob
4、ligations. This Published Document was published under the authority of the Standards Policy and Strategy Committee on 31 March 2016. Amendments issued since publication Date Text affectedPD ISO/TS 13399-401:2016 ISO 2016 Cutting tool data representation and exchange Part 401: Creation and exchange
5、of 3D models Converting, extending and reducing adaptive items Reprsentation et change des donnes relatives aux outils coupants Partie 401: Cration et change de modles 3D Conversion, extension et rduction relatif aux attachements TECHNICAL SPECIFICATION ISO/TS 13399-401 Reference number ISO/TS 13399
6、-401:2016(E) First edition 2016-02-15PD ISO/TS 13399-401:2016ISO/TS 13399-401:2016(E)ii ISO 2016 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO 2016, Published in Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in
7、 any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Ch. de
8、Blandonnet 8 CP 401 CH-1214 Vernier, Geneva, Switzerland Tel. +41 22 749 01 11 Fax +41 22 749 09 47 copyrightiso.org www.iso.orgPD ISO/TS 13399-401:2016ISO/TS 13399-401:2016(E)Foreword v Introduction vii 1 Scope . 1 2 Normative references 1 3 Starting elements, coordinate systems, planes 2 3.1 Gener
9、al . 2 3.2 Reference system (PCS primary coordinate system) 2 3.3 Adaptive item position . 3 3.3.1 General 3 3.3.2 Prismatic adaptive position 3 3.3.3 Round adaptive position . 3 3.4 Adjustment coordinate system at workpiece side . 3 3.4.1 General 3 3.4.2 Designation of coordinate systems at workpie
10、ce side 3 3.4.3 Arrangement of coordinate system workpiece side 4 3.5 Mounting coordinate system 5 3.6 Planes 6 4 Design of the model . 6 4.1 General . 6 4.2 Necessary properties for the connection interface feature 7 5 Converter, rotationally symmetric . 7 5.1 General . 7 5.2 Necessary properties .
11、 8 5.3 Basic geometry 8 5.4 Connection on workpiece side .10 5.5 Rotational symmetric converter, complete 11 6 Converter, stationary .12 6.1 General 12 6.2 Necessary properties 12 6.3 Basic geometry .13 6.4 Connection on workpiece side .15 6.5 Stationary converter, complete 15 7 Extender .16 7.1 Gen
12、eral 16 7.2 Necessary properties 16 7.3 Basic geometry .16 7.4 Connection on workpiece side .17 7.5 Extender, complete .18 8 Reducer, primary design .18 8.1 General 18 8.2 Necessary properties 19 8.3 Basic geometry .19 8.4 Connection on workpiece side .20 8.5 Reducer, primary design, complete 21 9 R
13、educer, reverse design .21 9.1 General 21 9.2 Necessary properties 22 9.3 Basic geometry .22 9.4 Connection on workpiece side .23 9.5 Reducer, reverse design, complete 23 ISO 2016 All rights reserved iii Contents PagePD ISO/TS 13399-401:2016ISO/TS 13399-401:2016(E)10 Design of details .24 10.1 Basic
14、s for modelling 24 10.2 Contact surfaces, driving features Orientation .24 10.3 Chamfers and roundings .24 11 Attributes of surfaces Visualization of the model features 25 12 Structure of the design elements (tree of model) .25 13 Data exchange model 26 Bibliography .27 iv ISO 2016 All rights reserv
15、edPD ISO/TS 13399-401:2016ISO/TS 13399-401:2016(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Eac
16、h member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the Internation
17、al Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different
18、 types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall no
19、t be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any trade name used in this document is in
20、formation given for the convenience of users and does not constitute an endorsement. For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) se
21、e the following URL: Foreword - Supplementary information The committee responsible for this document is ISO/TC 29, Small tools. ISO/TS 13399 consists of the following parts, under the general title Cutting tool data representation and exchange: Part 1: Overview, fundamental principles and general i
22、nformation model Part 2: Reference dictionary for the cutting items Technical Specification Part 3: Reference dictionary for tool items Technical Specification Part 4: Reference dictionary for adaptive items Technical Specification Part 5: Reference dictionary for assembly items Technical Specificat
23、ion Part 50: Reference dictionary for reference systems and common concepts Technical Specification Part 60: Reference dictionary for connection systems Technical Specification Part 80: Creation and exchange of 3D models Overview and principles Technical Specification Part 100: Definitions, principl
24、es and methods for reference dictionaries Technical Specification Part 150: Usage guidelines Technical Specification Part 201: Creation and exchange of 3D models Regular inserts Technical Specification Part 202: Creation and exchange of 3D models Irregular inserts Technical Specification Part 203: C
25、reation and exchange of 3D models Replaceable inserts for drilling Technical Specification Part 204: Creation and exchange of 3D models Inserts for reaming Technical Specification Part 301: Concept for the design of 3D models based on properties according to ISO/TS 133993: Modelling of thread cuttin
26、g taps, thread forming taps and thread cutting dies Technical Specification ISO 2016 All rights reserved vPD ISO/TS 13399-401:2016ISO/TS 13399-401:2016(E) Part 302: Concept for the design of 3D models based on properties according to ISO/TS 133993: Modelling of solid drills and countersinking tools
27、Technical Specification Part 303: Concept for the design of 3D models based on properties according to ISO/TS 133993: Modelling of end mills with solid cutting edges Technical Specification Part 304: Concept for the design of 3D models based on properties according to ISO/TS 133993: Modelling of mil
28、ling cutters with arbor hole and solid cutting edges Technical Specification Part 307: Creation and exchange of 3D models End mills for indexable inserts Technical Specification Part 308: Creation and exchange of 3D models Milling cutters with arbor hole for indexable inserts Technical Specification
29、 Part 309: Creation and exchange of 3D models Tool holders for indexable inserts Technical Specification Part 311: Creation and exchange of 3D models Solid reamers Technical Specification Part 312: Creation and exchange of 3D models Reamers for indexable inserts Technical Specification Part 401: Cre
30、ation and exchange of 3D models Converting, extending and reducing adaptive items Technical Specification Part 405: Creation and exchange of 3D models Collets Technical Specification The following parts are under preparation: Part 70: Graphical data layout Layer settings for tool designs Technical S
31、pecification Part 71: Graphical data layout Creation of documents for the standardized data exchange Graphical product information Technical Specification Part 72: Creation of documents for the standardized data exchange Definition of properties for drawing header and their XML data exchange Technic
32、al Specification Part 305: Creation and exchange of 3D models Modular tooling systems with adjustable cartridges for boring Technical Specification Part 310: Creation and exchange of 3D models T urning tools with carbide tips Technical Specificationvi ISO 2016 All rights reservedPD ISO/TS 13399-401:
33、2016ISO/TS 13399-401:2016(E) Introduction This part of ISO/TS 13399 defines the concept, the terms and the definitions on how to design simplified 3D models of converting, extending and reducing adaptors used together with 3D models of cutting tools for NC-programming, simulation of the manufacturin
34、g processes and the determination of collision within machining processes. It is not intended to standardize the design of the adaptors and cutting tool itself. An adaptive item is used in combination with a cutting tool in a machine to remove material from a workpiece by a shearing action at the cu
35、tting edges of the tool. Cutting tool data that can be described by ISO/TS 13399 (all parts) include, but are not limited to, everything between the workpiece and the machine tool. Information about inserts, solid tools, assembled tools, adaptors, components and their relationships can be represente
36、d by ISO/TS 13399 (all parts). The increasing demand providing the end user with 3D models for the purposes defined above is the basis for the development of this series of International Standard. The objective of ISO/TS 13399 (all parts) is to provide the means to represent the information that des
37、cribes cutting tools in a computer sensible form that is independent from any particular computer system. The representation will facilitate the processing and exchange of cutting tool data within and between different software systems and computer platforms and support the application of this data
38、in manufacturing, planning, cutting operations and the supply of tools. The nature of this description makes it suitable not only for neutral file exchange, but also as a basis for implementing and sharing product databases and for archiving. The methods that are used for these representations are t
39、hose developed by ISO/TC 184 for the representation of product data by using standardized information models and reference dictionaries. Definitions and identifications of dictionary entries are defined by means of standard data that consist of instances of the EXPRESS entity data types defined in t
40、he common dictionary schema, resulting from a joint effort between ISO/TC 184/SC 4 and IEC/TC 3/SC 3D and in its extensions defined in ISO 13584-24 and ISO 13584-25. ISO 2016 All rights reserved viiPD ISO/TS 13399-401:2016PD ISO/TS 13399-401:2016Cutting tool data representation and exchange Part 401
41、: Creation and exchange of 3D models Converting, extending and reducing adaptive items 1 Scope This part of ISO/TS 13399 specifies a concept for the design of adaptive items, limited to any kind of converters, extenders and reducers, together with the usage of the related properties and domains of v
42、alues. This part of ISO/TS 13399 specifies a common way of designing simplified models that contain the following: definitions and identifications of the design features of converting, extending and reducing adaptors, with an association to the used properties; definitions and identifications of the
43、 internal structure of the 3D model that represents the features and the properties of converting, extending and reducing adaptors. The following are outside the scope of this part of ISO/TS 13399: applications where these standard data may be stored or referenced; concept of 3D models for cutting t
44、ools; concept of 3D models for cutting items; concept of 3D models for tool items; concept of 3D models for other adaptive items not described in the scope of this part of ISO/TS 13399; concept of 3D models for assembly items and auxiliary items. 2 Normative references The following documents, in wh
45、ole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 10889-1, Tool holders with cylind
46、rical shank Part 1: Cylindrical shank, location bore Technical delivery conditions ISO 12164-1, Hollow taper interface with flange contact surface Part 1: Shanks Dimensions ISO/TS 13399-3, Cutting tool data representation and exchange Part 3: Reference dictionary for tool items ISO/TS 13399-4, Cutti
47、ng tool data representation and exchange Part 4: Reference dictionary for adaptive items ISO/TS 13399-50, Cutting tool data representation and exchange Part 50: Reference dictionary for reference systems and common concepts TECHNICAL SPECIFICATION ISO/TS 13399-401:2016(E) ISO 2016 All rights reserve
48、d 1PD ISO/TS 13399-401:2016ISO/TS 13399-401:2016(E) ISO/TS 13399-60, Cutting tool data representation and exchange Part 60: Reference dictionary for connection systems ISO/TS 13399-80, Cutting tool data representation and exchange Part 80: Creation and exchange of 3D models Overview and principles I
49、SO 26622-1, Modular taper interface with ball track system Part 1: Dimensions and designation of shanks ISO 26623-1, Polygonal taper interface with flange contact surface Part 1: Dimensions and designation of shanks ISO 26623-2, Polygonal taper interface with flange contact surface Part 2: Dimensions and designation of receivers 3
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1